Owner Manual

GENERAL CLEANING
1. Rinse Airpot with hot water thoroughly several times
including pumping out the hot water through the
nozzel at least 12 full strokes using the pump or lever
style lid. Clean the interior with dish detergent and a
soft sponge or cloth taking care not to scratch the glass
or stainless liner. Rinse with hot water again. Do not
submerge the airpot in water at any time.
2. Add 1 tablespoon of bleach in 1 gallon of water, mix
and ll airpot with the bleach solution or a commercially
prepared cleaner such as JavaClean3 (Part # 12632).
3. Dispense the bleach solution by pumping through the
nozzle at least 12 full strokes of the pump or lever.
4. Rinse out the bleach solution with hot water several
times, again including pumping out through the nozzle
until the bleach solution has been completely removed.
SUCTION PIPE AND DISCHARGE SPOUT CLEANING
1. Remove the suction pipe assembly.
2. Remove the discharge spout from the suction pipe
assembly.
3. Use a small brush as needed to clean the internal
surfaces of the discharge spout and suction pipe.
1. Remove the lid.
2. Apply pressure to the back of the lid to release the
bottom plate.
3. Downward pressure on the lid release button can
assist in removing the bottom plate.
4. Remove the bottom plate.
5. Remove and disassemble the bellows.
6. Place the bellows in a suitable container and add a
disinfecting cleaning solution to ll the bellows.
7. Allow the bellows to soak in the cleaning solution
for ten minutes. After two minutes, gently squeeze
the bellows and agitate the bellows in the cleaning
solution. Repeat every two minutes.
8. Remove the bellows from the cleaning solution.
The interior surface of the bellows is accessible
through the large hole in one end of the bellows.
9. Rinse the bellows in clean hot water to remove
traces of cleaning solution.
10. If residue remains, insert a household disinfectant
wipe into the large bellow’s hole and hand wipe
the surface. Rinse and repeat as required.
10-9B-77
CARE & HANDLING
RECOMMENDATIONS
1. To open lid,
push lock
release button.
2. Remove suction
pipe without
hitting inside
walls. Before
lling the pot
with hot liquid,
it is advisable
to pre-warm
the inside with
a small amount
of hot water. Fill
with liquid.*
3. Lift lid lever
upwards from
base lid until tab
locks into place.
Press the top
plate to release
contents.
4. After serving,
gently lift the
lever upwards,
then press tab
while lowering
lever to original
closed position.
* For direct brewing, remove lid
by pushing lock release and
place pot under compatible
brewing equipment with suction
pipe in place.
1. Do not overll. If lled to the brim, pot will overow
when pipe is replaced. For glass lined units, do not
look directly into the airpot when lling. Keep the
unit at arms length.
2. For glass liner models, the glass ask can shatter
from mishandling such as sudden, forceful contact
with the lower end of the ow pipe. If a glass lined
unit is dropped, the liner may break. Under no
circumstances should the contents be consumed as
they may contain glass fragments.
3. Do not use a scrub brush, polishing powder, etc., to
clean the inside as these can damage the glass or
stainless surface. Clean only with a soft sponge. Do
not immerse in water. Store with lid off.
4. Place the pot beyond reach of children, especially if
it is lled with a hot liquid.
5. Direct heat from stoves, heaters, replaces or
campres may damage the pot.
6. Do not use chemicals, alcohol, dairy products, ice,
solid foods, sticky products or tea leaves.
7. For glass lined pots, do not stir contents with pipe.
8. Carry by the handle and use this airpot in an upright
position. Avoid tilting, tipping or dropping. This
product is designed for table top use only. It should
not be transported and may leak if placed on its
side.