Executive Chair Silla Ejecutiva Assembly Instructions Instrucciones de Ensamblaje Model/ Modelo: 43673
Parts/Partes FRONT A Casters Ruedas Quantity/cantidad: 5 E1 Left Arm Brazo izquierdo Quantity/cantidad: 1 B Star Base Base en forma de estrella Quantity/cantidad: 1 E2 Right Arm Brazo derecho Quantity/cantidad: 1 C Gas Lift with Telescoping Cover Elevador neumático y cubierta telescópica Quantity/cantidad: 1 F Seat Cushion Cojín del asiento Quantity/cantidad: 1 D Seat Plate Mecanismo del asiento Quantity/cantidad: 1 G Back Cushion Cojín del respaldo Quantity/cantidad: 1 Chair Assembly Instruction
H 1” Big Screws Tornillos grandes de 25mm Quantity/cantidad: 2 L Black Plastic Caps Tapas plásticas negras Quantity/cantidad: 4 I 1-1/4” Big Screws Tornillos grandes de 32mm Quantity/cantidad: 2 J 1-1/4” Small Screws Tornillos pequeños de 32mm Quantity/cantidad: 8 M N Black Plastic Caps Tapas plásticas negras Allen Key Llave allen Quantity/cantidad: 2 K Black Plastic Caps Tapas plásticas negras Quantity/cantidad: 2 Quantity/cantidad: 1 Step 1 Place the Star Base (B) upside down and insert 5
N F I H D FRON T C FRON T D 4 F Step 3 Attach Seat Plate (D) to the bottom of the Seat Cushion (F) (with the front of the seat plate facing the front of seat cushion). Attach by using 1-1/4” Big Screws (I) for the front holes of the Seat Plate (D) and 1” Big Screws (H) for the rear holes of the Seat Plate (D) with the Allen Key (N). *Note: Align the Seat Plate so the FRONT on the seat plate matches the FRONT label on the bottom of the seat cushion. Tighten the screws completely.
E1 E1 E2 E2 J G N F N J J Step 5 Fasten the Arms (E1 & E2) onto sides of the Seat Cushion (F) by using 1-1/4” Small Screws (J) with the Allen Key (N). *Note: Do not tighten the screws completely. Step 6 Place the Back Cushion (G) flat between Arms (E1 & E2), and use 1-1/4” Small Screws (J) to locate lower screw holes on both Arms (E1 & E2) & Back Cushion (G) with the Allen Key (N) . *Note: Do not tighten the screws completely.
G E1 M E2 L M K N L J 6 K Step 7 Push the Back Cushion (G) up to a vertical position and attach the Arms (E1 & E2) by using 1-1/4” Small Screws (J) with the Allen Key (N) . *Note: Tighten all the screws completely. Step 8 Place the Black Plastic Caps (K & L & M) into arm holes once screws have been tightened. The chair is now ready for use.
Operating Instructions Instrucciones de Uso Function Instruction - 1 To Adjust Seat Height: While seated, lean forward and reach under the right side of the chair to find the handle. Lift the handle and raise your body up slightly to allow the chair to rise to the desired height. Once desired height is reached, release handle to lock chair at desired height. To lower the seat, lift the handle while seated. The chair will descend until the handle is released or the chair reaches the bottom position.
Function Instruction - 2 To Operate Tilt Lockout: While seated, reach under the right side of the chair to find the height adjustment handle. Pull the handle all the way out (away from the seat plate) to allow the chair to tilt backwards. To lock the chair in the upright or vertical position, sit upright and push the handle in towards the seat plate.
Function Instruction - 3 To Adjust Tension On The Tilt: Reach under the front center of the chair, grasp the round knob (R) and turn it counter - clockwise to stiffen the tilt mechanism for a heavier user. Turn the knob (R) clockwise to loosen the tilt mechanism for a lighter user. Rotate the knob (R) until the desired resistance is reached.
Limited Warranty True Innovations seating products are warranted against defects in material and workmanship while owned by the “Original Purchaser”. The term “Original Purchaser” is defined as that party or entity which purchases True Innovations furniture from an authorized True Innovations retailer as shown by the original sales receipt. This warranty does not apply to “as is” or previously owned seating products.
Garantía Limitada Los productos de True Innovations seating están garantizados contra defectos de material y mano de obra mientras está en posesión de su “Comprador Original”. El término “Comprador Original” se define como el individuo o entidad que compra el mueble de True Innovations de un distribuidor autorizado así demostrado por el recibo original. Esta garantía no le aplica a muebles usados comprados “como tales”.
