Unit installation

ManualsBrandsserverLink ManualsComputer equipmentExtend Cat5

PAGE 1

05/23/2014

12/24V (Green) - Power LED.

Relay 1 (Orange) - The relay is energised - (NO/COM contacts are closed).

Relay 2 (Orange) - The relay is energised - (NO/COM contacts are closed).

Alarm (Red) - 12V Alarm output is active.

Exit (Orange) - The exit button contacts are closed.

Contact (Orange) - The door contacts are closed.

Tamper (Orange) - The tamper contacts are closed.

PSU (Orange) - The PSU contacts are closed.

OK (Green ash) - The internal software is running.

Termination (Red) - The on-board resistors are in place across the RS485 data pairs.

Rx (Red) - The ACU is receiving data (TCP/IP or RS485) - See also FAQ section.

Tx (Green) - The ACU is responding to data - (TCP/IP or RS485).

Server Connected (Green) - The TCP/IP interface is communicating with the PC Net2 server.

Server Link - Green = 100 Mbit/s : Orange = 10 Mbit/s (TCP/IP speed).

LED indications

Ins-40080-US Net2 plus control unit - UL

Paxton

Technical Support

Technical help is available: Monday - Friday from 02:00 AM - 8:00 PM (EST)

1.800.672.7298

supportUS@paxton-access.com

Documentation on all Paxton products can be found on our web site - http://www.paxton-access.com/

For instructions in alternative languages - http://paxton.info/1000

The Net2 plus ACU has 2 reader ports and 3

output relays, but can control just one door.

The conguration of one control unit per door

greatly simplies installation and is ultimately

highly cost eective.

For a fail open lock (Maglock), wire 0V to the

"N.C." terminal instead of "N.O."

Wiring

Net2 plus

PSU

ARM

SENSE

N.C.

N.O

COM

N.C.

N.O

COM

Data/D0

Clock/D1

CAT5

RS485

Media

Detect

TX RX

100

Data/D0

Clock/D1

Media

Detect

10/100 Ethernet

N.C.

N.O

COM

12V - 24V

12V

LED

12V

LED

EXIT

PSU

12V DC

Net2 plus

PSU

ARM

SENSE

N.C.

N.O

COM

N.C.

N.O

COM

Data/D0

Clock/D1

CAT5

RS485

Media

Detect

TX RX

100

Data/D0

Clock/D1

Media

Detect

10/100 Ethernet

N.C.

N.O

COM

12V - 24V

12V

LED

12V

LED

EXIT

PSU

12V DC

dae

noi

C yl

eda

V21 roF

12V

Red LED

Amber LED

Green LED

Data/D0

Clock/D1

Media Detect

12V

Red LED

Amber LED

Green LED

Data/D0

Clock/D1

Media Detect

N.C.

N.O.

COM

N.C.

N.O.

COM

Alarm

12V

Green LED

Exit

stupnI

tputsuO

rewoP

12V

Contact

Tamper

PSU

repmaT/USP

tnoC

ttu

2 yaleR

aleR

Expansion

RS485 Network

CAT5 Cable Coding

G/thW

rap

ro n

erc

atad

orf

eroc

bac

gnrO/th

egn

10/100 Ethernet

Server Connected

Server Link

100

End of Line Termination

OFF

Net2 plus

Intruder Alarm

Set

mrA

esneS

MOC

O.N

LABEL HERE

http://paxton.info/107

123456

00-01-02-03-04-05

2345612

dae

tuaC ylno

sreda

r C

roF

stupnI

tputsuO

rewoP

repmaT/USP

tcatnoC

nottuB tixE

yaleR

RS485 Network

CAT5 Cable Coding

nrG/thW

era

eercS

orf seroc

lbac

gnrO/thW

10/100 Ethernet

Server Connected

Server Link

100

End of Line Termination

OFF

Net2 plus

Intruder Alarm

DC Only

Set

12-24V

MOC

.O.N

123456

00-01-02-03-04-05

2345612

http://paxton.info/107

dae

noi

C yl

eda

V21 roF

12V

Red LED

Amber LED

Green LED

Data/D0

Clock/D1

Media Detect

12V

Red LED

Amber LED

Green LED

Data/D0

Clock/D1

Media Detect

N.C.

N.O.

COM

N.C.

N.O.

COM

Alarm

12V

Green LED

Exit

stupnI

tputsuO

rewoP

12V

Contact

Tamper

PSU

repmaT/USP

tnoC

ttu

2 yaleR

aleR

Expansion

RS485 Network

CAT5 Cable Coding

G/thW

rap

ro n

erc

atad

orf

eroc

bac

gnrO/th

egn

10/100 Ethernet

Server Connected

Server Link

100

End of Line Termination

OFF

Net2 plus

Intruder Alarm

Set

mrA

esneS

MOC

O.N

LABEL HERE

http://paxton.info/107

123456

00-01-02-03-04-05

2345612

dae

tuaC ylno

sreda

r C

roF

stupnI

tputsuO

rewoP

repmaT/USP

tcatnoC

nottuB tixE

yaleR

RS485 Network

CAT5 Cable Coding

nrG/thW

era

eercS

orf seroc

lbac

gnrO/thW

10/100 Ethernet

Server Connected

Server Link

100

End of Line Termination

OFF

Net2 plus

Intruder Alarm

DC Only

Set

12-24V

MOC

.O.N

123456

00-01-02-03-04-05

2345612

http://paxton.info/107

dae

:noituaC ylno sredaer CD V21 roF

12V

Red LED

Amber LED

Green LED

Data/D0

Clock/D1

Media Detect

12V

Red LED

Amber LED

Green LED

Data/D0

Clock/D1

Media Detect

N.C.

N.O.

COM

N.C.

N.O.

COM

Alarm

12V

Green LED

Exit

stupnI

tputsuO

rewoP

12V

Contact

Tamper

PSU

repmaT/USP

tnoC

ttu

yaleR

aleR

Expansion

RS485 Network

CAT5 Cable Coding

G/thW

rap

ro n

erc

atad

morf

eroc

bac

nee

gnrO/thW

egn

10/100 Ethernet

Server Connected

Server Link

100

End of Line Termination

OFF

Net2 plus

Intruder Alarm

Set

mrA

neS

MOC

O.N

LABEL HERE

http://paxton.info/107

123456

00-01-02-03-04-05

2345612

dae

noi

tuaC ylno

sreda

er CD

V21 roF

stupnI

tputsuO

rewoP

repmaT/USP

tcatnoC

ttu

yaleR

RS485 Network

CAT5 Cable Coding

erap

s ro n

eercS

orf seroc

elbac

gnrO/thW

egn

10/100 Ethernet

Server Connected

Server Link

100

End of Line Termination

OFF

Net2 plus

Intruder Alarm

DC Only

Set

12-24V

mrA

MOC

.O.N

123456

00-01-02-03-04-05

2345612

http://paxton.info/107

Reader/keypad

(optional)

Reader/keypad

Intruder alarm

integration

from previous ACU

to next ACU

Tamper switch

(optional)

Exit button (push to make)

Normally closed door contact

(optional)

Door Lock

12V DC power

supply

TCP/IP patch lead

Switchable 120 ohm

resistors

Summary of content (12 pages)

PAGE 1
Paxton 05/23/2014 Ins-40080-US Net2 plus control unit - UL Technical Support 1.800.672.7298 supportUS@paxton-access.com Technical help is available: Monday - Friday from 02:00 AM - 8:00 PM (EST) Documentation on all Paxton products can be found on our web site - http://www.paxton-access.com/ For instructions in alternative languages - http://paxton.
PAGE 2
Overview A Net2 plus can connect to the Net2 PC using either an un-shielded RJ45 patch cable or an RS485 data line. This greatly increases the number of installation options available to the installer. One Net2 plus can also be used as the TCP/IP interface for an RS485 daisy chain of Net2 plus and Net2 classic units. When used with a TCP/IP connection, it must first be detected using the Net2 Server Configuration Utility as defined later in this instruction.
PAGE 3
Cable type Cable specification Use Max length RS485 Data Line 1000 yds Reader / Keypad 500 feet Input / Output 100 yds Type 2 x twisted pairs - Belden 8723 or Cat5 equivalent 8 core, shielded - Beldon 9538, Alpha 1298C (22AWG) or equivalent 2 conductor - Alpha 1172C (22AWG) or equivalent Mounting Parts kit Part Number Qty Fitting Kit fk1-108 1 Ferrite tube 1 Grommet, 22mm hole 3 Wall plugs 3 Pozi round woodscrew - zinc 1 Pozi panhead lid screw 1 Rubber washer 1 Cable gland 1 Cab
PAGE 4
Connecting to the PC via the Ethernet port If the TCP/IP data connection is longer than 25 ft the following surge protection device must be installed within 3 ft of the control unit. Data line surge protector. Emerson Network Power: Model LCDP-060. The IP address should be assigned a fixed value, or a DHCP reservation. Unreserved IP addresses issued by DHCP servers are not guaranteed to be constant, leading to potential failure of PC to Net2 bridge communications.
PAGE 5
This may require the routers and gateways to be configured between the networks. Again, this would be done by the Network administrator of that site. Make sure the ports listed above are open on all intermediate routers. Once installed, create a record with the;Add button (if none was created during initial set up) and you should then be able to detect its MAC by entering the IP address in the Configuration screen Ping box.
PAGE 6
Installation and test Wire the components to the Access Control Unit (ACU) as shown on the first page. Press the exit button or in the absence of an exit button short the 0V and exit terminals to test the relay function. The lock Relay LED will come on and the lock should release. Each time the unit is powered on, it will run an internal health check. During this phase (about 5 secs) the OK LED will flash quickly before changing to a slower heartbeat. The reader's default indication has all the LED's on.
PAGE 7
INPUT / OUTPUT WIRING Exit button Where fitted, a 'push to make' button is required. (See Specification table for ratings) The Exit LED will be ON when the switch is closed. Button Pushed. When the Exit terminal is shorted to 0V, the Exit LED will illuminate and the ACU will operate Relay 1. The reader/exit button Green LED will flash during this period. More than one exit button can be wired in parallel. Relay 1 will remain transfered while the short to 0V remains.
PAGE 8
Alarm sounder This local alarm has a transistor 'open drain' output, (not a dry contact relay) and will switch 1A at 12V DC for a bell, light etc. This local output can be turned on or off for each type of alarm and can be configured to sound continuously or intermittently to distinguish between different alarm types. Lock Wiring - Relay output 12V DC power supply Lock power supply Door lock Fail closed Fail open Lock with an independent supply This is a ONE door controller using a dry contact relay.
PAGE 9
Software configuration Door name: Name the Door. Door open time: Set the door open time. Unlock the Door during: Holds the door unlocked during this timezone. - Set to 'At No Time' for normal user operation. Reader 1: Settings for Reader 1 and Keypad 1 on the ACU. Reader 2: Settings for Reader 2 and Keypad 2 on the ACU. Alarm: Contains settings for the different types of alarm. Codes: Valid codes can be viewed, added and removed. (Can only be viewed when a keypad is active).
PAGE 10
Technical Help 1 - RS485 Data line resistance check - ACU not responding or fails to be detected. QFirst power down any data line converters and disconnect any ACU's that do not have a flashing OK LED. Using a QMultimeter, measure the resistance across the White/Green and Green pair at one end of the network. QA resistance of between 60 and 80 ohms is required. Repeat the test for the White/Orange and Orange pair. QThis is vital for a stable and trouble free installation.
PAGE 11
Product compliance and limitations To comply as a UL listed installation, the following conditions must apply:The power must be provided via a separate DC supply, a UL Listed Access Control (or Burglar Alarm) Class 2, Power-Limited, power source capable of 4 hours standby must be employed. This is wired into the 0V and 12/24V terminals and the cable secured with the cable ties provided.
PAGE 12
Options Sales Code Description 682-493-US Net2 plus access control unit 682-528-US Net2 plus ACU in plastic housing Specifications Electrical Min Max Voltage 12V DC 24V DC (+20%) PCB Current (depending on activity) 200 mA 3A 24V DC (+20%) Relay switchable voltage 4A Relay switchable current Alarm output voltage 12V DC Alarm output current 1A 500 mA Combined reader port output current Reader port voltage 11.4V DC 12V DC Exit button voltage 11.