Table of Contents ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Introduction ............................................................ 1 Key Features........................................................... 2 Specifications......................................................... 3 Packing Checklist .................................................. 4 Product Description............................................... 5 Installation .............................................................. 6 Video Compensation ......
------------------------ Introduction The ServerLink Extend Cat5 KVM Extender consists of a Local Computer Unit and a Remote Station Unit that can be used to locate a keyboard/monitor/mouse set up to 150 meters away from a computer or KVM switch using an inexpensive Category 5 UTP (unshielded twisted pair) cable. It provides an ideal and convenient way to remotely access the computer which is located in a secure, clean or dirty, harsh environment.
------------------------ Key Features Connects the Local Computer Unit and Remote Station Unit via Category 5 UTP cable Remotely locates the keyboard, mouse and monitor up to 150m from a computer Supports PS/2 Video compensation can be adjusted by hotkey to ensure the optimum signal quality for any length of cable within the limit.
------------------------ Specifications PS/2 Model SLX-202P Connections CAT5/CAT5e/CAT6 – RJ45 female Remote Station Unit Connectors Console Local PC Local Computer Unit Connectors Local Console PC miniDIN6, female x 2 HDB15 female x 1 HDB15 female x 1 miniDIN6, female x 2 HDB15 female x 1 HDB15 female x 1 LED Indicators (Remote Station Unit) Local Remote On: Controls local PC On: Controls remote PC LED Indicators (Local Computer Unit) Local Remote On: Controls local PC On: Local PC is contr
------------------------ Packing Checklist z ServerLink Extend Cat5 KVM Extender Remote Station Unit x 1 z ServerLink Extend Cat5 KVM Extender Local Computer Unit x 1 z Power Adapter – 9V DC, 600mA x 1 z User Manual x 1 z Foot Pad x 2 sets z KVM Cable x 2 (LKS-02H) NOTE: USE OF POWER SUPPLY • NOT required if you have a computer connected to both Station and Local Computer Units • Required if there is NO computer connected to Remote Station Unit.
------------------------ Product Description Figure 3: Indication and Connection 5
---------------------- Installation Connection Pattern Figure 4: Connection pattern of ServerLink Extend Cat5 KVM Extender • • • • • • A keyboard, mouse and monitor must be connected to the Remote Station Unit. You do need to connect a computer to the Remote Station Unit. Optional Power Supply is required if there is NO computer connected to Remote Station Unit. A computer must be connected to the Local Computer Unit.
------------------------ Video Compensation Before operating, Video Compensation should be conducted. Hotkeys are used to adjust the Equalization on the Remote Unit to achieve optimum video signal for various cable lengths. There are five segments of CAT 5 cable lengths can be chosen from. To achieve the best visibility, please refer to the chapter of “Remote Station Unit Hotkeys Control” to adjust the video compensation.
------------------------ LED Indicators The LEDs on the ServerLink Extend Cat5 KVM Extender show the latest status which indicates the linking, communication, and control situation between Local Computer Unit and Remote Station Unit. Remote Station Unit LED Status Control Description Remote: Off, Local: On Remote Station Unit controls its local PC. Remote Station Unit is remotely taking control of the Local Computer Unit. In this mode, there are two statuses as follows: 1.
Local Computer Unit LED Status Control Description Local Computer Unit controls its local PC. In this Remote: Off, Local: On mode, the Remote Station Unit cannot take control of the Local Computer Unit remotely. Remote Station Unit is remotely taking control of the Remote: On, Local: Off Local Computer Unit.
-----------------Push Button: Switch to the control status The button on the panel of Local Computer Unit and Remote Station Unit respectively, can be pushed (switched) in sequence to select the operation modes. Button on Remote Station Unit The button on the panel of Remote Station Unit can be pushed (switched) in sequence to select the following two modes: Loc → Com(Remote) Local: Remote: The LED of Local is “On”. In this mode, the system controls its local computer. The LED of Remote is “On”.
Button on Local Computer Unit There are three modes that can be chosen, the sequence is as follows: Auto → Loc → Com(Remote) Auto: • • • • • • Local: Remote: In this mode, the Remote and Local LEDs are flashing alternately. The system is now waiting to be controlled by either Local Computer Unit or Remote Station Unit. Once the keyboard or mouse of Local Computer Unit is active, the LED of Local is on and the LED of Remote is off.
-----------------Hotkeys Control Hotkey commands are short keyboard sequences to select a computer, to activate computer scan, and so forth. The ServerLink Extend Cat5 KVM Extender is always interpreting keystrokes for hotkeys. A hotkey sequence starts with two left Ctrl keystrokes followed by one or two more keystrokes. A built-in buzzer generates a high-pitched beep for correct hotkey command, while one short and one long beeps are sounded for wrong commands.
--------------Remote Station Unit Hotkeys Control Hotkey Commands Function Description *Ctrl + Ctrl + Ti Toggles console control between Local Computer and Remote Computer Ctrl + Ctrl + Esc Escape from hotkey mode *Ctrl + Ctrl + 1i Switches control to local computer Switches control to remote computer(input allowed only if the Local Computer Unit is in Remote or Auto mode) Toggles console control between Local Computer and Remote Computer *Ctrl + Ctrl + 2i *Ctrl + Ctrl + F2 Ctrl + Ctrl + F4 (Keybo
---------Local Computer Unit Hotkeys Control Hotkey Commands Ctrl + Ctrl + Ti Ctrl + Ctrl + Esc Ctrl + Ctrl + 1i Ctrl + Ctrl + 2i Function Description Toggle switch selects Auto-Loc-Rem mode Escape from hotkey mode Local Mode: Allows the user at local computer exclusive access to the system; remote access from computer at Remote Station Unit is disabled.
-----------------Appendixes Cable Requirements The cable use to connect the Local Computer Unit and Remote Station Unit can be either Category 5, Category 5e or Category 6 terminated with RJ45 connectors. These are purchased separately. This cable is not provided with the standard package because it is subject to the different lengths you may require. The length of cable used should be less than 150m, otherwise poor results, especially for video resolution, may occur over distances beyond the limit.
The above diagram shows the RJ45 connector CAT5/CAT5e/CAT6 cable with its metal contacts facing up. of a Limited Warranty IN NO EVENT SHALL THE DIRECT VENDOR'S LIABILITY FOR DIRECT OR INDIRECT, SPECIAL, INCIDENTIAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFIT, LOSS OF BUSINESS, OR FINANCIAL LOSS WHICH MAY BE CAUSED BY THE USE OF THE PRODUCT EXCEEDS THE PRICE PAID FOR THE PRODUCT.