by SLRD36WIFI
catalog FCC Information 3 Notice 3 Specification 5 Name of Parts 5 Installation of Propeller Guard 6 Landing Gear Installation Diagram 7 Transmitter Installation 7 Charging Instruction 8 Pre-flying Operation 9 Additional Instruction before Flying 10 Flying Control 11 High / Low Speed Mode 12 Flip Mode 12 Low Battery Alarm 12 Heading Hold Mode 13 Installation and Replacement for Motor and Propeller 13 Operation Instruction for Mobile Phone WiFi 14 Setting 20 Help 21 To r
FCC Information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.These limits are designed to provide residential protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not Installed and used in accordance with the instructions, may cause harmful interference to radio communications.
(1) Keep away from obstacles and crowd The speed and status of a flying RC drone is uncertain and it may cause potential danger. So the user must keep away from crowd, tall building, power lines etc. when operating a flying RC drone. Do not fly a RC drone in rainy, storm, thunder and lighting weather for the safety of user, around people and their property. (2) Keep away from humid environment The drone inside is consisted of precise electronic components.
Specification Drone Size Drone Weight Propeller Diameter Flying Time Drone Battery 480x480x120mm Charging Time for Drone Battery 355g 190mm 6~7mins 140~160mins Max Flying Distance/Radius 100 m Max Image Transmission Distance/Radius 35 m 3.7Vx2 1000mAh Camera Resolution 1280x720P Name of Parts 1.
2. Transmitter Lens Hood Mobile Phone Screen Power Indicator Light Forward / Backward Trimmer Power Switch Left Stick (Throttle / Rudder) Right Stick (Forward / Backward / Left / Right) Rotation Trimmer Left / Right Trimmer Heading Hold Mode Flip Mode High / Low Speed Mode LCD Screen Picture 3 Heading Hold Mode Icon Flip Mode Icon Indication Direction of Power Switch High / Low Speed Mode Icon Installation of Propeller Guard 1.7*6PB Screws Picture 4 1.
Landing Gear Installation Diagram To install the Landing Gear, insert the Landing Gear’s pillars into the drone body holes with moderate force as the diagram shown. Note: Please ensure the Landing Gear can stand firm on the ground. Or the flight stability would be effected. Picture 5 Transmitter Installation: Battery installation: open the battery cover on the back side of the transmitter and put 4 alkaline batteries (not included) into the box in accordance with electrode instructions.
Picture 7 Picture 8 3. Insert the lens hood to the slot and make sure the lowe edge of the lens hood next to the mobile phone closely as Picture 9. Picture 9 Charging Instruction 1. Connect the USB wire with one of the USB port listed in the below picture first, and then connect the drone battery with the USB wire. (prior to choose 2A, 5V charger) 2. After connecting the USB wire with the USB port, the green USB indicator light keeps bright.
Pre-flying Operation: 1. Turn on the transmitter switch (Picture 10) and its indicator light flashes quickly. Push the Left Stick to utmost control distance and then to the low end (Picture 11/12). The indicator becomes flash slowly, which indicates the transmitter enters frequency pairing. Picture 10 Picture 11 Picture 12 2. Press the battery box buckle at the tail of the drone and then pull it out (Picture 13). Picture 13 Press and pull out 3.
5. Insert the TF card to the card slot at the rear part of the camera, and then turn on the power switch. The LED lights start to flash. Put the drone on the horizontal position to calibrate the gyro. The transmitter beep constantly about three seconds later, which indicates successful code pairing and the LED lights get a solid bright. OFF ON 2. Turn on the switch 1.
3) Turn on the drone switch and put the drone on a flat surface in horizontal position. The drone tail face to the user and the drone head faces forward. You will hear “ di, do, di” three seconds later, which indicates successful code pairing. The fuselage lights get a solid bright. 4) Do not move the Left Stick before successful calibration. Push the Right Stick as Picture 19 and then release. The drone body lights flash, which indicates that the drone is calibrating.
6. If the drone tilts forward or backward Tilt forward Tilt Backward Pull down the Forward / Backward Trimmer till balance if the drone drifts forward, and push up the Forward / Backward Trimmer if the drone drifts backward. 7. If the drone tilts to the left or right Drift left Drift Right Move the Left / Right Trimmer to the right till balance if the drone drifts to the left, and move the Left / Right Trimmer to the left till balance if the drone drifts to the right. High / Low Speed Mode 1.
Heading Hold Mode * Drones generally have a front and rear indicated by LED lights or colored propellers. By default, the users are required to tell the front and the rear of the drone when flying. Under heading hold mode, the users can operate the drone without worrying about the orientation (left is left and right is right all the time, regardless of where your drone is pointing at). Heading Hold Mode is designed for beginners and users who fly the drone in daylight or at a far distance.
2. Motor Replacement Replace the damaged or performance degradation motor as below steps. 1. Remove the LED shade and four screws of the motor holder (Picture 24). 2. Remove two motor screws and replace the damaged motor with a new one (Picture 25). Picture 24 Picture 25 Note: Ensure that red motor plug paired with red motor port, white motor plug paired with white motor port. A Propeller for clockwise motor and B Propeller for counterclockwise motor.
Click Picture 29 4. Click icon Picture 30 udirc-FPV and enter remote control interface as Picture 31. Click Picture 31 Introduction for Mobile Phone Control Tip: Following “ Pre-flying Operation” before entering mobile phone control function. 1. Back to main menu 1 Touch icon to return Exit from work interface. 2. To view photo and video 2 Touch icon to view photo and video.
3. To view the screen without controls Touch 3 icon to view your screen without controls. 4. High / Low speed mode 4 Touch icon (Low Speed), turn to icon (High Speed). 5. To take photo 5 Touch icon once to take a photo. 6. To record video 6 Touch icon to record a video, and touch icon again to stop recording.
7. To fly up and down Move the Left Ball up to fly the drone up and move the Left Ball down to fly the drone back down. 10 8. To rotate left and right Move the Left Ball to the left to rotate the drone to the left. Move the Left Ball to the right to rotate the drone to the right. 11 12 Left Right 9. To fly right and left Move the Right Ball to the left to fly the drone to the left and move the Right Ball to the right to fly the drone to the right.
10. To fly forward and backward Move the Right Ball up to fly the drone forward and move the Right Ball down to fly backwards. 15 16 11. To turn on Gravity Induction Mode Touch 7 icon to enter gravity induction mode, which is only available for flying left / right and forward / backward. If the mobile phone shakes to the left / right, the Right Ball will move accordingly causing the drone to fly left / right.
12. To turn on Heading Hold Mode 8 Touch icon to enter Heading Hold mode. Touch icon again and exit from Heading Hold mode. 13. VR (virtual reality) Mode Touch 9 icon to enter the mobile phone split screen mode. Touch icon again to exit from VR mode. * This function is only available when using a VR Headset (excluded). 14.
15. If the drone rotates to left or right Adjust tee Left / Right Rotation Trimmer to the right if the drone rotates left, and adjust the trimmer to the right to balance if the drone rotates right. Left 19 Right 20 16. If the drone flies left or right Adjust the Left / Right Flying Trimmer to the right if the drone flies left, and adjust the trimmer to the left to balance if the drone flies to right. 21 22 1.
Help In the interface, click the icon (as Picture 34) and enter help interface (as Picture 35, 36, 37). HELP 1. Turn on the product ( Four axis aircraft ). 2. Enter the “Settings”menu of your mobiledevice. 3. Then turn on “WiFi” and Connect to the AP of this Product. 4. Enter the control interface of this APP,you would see the real-time video from the aircraft camera,and you now can start your flight.
Exploded View 1 2 8 4 3 6 7 8 5 7 9 13 10 11 12 16 14 15 No. Name No.
Spare Parts For convenience, the spare parts are listed for you to choose, which can be purchased from the local distributor.
Troubleshooting Guide No. Problem Problem Cause Solution 1. Low battery. 1 2 1. Replace the transmitter battery. The 2. The battery positive pole and negative transmitter pole are in reverse order. indicator light is off 2. Install the battery in accordance with the user manual. 3. Poor Contact. 3. Clean the dirt between the battery and the battery slice. 1. Indicator light is off. 1. The same as above 1.2.3. 2. There is interfering signal nearby. 2.
