User Manual

ManualsBrandsSercomm ManualsElectronicsZigBee CO Detector

SZ-COD01 ZigBee Carbon Monoxide Alarm Installation Guide

The SZ-COD01 is a Carbon Monoxide Alarm that is designed to measure CO levels and sound an alarm before dangerous levels

of CO accumulate in an environment. Carbon Monoxide, which is known as CO, is odorless, tasteless, transparent and toxic - it’s a

silent killer. The SZ-COD01 is a device that can be used to detect the presence of the CO gas in order to prevent carbon monoxide

from poisoning human bodies.

Specification

Sensor Electrochemical carbon monoxide sensor

Batter Type DC 4.5V (3 x AA 1.5V alkaline battery)

Operating Temperature

0 C to 50 C (32° - 122°F)

Operating Humidity 10% to 95% Non-condensing

Alarm Audibility At least 85 dB at 3 meters

Dimention 125mm (diameter) x 35mm (depth)

Package Contents

LEDs

 Power on Mode: All three LEDs (Power/Alarm/Fault) blink and the device will beep for 0.5 second as soon as the batteries

are installed.

 Stand-by Mode: The Power (green) LED flashes once every 60 seconds, which means the device is receiving power and

functioning properly.

 CO Alarm Mode: When the device detects CO, the Alarm (red) LED flashes rapidly with repeating 4 quick loud beeps and

another 4 quick beeps after pausing for 5 seconds.

 Low battery Mode: The Fault (yellow) LED flashes once and the device beeps once a minute. This warning should last for

up to 30 days. Please replace the batteries before power is running out.

 Malfunction (Error) Mode: The Fault (yellow) LED flashes three times and the device beeps once a minute. This indicates

the device is malfunctioned and needs to be replaced.

 Low sensitivity (Aging) Mode: The Fault (yellow) LED flashes twice and the device beeps once a minute. This means the

device needs to be replaced.

 End of life signal Mode: The device will beep once and the yellow LED flashes four times a minute. This indicates the

device is reaching the end of this useful life (around 5 years after the unit is purchased), please replace with the new

SZ-COD01.

Summary of content (5 pages)

PAGE 1
SZ-COD01 ZigBee Carbon Monoxide Alarm Installation Guide The SZ-COD01 is a Carbon Monoxide Alarm that is designed to measure CO levels and sound an alarm before dangerous levels of CO accumulate in an environment. Carbon Monoxide, which is known as CO, is odorless, tasteless, transparent and toxic - it’s a silent killer. The SZ-COD01 is a device that can be used to detect the presence of the CO gas in order to prevent carbon monoxide from poisoning human bodies.
PAGE 2
 Tamper Mode: The device will beep once a minute and the yellow LED is steadily on until the device is mounted back to the bracket properly. Intallation Battery Installation/Replacement 1. Press the transparent locker of the device and remove the battery cover. 2. Install the supplied three AA batteries correctly. 3. Attach the battery cover to the device. Note: The battery cover cannot be closed if the three AA batteries are not installed properly. 4.
PAGE 3
 Do not place in close proximity to an automobile exhaust pipe; this will damage the device Wall Mounting 1. Draw a six inches horizontal line at the place where you are going to install the device. 2. Rotate the mounting bracket counterclockwise to remove it from the device. 3. Draw 2 marks to locate the mounting plugs and screws. 4. Drill two holes at the marks and insert wall plugs. 5. Attach the bracket to the wall by using the supplied two screws and wall plugs. 6.
PAGE 4
1. Join Function For "Join" a network, please do the following instruction:  2. Press the Join/Leave button for less than 1 second. The Join/Leave LED is blinking while processing. If the device has been joined with the controller successfully, the Join/Leave LED will be on for 2 seconds and then off. The Join/Leave LED will be off instantly if failed. Leave Function For "Leave" a network, please do the following instruction:  3.
PAGE 5
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.