Robot Vacuum Cleaner User Manual
CONTENTS PRODUCT SPECIFICATION FAQs – Product Setup Video – Contact Us www.PureCleanHome.
Safety Instructions Before using this product, please read the safety instructions! ● Read this user manual thoroughly and carefully before using this product. ● Keep this user manual and save it for future reference. ● Any operation that does not comply with this manual may cause damage to the product. 1. Only authorized technicians should disassemble the product. 2. Only use the original battery and power adapter of the product for charging.
WARNING: The appliance is not intended for children under 8 years old, people with reduced physical, sensory or mental capabilities, or lack of experience and knowledge. Proper supervision or instruction should be given to help them understand the hazards involved, and how to use the appliance in a safe way. Do not use the product in any area higher than the height of the user, so as to prevent the machine from falling to cause injury.
Product Features 2. Spot cleaning mode The robot will clean intensively in a spiral way with more power, suitable for an open area with much dust. 3. Edge cleaning mode In this mode the robot will clean along the wall or obstacles. 4. Scheduling mode After being scheduled, the robot will leave charging station and start working at scheduled time.
Product Components Main body and Accessories No.
Product Components Main Body Diagram Bumper Upper cover Button Universal wheel Battery cover Left side brush Right side brush Suction passage Bottom cover Right wheel Power switch Bottom cover Upper cover Dust bin Charging socket Dust Bin Primary filter Dust bin HEPA filter HEPA filter shelf 5
Product Components Charging Station Signal receiver Power light Infrared signal transmitting window Top cover Power supply socket Charging poles Remote Controller 1. Digital display 2. Auto charging 3. Scheduling button 4. Direction buttons 5. ON/OFF 6. Mode selection button 7. Spot cleaning button 8. Time setting button A. Install two AAA type batteries into the remote controller before use. B. Remove the batteries if the remote controller will be left unused for a long period. C.
Product Components Display Panel A. Switch on robot, press CLEAN button or ON/OFF on remote, robot will beep twice and enter in standby status, the indicator will flash blue. B. Press CLEAN button or ON/OFF on remote again, robot will beep three times and the indicator will flash blue quickly, if its function is normal, robot will start cleaning, and the indicator stay blue during cleaning. C.
Product Operation Battery Charging 1. Charging station placement Place charging station against the wall and remove obstacles within 1 meter at two sides and 2 meters ahead. As shown in the right figure. 2. If the robot has been shut down, power on it by turning on the power switch at the right side of the robot before charging. 3. Charge the robot in either of following way as shown: a. Plug the adapter into the robot and plug the other end into the power socket, as shown in Fig A. b.
Product Operation Starting Up/ Standby/ Sleep mode/Power off 1. Starting up A. Power on the robot by turning on the power switch at the right side of machine. Press CLEAN button or ON/OFF on remote, robot will beep twice and enter in standby status, CLEAN indicator light will flash blue gradually. B. In standby, press CLEAN button on main body or ON/OFF on remote to start cleaning.
Product Operation Scheduling You can schedule the robot to make it start cleaning automatically at a certain time everyday. 1. The robot can only be set when it’s in standby or charging on the docking station. (If the robot is in cleaning, pause it before scheduling. If the robot is in sleep mode, long press CLEAN button on main body or ON/OFF on remote controller to wake it up. If the robot is in deep sleep-power off, long press CLEAN button on main body to wake it up.) 2.
Product Operation Note: A. The robot will work at the scheduled time everyday if schedule is not canceled. B. All scheduling will be canceled if you switch off / power off the robot (If no operation on robot for 1 minute, it will turn to sleep mode. If no operation for 15 minutes, it will turn to deep sleep and power off, scheduling will be canceled.
Product Operation 1.4 Edge cleaning ( mode 3 ) In this mode, robot will clean along the wall or obstacles. Note: A. Switch on the robot, press MODE on the remote controller and select edge mode. B. Under edge cleaning mode, the robot will do cleaning along the obstacle by its side brushes. 1.5 Zigzag cleaning ( mode 4 ) The robot will automatically go into Zigzag cleaning when it detected it’s in an open area or the environment with less obstacles.
Product Maintenance 1. Cleaning Side Brushes Clean the side brush when it gets dirty and replace it if it's damaged. Maximum life span for side brush is 12 months. Note: Before replacing side brushes, please pay attention to the left mark and the right mark (‘L’/ ‘R’) on side brushes, which match with the ‘L’/ ‘R’ mark on the bottom base of robot. 2. Cleaning Dust Bin and Filters Empty and clean dust bin after each use following the steps as shown in the below figures: Press A.
Product Maintenance 3. Cleaning Sensors and Wheels Slightly wipe all sensors and wheels, as marked in above figure, with soft cloth or tool. 4. Cleaning Charging Poles Cleaning the charging poles as marked in below figure, with soft cloth or tool.
5. Cleaning Suction Passage Cleaning the suction passage, as marked in below figure, with soft cloth or tool. Note: Pay attention and avoid wetting the sensors. 6. Mopping Cloth Usage A. Stick mopping cloth on mop plate fix them at the bottom of the robot, as shown in right figure. B. When the mopping cloth is dirty, please wash and clean it. You can change a new one if needed. Note: Do not clean the appliance under water.
www.pyleusa.com/contactus Troubleshooting Problem Possible Cause Solu�on Robot suddenly stops cleaning and indicator stays blue. Robot was picked up (sensors detect cliff or wheel off the ground). Put the robot on the solid floor and re-start the robot. Place the robot on ground, turn on the robot, its indicator is in blue ( without charging). Cliff sensor fault. 1. Clean cliff sensor. 2. If solu�ons given above doesn’t work, send it to the seller for repair.
www.pyleusa.com/contactus Product Specification Classifica�on Electrical Specifica�ons Item Ba�ery Voltage Ba�ery Specifica�ons Consump�on Power Func�onal Specifica�ons Detail DC 14.4V Ni-MH 1500mAh 15W Dust Bin Capacity 0.3L Charging Type Cleaning Mode Auto Charging / Manual Charging One-Key Clean & Mode Selec�on by Remote Controller Cleaning Time 80 minutes Button Type Type of of Main Bu�on MainBody Body Press Bu�on Note: Particular specifications are subjected to change without prior notice.
www.pyleusa.
