User's Manual

ManualsBrandsSercomm ManualsElectronicsZigBee Motion Sensor

SZ-PIR04N ZigBee Motion Detector Installation Guide

SZ-PIR04N is a PIR (Passive Infrared) sensor, which can detect levels of infrared radiation from objects in its range of view. This

Motion Detector is fully compatible with any ZigBee coordinator that are HA 1.2 certified.

It is also a pet immune motion sensor, which is used to ignore the motion caused by animals and thus reduce the likelihood of false

alarms. The sensitivity of the sensor will disregard the motion caused by animals under 85 pounds, like a full-grown dog or small

cats.

In addition, the SZ-PIR04N has walk test mode and white light immunity, which can be used to reduce false alarms caused by

lights, flashlights or other reflective objects. These outstanding features of the sensor provides the professional security for

protecting any home or business to save time, money and deliver a great surveillance experience as well.

Specification

Frequency

2.4 GHz

Battery Type

GP CR123A (1400 mAh) * 2

RF Transmission Range

Outdoor: 300 Meters

Temperature Sensor

±1 C Accuracy

Light Sensor

0~2500 Lux

Rearm Timer

3 Minutes

Operating Temperature

0 C to 50 C (32° - 122°F)

Storage Temperature

-20 C to 65 C (-4° - 149°F)

Battery Life

5 Years (Assume 30 events per day @25°C)

Dimensions (H xW x D)

93.4mm x 50mm x 31.8mm

Detect Range

Distance: Max. 15M (±1M) w/mounting height 1.8M @25°C

Angle: Max. 90 (±10) Degree

Package Contents

Intallation

1. Detach the mount bracket from the device.

2. Install the provided batteries correctly.

3. Attach the mount bracket back to the device.

Summary of content (5 pages)

PAGE 1
SZ-PIR04N ZigBee Motion Detector Installation Guide SZ-PIR04N is a PIR (Passive Infrared) sensor, which can detect levels of infrared radiation from objects in its range of view. This Motion Detector is fully compatible with any ZigBee coordinator that are HA 1.2 certified. It is also a pet immune motion sensor, which is used to ignore the motion caused by animals and thus reduce the likelihood of false alarms.
PAGE 2
Operation 1. PIR LED (Red) 5. Battery Cover (Wall Mount Bracket) 2. Tamper Switch 6. Walk Test Switch 3. Pairing LED (Green) 4. Batteries  When the batteries are installed, the PIR LED will be blinking for 30 seconds and then turn off when the Motion Sensor is ready to be used.  After the tamper switch is pressed, the Motion Detector will be in normal mode. The PIR LED on the device will illuminate when the Motion Detector is triggered.
PAGE 3
Mounting Instruction The recommended mounted position for a Motion Detector should be 1.8M from the floor in the corner of a room. At this height, the device can detect a movement up to 15M (±1M ) (see the following image). Also, in this position, the 90 degrees (±10 degree) fan-shaped detection pattern can normally offer greater protection than mounting on a flat wall. Before selecting a position, the following installation hints should be noted: 1.
PAGE 4
Wall Mounting Note: The device is suggested to be set at 90 degrees angle, which is the best mounted position for offering the 15M protection area. 1. 2. Detach the mount bracket from the device. Mount the bracket with the supplied screws/anchors into the wall. It can be either mounted on a flat surface or in a corner. Note: Make sure the mount bracket is installed in the correct direction (upwards arrow). 3. Attach the device to the mount bracket.
PAGE 5
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.