TX165A 135A,115A TURF FLEX FINISHING MOWER Published 02/11 Part NO. 00777711C OPERATOR’S MANUAL This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. C01Cover RHINO ® 1020 S. Sangamon Ave. Gibson City, IL 60936 800-446-5158 Email: parts@servis-rhino.com © 2011 Alamo Group Inc. $0.
To the Owner/Operator/Dealer All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents. BEFORE YOU START! Read the safety messages on the implement and shown in your manual.
In order to reduce accidents and enhance the safe operation of mowers, Alamo Group Ag Division, in cooperation with other industry manufacturers has developed the AEM/FEMA Industrial and Agricultural Mower Safety Practices video and guide book. The video will familiarize and instruct mower-tractor operators in safe practices when using industrial and agricultural mowing equipment.
Alamo Group Ag.
TABLE OF CONTENTS SAFETY SECTION .............................................................................................................. 1-1 General Safety Instructions and Practices ......................................................................................................... 1-2 Operator Safety Instructions and Practices ....................................................................................................... 1-3 Equipment Operation Safety Instructions and Practices .......
OPERATING THE TRACTOR AND IMPLEMENT .......................................................................................... 4-30 Foreign Debris Hazards ................................................................................................................................... 4-31 Bystander/Passerby Precautions ..................................................................................................................... 4-32 Engaging the Power Take Off (PTO) ................................
SAFETY SECTION Safety Section 1-1 © 2011 Alamo Group Inc.
SAFETY General Safety Instructions and Practices SAFETY A careful operator is the best operator. Safety is of primary importance to the manufacturer and should be to the owner/operator. Most accidents can be avoided by being aware of your equipment, your surroundings, and observing certain precautions. The first section of this manual includes a list of Safety Messages that, if followed, will help protect the operator and bystanders from injury or death.
SAFETY Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the state of California to cause cancer and birth defects or other reproductive harm. (SG-30) Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the state of California to cause cancer, birth defects or other reproductive harm. (SG-31) The rotating parts of this machine continue to rotate even after the PTO has been turned off.
SAFETY SAFETY PROLONGED EXPOSURE TO LOUD NOISE MAY CAUSE PERMANENT HEARING LOSS! Tractors with or without an Implement attached can often be noisy enough to cause permanent hearing loss. We recommend that you always wear hearing protection if the noise in the Operator’s position exceeds 80db. Noise over 85db over an extended period of time will cause severe hearing loss. Noise over 90db adjacent to the Operator over an extended period of time will cause permanent or total hearing loss.
SAFETY Use extreme caution when getting onto the Implement to perform repairs, maintenance and when removing accumulated material. Only stand on solid flat surfaces to ensure good footing. Use a ladder or raised stand to access high spots which cannot be reached from ground level. Slipping and falling can cause serious injury or death. (SG-33) DO NOT operate this Implement on a Tractor that is not properly maintained.
SAFETY Always keep a careful lookout and use extreme care when working around utility and municipal obstructions. Never allow the Mower to contact any utility, municipal, or other type structure. Clearly mark all mowing obstructions and consult local utility providers for a safe code of operation. (SPU-5) SAFETY Do not operate the implement while wearing loose fitting clothing. Entanglement of the clothing with the rotating elements can result in serious injury or even death.
SAFETY There are obvious and hidden potential hazards in the operation of this Mower. REMEMBER! This machine is often operated in weeds and in heavy grass. The Blades of this Mower can throw objects if shields are not properly installed and maintained. Serious injury or even death may occur unless care is taken to insure the safety of the operator, bystanders, or passersby in the area. Do not operate this machine with anyone in the immediate area. Stop mowing if anyone is within 100 yards of mower.
SAFETY Never allow children or other persons to ride on the Tractor or Implement. Falling off can result in serious injury or death. (SG-10) SAFETY Do not mow with two machines in the same area except with Cab tractors with the windows closed. (SGM-11) Do not mount or dismount the Tractor while the tractor is moving. Mount the Tractor only when the Tractor and all moving parts are completelystopped. (SG-12) Start tractor only when properly seated in the Tractor seat.
SAFETY Operate the Tractor and/or Implement controls only while properly seated in the Tractor seat with the seat belt securely fastened around you. Inadvertent movement of the Tractor or Implement may cause serious injury or death. (SG-29) In case of mechanical difficulty during operation, place the transmission in the park position, set the parking brake, shut down all power, including the PTO and the engine and remove the key. Wait until all rotating motion has stopped before dismounting.
SAFETY SAFETY Extreme care should be taken when operating near loose objects such as gravel, rocks, wire, and other debris. Inspect the area before mowing. Foreign objects should be removed from the site to prevent machine damage and/or bodily injury or even death. Any objects that cannot be removed must be clearly marked and carefully avoided by the operator. Stop mowing immediately if blades strike a foreign object.
SAFETY Follow these guidelines to reduce the risk of equipment and grass fires while operating, servicing, and repairing the Mower and Tractor: -Equip the Tractor with a fire extinguisher in an accesible location. -Do Not operate the Mower on a Tractor with an underframe exhaust. -Do Not smoke or have an open flame near the Mower and Tractor. -Do Not drive into burning debris or freshly burnt areas. -Ensure slip clutches are properly adjusted to prevent excessive slippage and plate heating.
SAFETY Rotary Mowers are capable under adverse conditions of throwing objects for great distances (300 feet or more) and causing serious injury or death. Follow safety messages carefully.
SAFETY Always shut the Tractor completely down, place the transmission in park, and set the parking brake before you or anyone else attempts to connect or disconnect the Implement and Tractor hitches. (S3PT-15) Never operate the Tractor and Mower if the Implement input driveline is directly connected to the Tractor transmission.
SAFETY Make certain that the “Slow Moving Vehicle” (SMV) sign is installed in such a way as to be clearly visible and legible. When transporting the Equipment use the Tractor flashing warning lights and follow all local traffic regulations. (SG-6) SAFETY Transport only at speeds where you can maintain control of the equipment. Serious accidents and injuries can result from operating this equipment at high speeds.
SAFETY Maintenance and Service Safety Instructions and Practices Make sure the PTO shield, integral driveline shields, and input shields are installed when using PTO-driven equipment. Always replace any shield if it is damaged or missing. (S3PT-8) Always disconnect the main PTO Driveline from the Tractor before performing service on the Implement. Never work on the Implement with the tractor PTO driveline connected and running.
SAFETY SAFETY Periodically inspect all moving parts for wear and replace when necessary with authorized service parts. Look for loose fasteners, worn or broken parts, and leaky or loose fittings. Make sure all pins have cotter pins and washers. Serious injury may occur from not maintaining this machine in good working order. (SG-21) Do Not fill fuel tank while engine is running. Refuel only after engine has cooled down.
SAFETY DO NOT weld or repair rotating mower components. Welds and other repairs may cause severe vibration and/or component failure resulting in part being thrown from the mower causing serious bodily injury. See your Authorized Dealer for proper repairs. (SGM-13) PARTS INFORMATION Rhino mowers use balanced and matched system components for blade carriers, blades, cuttershafts, knives, knife hangers, rollers, drivetrain components, and bearings. These parts are made and tested to Rhino specifications.
SAFETY SAFETY Decal Location NOTE: Rhino supplies safety decals on this product to promote safe operation. Damage to the decals may occur while in shipping, use, or reconditioning. Rhino cares about the safety of its customers, operators, and bystanders, and will replace the safety decals on this product in the field, free of charge (Some shipping and handling charges may apply). Contact your Rhino dealer to order replacement decals. TX165A,135A,115A 02/11 © 2011 Alamo Group Inc.
SAFETY PART NO. QTY LEVEL DESCRIPTION 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. 35.
SAFETY Decal Description SAFETY DANGER! - Multi Hazard - Failure to follow Safety Messages and Operating Instructions can cause serious bodily injury or even death to Operator and Others in area. P/N 02967827 TX165A,135A,115A 02/11 © 2011 Alamo Group Inc.
SAFETY PELIGRO! Spanish Translation for Driveline Safety Peligro Translation, If you do not know how to read English, please find someone who knows how to read English. P/N 00725746 10 Hour - Lubrication Decal P/N 00755691 Operator's Manual (with repair parts) and warranty was attached to this implement during final inspection. P/N 00763977 TX165A,135A,115A 02/11 © 2011 Alamo Group Inc.
SAFETY For safety and to guarantee optimum product reliability always use genuine RHINO replacement parts. SAFETY P/N 00760657 WARNING! - Guard Missing, Do Not Operate P/N 00775933 RHINO LOGO P/N D301 TX165A,135A,115A 02/11 © 2011 Alamo Group Inc.
SAFETY DANGER! Keep Away Thrown Objects. P/N 00769737 WARNING! Do not operate with Belt Shield removed. Finger(s) may be pinched off if get caught between V-Belt and Pulley. P/N 00758194 INFORMATION - 5 Year Gearbox Warranty 00778611 TX165A,135A,115A 02/11 © 2011 Alamo Group Inc. Safety Section 1-23 SAFETY Inspect the area before mowing for potential mower hazards. Remove or avoid all foreign objects such as wire, cable, metal objects, and all other foreign material.
SAFETY Name Decal -TURF FLEX SAFETY 00763535 DANGER! Keep Away P/N 00755742 DANGER! Make certain that drivelines are correct length and are securely attached. P/N 00756494 DANGER! Guard Missing, Do Not Operate. If you see this decal, Do Not Operate the mower until the shield has been replaced. P/N 00756004 TX165A,135A,115A 02/11 © 2011 Alamo Group Inc.
SAFETY Logo Product Name: Rhino DANGER! Crushing and Pinch Points. Moving machinery parts can pinch or crush or fallwhich may cause injury or death. P/N 02962765 WARNING! Avoid Bodily Injury, Use 540RPM PTO Speed Only. P/N D103 WARNING! Never use your hand to check for oil leaks. Always use paper or cardboard. P/N 00756059 TX165A,135A,115A 02/11 © 2011 Alamo Group Inc.
SAFETY SAFETY WARNING! DO NOT transport at speeds higher than 20 mph. Only transport behind a properly sized and equipped tractor. P/N 00777394 DANGER! Rotating Driveline Keep Away, Contact can cause death. P/N 00756005 IMPORTANT! Required For Suggested for standard shaft. Jackshaft Unit. P/N D102 WARNING! Disengage PTO before folding wings to prevent instant failure of drivelines and possible severe bodily injury or death. 00763536 TX165A,135A,115A 02/11 © 2011 Alamo Group Inc.
SAFETY DANGER! wings. Stay clear when lowering or raising P/N 00753840 P/N 1458392 Amber Reflector. Keep reflectors clean and visible. P/N 1458393 Red Reflectors P/N 2738332 TX165A,135A,115A 02/11 © 2011 Alamo Group Inc. Safety Section 1-27 SAFETY Red Reflector. Keep reflectors clean and visible.
SAFETY Slow Moving Vehicle Decal. Keep SMV reflector clean and visible. DO NOT transport or operate without the SMV. SAFETY P/N 03200347 Read Operator’s Manual! The operator’s manual is located inside this canister. If the manual is missing order one from your dealer. P/N 00776031 WARNING! Jack - Maximum Capacity 1,800 lbs. Side Load 550 lbs. P/N D525 TX165A,135A,115A 02/11 © 2011 Alamo Group Inc.
SAFETY Federal Laws and Regulations This section is intended to explain in broad terms the concept and effect of federal laws and regulations concerning employer and employee equipment operators. This section is not intended as a legal interpretation of the law and should not be considered as such. Employer-Employee Operator Regulations U.S. Public Law 91-596 (The Williams-Steiger Occupational and Health Act of 1970) OSHA Title 29, Code of Federal Regulations Part 1928.57(a)(6). www.osha.
Contents Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety Alerts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 A Word To The User/Operator . . . . . . . . . . . . . . . . . . . . 3 The Industrial/Agricultural Mower. . . . . . . . . . . . . . . . . 4 Follow A Safety Program . . . . . . . . . . . . . . . . . . . . . . . . 5 Prepare For Safe Operation . . . . . . . .
Safety Alerts Symbol Signal Words This Safety Alert Symbol means: “ATTENTION! STAY ALERT! YOUR SAFETY IS INVOLVED!” Signal words are distinctive words that will typically be found on safety signs on the mower and other worksite equipment. These words may also be found in this manual and the manufacturer’s manuals. These words are intended to alert the operator to a hazard and the degree of severity of the hazard.
The Industrial/Agricultural Mower Industrial/Agricultural Mower Types Mowers are used for pasture clipping, crop residue shredding, heavy brush cutting, waterways, right-ofways, roadside or highway mowing. Also, these mowers are used for cutting grass and other growth in public areas such as parks and cemeteries. Flail Boom Rotary Sickle Bar Folding Wing Rotary The Industrial/Agricultural Mower Agricultural Disc Mower Types Disc mowers are designed and equipped to cut hay crops at higher field speed.
Follow A Safety Program Protect Yourself Wear personal protective clothing and Personal Protective Equipment (PPE) issued to you or called for by job conditions. You must ALWAYS wear safety glasses with side shields. You may also need: — Hard hat — Safety shoes — Safety goggles or face shield — Heavy gloves — Hearing protection — Reflective clothing — Wet weather gear — Respirator or filter mask Wear whatever is needed—don’t take chances.
Follow A Safety Program Avoid Injury From Raised Equipment Avoid Injury From High Pressure Fluid Avoid possible crushing injury from falling mower or other raised equipment. Avoid fluid injection injury due to high pressure fluid leaks. Avoid Crushing – Block Up or Securely Support Mower Before working near or under raised mower or equipment parts: — Securely support or block up raised mower or equipment parts according to the operator’s manual.
Follow A Safety Program Be Alert! For Safe Operation Know where to get assistance. Know how to use a first aid kit and fire extinguisher/fire suppression system. You must be a qualified and authorized operator for proper operation of your machine. You must clearly understand the written instructions supplied by the manufacturer, be trained—including actual operation of the mower—and know the safety rules and regulations for the worksite.
Follow A Safety Program Some Rules You Must Work By (continued) Keep Children Away from Equipment — Only qualified and authorized individuals may operate this equipment. — Never allow children to play on, ride on or operate the equipment. Children are not qualified to operate this equipment. — Do not allow any riders. — Use three-point contact (handholds and steps) and face the equipment when mounting or dismounting. — Keep bystanders 300 ft (92 m) from the mowing operation.
Prepare For Safe Operation Check The Mower And Tractor Equipment Before beginning your work day inspect the machine and have all systems in good operational condition. Walk-Around Inspection WARNING! Prevent possible crushing injury from falling equipment. Hydraulic system or part failure could cause unsupported equipment to fall. Do not go under raised equipment unless it is properly supported according to the operator’s manual.
Prepare For Safe Operation Know The Work Area Before you operate the mower thoroughly inspect the work area. Walk around the area and inspect the surfaces you will travel on when using the mower.
Prepare For Safe Operation Tractor And Mower Controls Safety Test Start the tractor following the specific procedures in the manufacturer’s operator’s manual. These procedures normally include: — Fasten and adjust seat belt on your ROPS-equipped tractor. — Check parking brake for engagement. — Check PTO disengagement. — Check all controls for Park position. — Warn others in area before starting tractor. — Start tractor following tractor manufacturer’s recommended starting procedures.
Prepare For Safe Operation Hitching Mower To Tractor Read and Understand Manuals Before Operating Three-point hitch-mounted mowers: — Refer to mower and tractor manufacturers’ manuals. — Place tractor’s hydraulic power lift (rockshaft) selector lever in down position to avoid unexpected movement. — Explain the hitching procedures to those operators who cannot read. — Front-end weights may be needed to maintain steering control and front-end stability. Refer to the manufacturers' operator's manual(s).
Start Safely Make The Right Start Mow only in daylight or good artificial light conditions. Avoid serious injury or death from mower-thrown objects or blade contact: — Keep chain shields, flexible or solid deflector shields or discharge chutes in place and in good repair. — Keep bystanders at least 300 ft (92 m) from mowing operation. — Never direct mower discharge toward anyone. — Keep hands, feet and other body parts away from rotating parts, blades and discharge openings.
Operate Safely Mower-Thrown Objects (continued) Disc Mowers — When using a disc mower it is important to know the area to be mowed. If the operator has mowed the field before and is familiar with all obstacles that may be present, it is sufficient to watch ahead of the mower path for any additional objects that may have entered the field. Be ready to stop or avoid any objects that could be hazardous if thrown by the mower.
Operate Safely Under Mount Mower Safety Practices When mowing with an under mount mower: — Keep removable discharge chute in place and over discharge opening. — Never stand on a mower housing when the tractor engine is operating. — Distribute grass clippings with discharge chute facing mowed area. — Before clearing a clogged mower or discharge chute, shut down your machine using proper equipment shut down practice. (See page 18, Proper Equipment Shut Down Practices.
Operate Safely Wing And Side Mount Mowers Safety Practices Raised wing positions reduce shielding protection and increases the thrown object and blade contact hazard risks. Avoid possible serious injury or death by thrown objects or blade contact from raising and lowering wings during mowing operations: — Do not mow with bystanders within 300 ft (92 m) of the mower. — Be sure no one is near mower while raising or lowering wings.
Operate Safely Uneven Terrain Mowing Safety Practices (continued) Maintain Control, Use Low Speeds — Use extreme care to maintain control over the equipment when operating in these conditions. — Increase tractor stability by adding wheel weights, ballast and increasing wheel spacing to maximum. Refer to operator’s manual for recommendations. — Maintain minimum ground speed. — Make wide and gradual turns. — Avoid sudden starts, stops, and turns when operating up, down, or across slopes.
Park Safely Parking Safety Practices — Use designated or out-of-traffic areas. — Use firm level ground locations. — Set parking brake. — Lower raised equipment to ground. P Shut down the mower and tractor using proper equipment shut down practice before dismounting tractor. (See page 18, Proper Equipment Shut Down Practices.) Set Parking Brake Lower Raised Equipment to Ground Sloping ground parking locations: — Position equipment across slope. — Set parking brakes. — Lower raised equipment to ground.
Shut Down Safely Dismounting Properly — Never dismount from moving equipment. — Never jump from any machines. — Dismount carefully. — Check for slippery steps. — Keep feet and hands away from controls. — Use handholds and steps during dismount. — Face machine and use three-point contact (2 hands and 1 foot or 2 feet and 1 hand).
Perform Maintenance Safely Prepare Yourself Wear personal protective clothing and Personal Protective Equipment (PPE) issued to you or called for by job conditions. You must ALWAYS wear safety glasses with side shields. You may also need: — Hard hat — Safety shoes — Safety glasses, goggles or face shield — Apron and gloves — Hearing protection — Welding helmet or goggles — Respirator or filter mask Wear whatever is needed—don’t take chances.
Perform Maintenance Safely Prepare The Machine Stored energy sources (electrical, mechanical, hydraulic, pneumatic, chemical, thermal, etc.) must be controlled or reduced to a practical minimum before performing any maintenance, repair or service procedures. Safety practices to prevent potential injuries from energy-releasing sources: — Disengage PTO before shutting off engine. — Place controls in PARK or NEUTRAL before shutting off engine. — Set parking brake or block wheels.
Perform Maintenance Safely Use Proper Ventilation If it is necessary to run an engine in an enclosed area, remove the exhaust fumes from the area with an exhaust pipe extension. If you do not have an exhaust pipe extension, make sure you open the doors and get outside air into the area. WARNING! Prevent possible injury. Never work on machinery with the engine running unless instructed by the manufacturer’s manuals for specific service.
Perform Maintenance Safely Hydraulic System Hazards The hydraulic system is under pressure whenever the engine is operating and may hold pressure even after the engine is shut off. Cycle all hydraulic controls including the auxiliary hydraulic control after the engine is shut down. Relieve trapped pressure in the lines after the attachments are shut down and resting on the ground. During inspection of the hydraulic system: — Wait for fluid to cool before disconnecting the lines.
Perform Maintenance Safely Avoid Explosion WARNING! Avoid possible serious injury from explosion. Lead-acid batteries produce extremely explosive gases especially when being charged. Keep arcs, sparks, flames and lighted tobacco away. — Do not smoke near batteries. — Keep arcs, sparks and open flames away from batteries. — Provide adequate ventilation. Never check the battery by placing a metal object across the battery posts — the resulting spark could cause an explosion.
Perform Maintenance Safely Tire And Wheel Maintenance (continued) WARNING! The types of wheels and tires usually found on this equipment require special care when servicing to prevent death or serious injury. Do not inflate the tires above the recommended pressure. Be sure to replace tire ballast if equipped. See manufacturer’s specifications for ballast requirements. Keep wheel lug nuts tightened to manufacturer’s recommendations. Never cut or weld on a wheel with an inflated tire mounted on it.
Perform Maintenance Safely Mower Blade Maintenance (continued) — How are mower blades made? Mower blades are made of high strength alloy spring steel. They are hot-forged and shaped to meet the manufacturer’s individual specifications, then heat treated and tempered to a high strength, ductile state to reduce the possibility of breaking while mowing. Blades are tested to ensure they meet strength, hardness, and ductility standards.
Contenido Reconocimiento . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Introducción . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Alertas de seguridad . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Palabras para el usuario/operador . . . . . . . . . . . . . . . . 3 Cortadora de césped industrial/para agricultura . . . . 4 Cumplimiento del programa de seguridad . . . . . . . . . 5 Preparación para una operación segura . . . . . . . . . . .
Alertas de seguridad Símbolo Palabras indicativas Este símbolo de alerta de seguridad significa: “¡ATENCIÓN! ¡MANTÉNGASE ALERTA! ¡SU SEGURIDAD ESTÁ EN RIESGO!” Las palabras indicativas son palabras distintivas que típicamente se encontrarán en letreros de seguridad de la cortadora de césped y otros equipos del sitio de trabajo. Estas palabras también se pueden encontrar en este manual y en los manuales del fabricante.
Cortadora de césped industrial/para agricultura Tipos de cortadora de césped industrial/para agricultura Las cortadoras de césped se usan para recortar pasturas, desmenuzar residuos de cultivos, cortar arbustos, realizar desbroce pesado, cortar la hierba en vías de agua, derechos de paso, costados de caminos o autopistas. Además, estas cortadoras se usan para cortar la hierba y otras plantas en zonas públicas como parques y cementerios.
Cumplimiento del programa de seguridad Protéjase a sí mismo Use la ropa de protección personal y los equipos de protección personal (PPE) que se le proporcionen o que requieran las condiciones del trabajo. SIEMPRE debe usar gafas de seguridad con escudos laterales.
Cumplimiento del programa de seguridad Evite las lesiones provocadas por equipos elevados Evite posibles lesiones de aplastamiento por caídas de la cortadora u otros equipos elevados. Evite ser aplastado – Bloquee o apoye con seguridad la cortadora Antes de trabajar cerca o debajo de partes levadas de la cortadora o de los equipos: — Apoye o bloquee con seguridad las partes elevadas de la cortadora o los equipos de acuerdo con el manual del operador.
Cumplimiento del programa de seguridad ¡Manténgase alerta! Para una operación segura Sepa dónde obtener asistencia. Sepa cómo usar un equipo de primeros auxilios y un extintor de incendios/ sistema de supresión de fuego. Usted debe ser un operador cualificado y autorizado para operar la máquina correctamente.
Cumplimiento del programa de seguridad Algunas reglas que debe cumplir al trabajar (continuación) — Únicamente personas cualificadas y autorizadas pueden manejar estos equipos. — Nunca permita que los niños jueguen en los equipos, viajen en ellos o los hagan funcionar. Los niños no están cualificados para manejar estos equipos. — No transporte pasajeros. — Use contacto en tres puntos (asideros y peldaños) y enfrente el equipo al ascender o descender de él.
Preparación para una operación segura Revise los equipos de la cortadora de césped y el tractor Antes de comenzar la jornada de trabajo, inspeccione la máquina y asegúrese de que todos los sistemas estén en buenas condiciones operacionales. ¡ADVERTENCIA! Evite posibles lesiones por aplastamiento producidas por equipos que caen. La falla del sistema hidráulico o de una parte podría causar la caída de equipos que no están apoyados.
Preparación para una operación segura Familiarícese con la zona de trabajo Antes de hacer funcionar la cortadora de césped, inspeccione cuidadosamente la zona de trabajo. Recorra a pie alrededor de la zona e inspeccione las superficies sobre las cuales se desplazará cuando utilice la cortadora.
Preparación para una operación segura Prueba de seguridad de los controles del tractor y de la cortadora de césped Arranque el tractor siguiendo los procedimientos específicos del manual del operador del fabricante. Estos procedimientos normalmente incluyen: — Colóquese y ajústese el cinturón de seguridad en el tractor equipado con ROPS. — Verifique que el freno de estacionamiento esté aplicado. — Verifique que la TDF esté desenganchada.
Preparación para una operación segura Enganche de la cortadora de césped al tractor Lea y asegúrese de comprender los manuales antes de comenzar la operación Cortadoras montadas en enganche de tres puntos: — Consulte los manuales de los fabricantes de la cortadora y del tractor. — Coloque la palanca selectora de elevación de potencia hidráulica del tractor en la posición descendida para evitar movimientos imprevistos. — Explique los procedimientos de enganche a los operadores que no puedan leerlos.
Arranque con seguridad Cómo realizar un arranque correcto Corte la hierba únicamente con luz diurna o en condiciones de buena luz artificial. Evite lesiones graves o muerte producidas por objetos arrojados por la cortadora o por el contacto con las hojas: — Mantenga los escudos de las cadenas, los escudos deflectores flexibles o sólidos y las rampas de descarga en su lugar y en buen estado de reparación. — Mantenga a las personas ajenas a 300 pies (92 m) de la operación de corte.
Operación con seguridad Objetos arrojados por la cortadora de césped (continuación) Apague la TDF, espere que las hojas dejen de girar, eleve la cortadora y, después, retroceda. Cortadoras de disco — Cuando se usa una cortadora de disco, es importante conocer la zona donde se va a cortar.
Operación con seguridad Prácticas de seguridad para la cortadora de césped de montaje inferior Cuando se traslada con una cortadora de césped de montaje inferior: — Mantenga la rampa de descarga extraíble en su lugar y por encima de la abertura de descarga. — Nunca se pare sobre la carcasa de una cortadora de césped cuando el motor del tractor está en funcionamiento. — Distribuya los recortes de hierba con la rampa de descarga orientada hacia la zona donde se cortó.
Operación con seguridad Prácticas de seguridad para cortadoras de césped con laterales y montaje lateral 300 ft (92 m) Las posiciones elevadas de los laterales reducen la protección de los escudos y aumentan los riesgos de objetos arrojados y contacto con las hojas.
Operación con seguridad Prácticas de seguridad para trabajos de corte en terrenos desparejos (continuación) — Use extremo cuidado para mantener el control de los equipos cuando trabaja en estas condiciones. — Aumente la estabilidad del tractor agregando pesos o lastre en las ruedas y aumentando al máximo la separación entre las ruedas. Consulte las recomendaciones en el manual del operador. — Mantenga la velocidad de desplazamiento en el mínimo. — Realice giros amplios y graduales.
Estacionamiento seguro Prácticas de seguridad para el estacionamiento — Use las zonas designadas o alejadas del tránsito. — Use lugares con suelo firme y nivelado. — Aplique el freno de estacionamiento. — Descienda el equipo de la cortadora de césped hasta el suelo. P Apague la cortadora y el tractor usando la práctica correcta de apagado de equipos antes de descender del tractor. (Consulte la página 18, Prácticas correctas de apagado de los equipos.
Apagado con seguridad Descenso correcto — Nunca descienda de equipos en movimiento. — Nunca baje de una máquina saltando. — Descienda con cuidado. — Verifique que no haya peldaños resbaladizos. — Mantenga los pies y las manos lejos de los controles. — Use los asideros y los peldaños durante el descenso. — Enfrente la máquina y use contacto de tres puntos (2 manos y 1 pie o 2 pies y 1 mano).
Realización de mantenimiento con seguridad Preparación personal Use la ropa de protección personal y los equipos de protección personal (PPE) que se le proporcionen o que requieran las condiciones del trabajo. SIEMPRE debe usar gafas de seguridad con escudos laterales.
Realización de mantenimiento con seguridad Preparación de la máquina Deben controlarse o reducirse las fuentes de energía almacenada (eléctricas, mecánicas, hidráulicas, neumáticas, químicas, térmicas, etc.) al mínimo practicable antes de realizar cualquier procedimiento de mantenimiento, reparación o servicio. Prácticas de seguridad para prevenir posibles lesiones por fuentes que liberan energía: — Desenganche la TDF antes de apagar el motor.
Realización de mantenimiento con seguridad Use ventilación adecuada Si es necesario hacer funcionar un motor en una zona cerrada, elimine del área las emanaciones de escape con una extensión del caño de escape. Si no tiene esa extensión, asegúrese de abrir las puertas y dejar entrar aire del exterior. ¡ADVERTENCIA! Evite posibles lesiones. Nunca trabaje en la maquinaria con el motor en funcionamiento salvo que así lo indiquen los manuales del fabricante para un servicio en particular.
Realización de mantenimiento con seguridad Riesgos del sistema hidráulico El sistema hidráulico se encuentra bajo presión siempre que el motor está funcionando; puede conservar presión incluso después de apagar el motor. Haga funcionar todos los controles hidráulicos incluyendo el control hidráulico auxiliar después de que el motor esté apagado. Alivie la presión atrapada en las líneas después de que los accesorios están apagados y apoyados en el suelo.
Realización de mantenimiento con seguridad Evite explosiones ¡ADVERTENCIA! Evite posibles lesiones graves por explosiones. Las baterías de plomo-ácido producen gases sumamente explosivos, especialmente durante la carga. Mantenga alejados los arcos, las chispas, las llamas y el tabaco encendido. — No fume cerca de las baterías. — Mantenga los arcos, las chispas y llamas abiertas alejadas de las baterías. — Proporcione ventilación adecuada.
Realización de mantenimiento con seguridad Mantenimiento de neumáticos y ruedas (continuación) ¡ADVERTENCIA! Los tipos de ruedas y neumáticos que generalmente se encuentran en estos equipos requieren cuidados especiales al realizar servicios para evitar lesiones graves o la muerte. No infle los neumáticos por encima de la presión recomendada. Asegúrese de volver a colocar el lastre de los neumáticos si está instalado. Consulte las especificaciones del fabricante para ver los requisitos de lastre.
Realización de mantenimiento con seguridad Mantenimiento de las hojas de la cortadora (continuación) — ¿Cómo están hechas las hojas de la cortadora de césped? Están hechas acero para resortes de aleación de alta resistencia. Se forjan en caliente y se les da forma para cumplir con las especificaciones individuales del fabricante; luego, se tratan y templan a un estado dúctil, de alta resistencia para reducir la posibilidad de rupturas durante el corte.
INTRODUCTION SECTION Introduction Section 2-1 © 2011 Alamo Group Inc.
INTRODUCTION INTRODUCTION This Rotary Mower is designed with care and built with quality materials by skilled workers. Proper assembly, maintenance, and operating practices, as described in this manual, will help the owner/operator get years of satisfactory service from the machine. The purpose of this manual is to familiarize and instruct. The Assembly Section instructs the owner/operator in the correct assembly of the Mower using standard and optional equipment.
INTRODUCTION INTRODUCTION The Turf Flex is designed for light-duty cutting such as lawn maintenance plus small weed and grass control. With a reasonable amount of preventive maintenance, the mower will provide years of dependable service. NEVER ALLOW CHILDREN TO OPERATE, RIDE ON, OR COME CLOSE TO MOWER OR TRACTOR.
INTRODUCTION Attention Owner/Operator BEFORE OPERATING THIS MACHINE: 1. Carefully read the Operator’s Manual, completely understand the Safety Messages and instructions, and know how to operate correctly both the tractor and implement. INTRODUCTION 2. Fill out the Warranty Card in full. Be sure to answer all questions, including the Serial Number of the implement. Mail within 30 days of delivery date of this implement.
ASSEMBLY SECTION Assembly Section 3-1 © 2011 Alamo Group Inc.
ASSEMBLY Operating with PTO speed over 540 RPM can cause excessive vibration with subsequent machine failure which can cause serious injury or even death. Never exceed 600 RPM. DEALER SET-UP INSTRUCTIONS ASSEMBLY This mower is shipped completely assembled from the factory. Always use personal protection devices such as eye and ear protectors during assembly. TX165A,135A,115A 02/11 © 2011 Alamo Group Inc.
OPERATION SECTION Operation Section 4-1 © 2011 Alamo Group Inc.
OPERATION RHINO TX165A,135A,115A TURF FLEX ROTARY MOWER OPERATION INSTRUCTIONS OPERATION Rhino TURF FLEX mowers are manufactured with quality material by skilled workers. These mowers are designed for cutting grass and small weeds. The mower is equipped with protective deflectors and/or chain guards to prevent objects being thrown from the mower by the blades, however, no shielding is 100% effective.
OPERATION 1.
OPERATION 2. OPERATOR REQUIREMENTS OPERATION Safe operation of the unit is the responsibility of a qualified operator. A qualified operator has read and understands the implement and tractor Operator’s Manuals and is experienced in implement and tractor operation and all associated safety practices. In addition to the safety messages contained in this manual, safety signs are affixed to the implement and tractor.
OPERATION mower with a tractor that does not meet the following requirements may cause tractor or mower damage and be a potential danger to the operator and passersby. Tractor Requirements and Capabilities • • • • 2.1 ROPS and Seat Belt The tractor must be equipped with a Roll-Over-Protective-Structure (ROPS) (tractor cab or roll-bar) and seat belt to protect the operator from falling off the tractor, especially during a roll over where the driver could be crushed and killed.
OPERATION 2.4 Drawbar The tractor drawbar must be positioned at a certain length based on the operating speed of the mower to ensure proper driveline operation. 540 RPM mowers require the drawbar length measured from shaft end to hitch pin hole to be positioned at 14”. OPERATION Ensure the drawbar is rated to carry the tongue weight of the mower. 2.5 Tractor Hydraulics The mower is raised and lowered with three hydraulic cylinders, one for each section.
OPERATION DO NOT use a PTO adapter to attach a non-matching Implement driveline to a Tractor PTO. Use of an adapter can double the operating speed of the Implement resulting in excessive vibration, thrown objects, and blade and implement failure. Adapter use will also change the working length of the driveline exposing unshielded driveline areas. Serious bodily injury and/or equipment failure can result from using a PTO adapter.
OPERATION Never allow children or other persons to ride on the Tractor or Implement. Falling off can result in serious injury or death. (SG-10) OPERATION 3.2 Dismounting the Tractor Before dismounting, park the tractor and implement on a reasonably level surface, apply the parking brake, idle the engine down, disengage the PTO, and lower the implement to the ground. Shut down the tractor engine according to the operator’s manual, remove the key, and wait for all motion to completely stop.
OPERATION 4. STARTING THE TRACTOR The operator must have a complete understanding of the placement, function, and operational use of all tractor controls before starting the tractor. Review the tractor operator’s manual and consult an authorized dealer for tractor operation instructions if needed. Before starting the tractor ensure the following: • Conduct all pre-start operation inspection and service according to the tractor operator’s manual.
OPERATION Always shut the Tractor completely down, place the transmission in park, and set the parking brake before you or anyone else attempts to connect or disconnect the Implement and Tractor hitches. (S3PT-15) OPERATION 5.1 Connecting the Mower Tongue to the Tractor 1. The tractor must be equipped to operate at 540 RPM PTO speed and the drawbar length at 14”. 2. Using the parking jac, position the tongue clevis to the height of the tractor drawbar. 3. Board the tractor and start the engine.
OPERATION 5.3 Connecting Mower Hydraulics 1. Hydraulic Cylinder Priming Hydraulic Cylinders must be filled with hydraulic oil before releasing the wing transport locks to lower the mower. Hydraulic cylinders and lines are filled by holding the valve control levers in the raised position until the cylinders fully extend then place the control lever in the float position.
OPERATION Never work under the Implement, the framework, or any lifted component unless the Implement is securely supported or blocked up to prevent sudden or inadvertent falling which could cause serious injury or even death. (SG-14) OPERATION 6.1 Cutting Height Adjustment 1. Using the tractor hydraulics, raise the mowers off the ground and support under it with secure blocking so not to let the mower drift down during maintenance. 2.
OPERATION 7. DRIVELINE ATTACHMENT The driveline yoke and tractor PTO shaft must be dirt free and greased for attachment. When attaching the Implement input driveline to the Tractor PTO, it is important that the connecting yoke spring activated locking collar slides freely and the locking balls are seated securely in the groove on the Tractor PTO shaft. Push and pull the driveline back and forth several times to ensure it is securely attached.
OPERATION “Bottoming Out” Check Procedure • • OPERATION • • Disconnect driveline from the tractor and slide the profiles together until fully compressed. Place a mark on the inner shield 1/8” from the end of the outer shield and reattach the driveline to the PTO shaft. With the PTO NOT TURNING, slowly drive the tractor with mower attached through the sharpest turn possible and watch shaft movement.
OPERATION 7.2 Constant Velocity (CV) Driveline For mowers equipped with a Constant Velocity (CV) driveline, the maximum turning angle between the tractor and mower must be determined to ensure the joint angle does not over-extend which can cause CV joint damage. Constant Velocity joints enable the driveline to operate smoothly with no vibrations and clattering at angles up to 70°. Angles greater than 80° can result in mechanical damage to the CV joint and mower driveline.
OPERATION Do not turn so sharp or lift mower so high to produce a severe "knocking" of the Driveline which will cause accelerated wear and breakage of drive train components and could result in possible injury from the separated Driveline sections. (SRM-04) OPERATION 8. PRE-OPERATION INSPECTION AND SERVICE Before each use, a pre-operation inspection and service of the implement and tractor must be performed.
OPERATION 8.1 Tractor Pre-Operation Inspection/Service Refer to the tractor operator’s manual to ensure a complete pre-operation inspection and scheduled service is performed according to the manufacturers recommendations.
OPERATION • • • OPERATION • • • • • • • Check that the main driveline securely attached to the tractor and the locking collar is seated in the groove of the PTO Shaft. Ensure wing drivelines are secure at both ends. Ensure the mower hitch is securely attached to the tractor drawbar with a proper size bolt and secured nut. Ensure that a properly rated safety tow chain is equipped securing the mower to the tractor.
OPERATION • • • • • • Inspect cutter knives and knife pins for looseness and excessive wear. Make sure the mower is securely blocked up before crawling beneath. Replace damaged, worn, and missing knives as complete sets to maintain cuttershaft balance. Remove any grass or other debris which may be wrapped around the cuttershafts. Inspect the condition of deck skid shoes and hardware. OPS-R-0050 Ensure each hydraulic cylinder is installed and retained correctly.
OPERATION • OPERATION • • Inspect mower tire condition, wheel bearings, and lug nut torque. Check the condition of the wing hinge pins. Check all the overall condition of the mower main frame. OPS-R-0051 All Safety Shields, Guards and Safety devices including (but not limited to) - the Deflectors, Chain Guards, Steel Guards, Gearbox Shields, PTO integral shields, and Retractable Door Shields should be used and maintained in good working condition.
OPERATION 8.3 Cutting Component Inspection Inspect blade pan and blade assembly for the following: OPERATION OPS-U-0031 Inspect the Blades daily for abnormal wear. REPLACE BOTH BLADES on that carrier IMMEDIATELY if either blade has: • • • • • Become bent or deformed from it’s original shape or Any cracks are visible, or Deep gouges in the blade’s surface are present, or Gouges or chipped areas in the cutting edge are larger than 1/2”(12.
OPERATION 8.4 Blade Bolt Inspection OPERATION Inspect Blade Bolt Head daily for wear as followed: Inspect the Blade Bolt Heads daily for abnormal wear. REPLACE BOTH BLADE BOLTS on the Blades IMMEDIATELY if either blade bolts has: • Visible cracks or • If the recessed area on blade bolt is worn off or • If Blade Bolt has gouges or chipped areas.
OPERATION Finish Mower PRE-OPERATION Inspection Mower ID#________________________Make____________________ Date:_____________________________Shift____________________ Condition at Start of Shift Item Specific Comments if not O.K.
OPERATION OPERATION Tractor PRE-OPERATION Inspection Tractor ID#________________ Make ____________________ Date: Shift ________________ ____________________ Before conducting the inspection, make sure the tractor engine is off, all rotation has stopped and the tractor is in park with the parking brake engaged. Make sure the mower is resting on the ground or securely blocked up and all hydraulic pressure has been relieved. Condition at Start of Shift Item Specific Comments if not O.K.
OPERATION 9. DRIVING THE TRACTOR AND IMPLEMENT Safe tractor transport requires the operator possess a thorough knowledge of the model being operated and precautions to take while driving with an attached implement. Ensure the tractor has the capacity to handle the weight of the implement and the tractor operating controls are set for safe transport. To ensure safety while driving the tractor with an attached implement, review the following.
OPERATION 9.1 Starting the Tractor OPERATION The procedure to start the tractor is model specific. Refer to the tractor operator’s manual for starting procedures for your particular tractor. Consult an authorized dealer if the starting procedure is unclear. Ensure the 3-point control lever is in the lowered position and the PTO is disengaged before starting the tractor. OPS-U-0033 9.2 Brake and Differential Lock Setting Make sure the tractor brakes are in good operating condition.
OPERATION 9.3 Raising the Mower The mower’s center of gravity is raised and the mower more prone to tipping when the wings are in the raised position. Use extreme caution when towing the mower in the transport position and avoid uneven terrain which could upset the mower. OPS-R-0016_D 1. 2. Raise wings to full height. Make certain that lock tab engages into lock bar. 3. Raise center section TX165A,135A,115A 02/11 © 2011 Alamo Group Inc.
OPERATION 9.4 Operating Position OPERATION To lower the mower, retract the hydraulic cylinders to remove tension from the transport locks. Then pull the release rope and place the hydraulic control lever in the float detent to lower the mower. The mower must be operated with the cutter sections fully lowered and the hydraulic control lever in the float detent to ensure the mower follows the contour of the ground and to prevent sections from creeping up.
OPERATION 9.6 Crossing Ditches and Steep Inclines Damage resulting from over-collapse of the driveline’s inner profile and its outer housing may allow the driveline to come loose from the Tractor which could cause bodily injury to the operator or bystanders and/or extensive damage to the Tractor or Implement. OPS-R-0020 When confronted with an incline or ditch, do not approach from an angle which is perpendicular or straight on as damage to or over-collapse of the driveline may occur.
OPERATION OPERATION Inclines and ditches should be approached along a line which is at an angle as shown. This type of path will reduce the possibility of over-collapse of the driveline and resulting damage. If the gradient is so steep that such an approach increases the possibility of a tractor roll-over, select an alternate crossing path.
OPERATION Many varied objects, such as wire, cable, rope, or chains, can become entangled in the operating parts of the mower head. These items could then swing outside the housing at greater velocities than the blades. Such a situation is extremely hazardous and could result in serious injury or even death. Inspect the cutting area for such objects before mowing. Remove any like object from the site. Never allow the cutting blades to contact such items.
OPERATION 10.2 Bystander/Passerby Precautions If a bystander comes within 100 yards of the tractor while the mower is being operated, stop the tractor at once, idle the engine and disengage the PTO. Do not engage the PTO again until all bystanders are well past the 100 yard distance. Rotary Mowers are capable under adverse conditions of throwing objects for great distances (300 feet or more) and causing serious injury or death. Follow safety messages carefully.
OPERATION Do not put hands or feet under mower decks. Blade Contact can result in serious injury or even death. Stay away until all motion has stopped and the decks are securely blocked up. (SGM-09) 10.4 PTO RPM and Ground Speed Ground speed is achieved by transmission gear selection and not by the engine operating speed.
OPERATION OPERATION Do not mow with two machines in the same area except with Cab tractors with the windows closed. (SGM-11) Mow only in conditions where you have clear visibility in daylight or with adequate artificial lighting. Never mow in darkness or foggy conditions where you cannot clearly see at least 300 feet (90 m) in front and to the sides of the tractor and mower.
OPERATION Large, dense, or wet vegetation may need to be mowed in two or more passes to achieve a uniform cut. In such conditions, raise the cutting height to 12” or more on the first pass. OPS-R-0043 TX165A,135A,115A 02/11 © 2011 Alamo Group Inc. Operation Section 4-35 OPERATION Then lower the mower to the desired height and mow the vegetation a second time. If possible, select a mowing pattern that is at a 90 degree angle to the first pass to reduce streaking for a more uniform cut.
OPERATION 10.6 Shutting Down the Implement OPERATION To shut down attached mower head, first bring the tractor to a complete stop. Decrease engine RPM to idle then disengage cutterhead. The mower head will come to a complete stop within a suitable amount of time. Do not engage or disengage the cutterheads at a high RPM unless there is an emergency situation.
OPERATION 11. DISCONNECTING THE MOWER FROM THE TRACTOR Always shut the Tractor completely down, place the transmission in park, and set the parking brake before you or anyone else attempts to connect or disconnect the Implement and Tractor hitches. (S3PT-15) Before disconnecting the mower, the PTO must be disengaged and all motion at a complete stop. Move the mower to a level storage location and lower the center section and both wings to the ground.
OPERATION 12. MOWER STORAGE It is recommended that the mower be stored with the center section and both wings fully lowered to ground level. If the mower is stored with the wings in the raised position, select a level area and install wing transport braces to prevent the wings from falling BEFORE disconnecting the mower hitch from the tractor. Properly preparing and storing the mower at the end of the season is critical to maintaining its appearance and to help ensure years of dependable service.
OPERATION 13. TRANSPORTING THE TRACTOR AND IMPLEMENT Inherent hazards of operating the tractor and implement and the possibility of accidents are not left behind when you finish working in an area. Therefore, the operator must employ good judgement and safe operation practices when transporting the tractor and implement between locations. By using good judgement and following safe transport procedures, the possibility of accidents while moving between locations can be substantially minimized.
OPERATION 13.1 Transporting on Public Roadways OPERATION Extreme caution should be used when transporting the tractor and implement on public roadways. The tractor must be equipped with all required safety warning features including a SMV emblem and flashing warning lights to alert drivers of the tractor’s presence. Remember that roadways are primarily designed for automotive drivers and most drivers will not be looking out for you, therefore, you must look out for them.
OPERATION Make sure that all tractor flashing warning lights, headlights, and brake/tail lights are functioning properly before proceeding onto public roads. While newer model tractors have plenty of lighting to provide warning signals and operating lighting, most older models are only equipped with operating lights. Consult an authorized tractor dealer for lighting kits and modifications available to upgrade the lighting on older tractor models.
OPERATION 13.2 Hauling the Tractor and Implement OPERATION Before transporting a loaded tractor and implement, measure the height and width dimensions and gross weight of the complete loaded unit. Ensure that the load will be in compliance with the legal limits set for the areas that will be traveled through. OPS-U- 0024 Use adequately sized and rated trailers and equipment to transport the tractor and implement. Consult an authorized dealer to determine the proper equipment required.
OPERATION 14. TROUBLESHOOTING GUIDE POSSIBLE CAUSE POSSIBLE REMEDY Streaking Slow Blade Speed Worn Blade Tips Operate PTO at 540 RPM. Replace with Genuine RHINO blades. See your Rhino dealer. Sharpen blades uniformly. Slow ground speed of tractor but keep engine running at full PTO RPM. Cutting slower will help. Slow down until cured. Tighten per Instructions. Apply belt dressing or replace with special RHINO belt. Tighten blade bolt securely. (Note: Left hand threads Torque to 150 ft./lbs.
OPERATION PROBLEM POSSIBLE CAUSE POSSIBLE REMEDY Heavy Vibration Too high blade speed Broken/bent Blade Do not exceed 540 PTO RPM. Replace with genuine RHINO blades. See your RHINO dealer. Grind uniformly, rebalance and replace Replace parts. Clean off Blade.
OPERATION PROBLEM POSSIBLE CAUSE POSSIBLE REMEDY Belt Rollover Pulley misalignment Damaged belt Foreign object in pulley grooves Re-align Replace belt Inspect all pulley grooves for rust, paint or weld spots and remove. Replace pulley Worn pulley groove Rollover, high shock loads or installation damage Replace belt. Belt Breakage High shock loads Avoid abusive mowing. Avoid hitting the ground or large obstructions. Belt came off drive Check drive alignment for foreign material in grooves.
MAINTENANCE SECTION Maintenance Section 5-1 © 2011 Alamo Group Inc.
MAINTENANCE Before operating your Rotary Cutter, make sure it is properly lubricated and thoroughly inspected. Only a minimum of time and effort is required to regularly lubricate and maintain this machine to provide long life and trouble free operation. Always disengage the PTO before raising the Rotary Cutter for transporting or making adjustments. MAINTENANCE LUBRICATION INFORMATION Do not let excess grease collect on or around parts, particularly when operating in sandy areas.
MAINTENANCE GEARBOX The Gearbox has been filled with lubricant to the Test Plug Level prior to shipment. However, you should check the oil level at Test Plug before operating, and frequently thereafter. The gearbox should not require additional lubricant unless the box is cracked or a seal is leaking. It is recommended that the oil level plug be removed after every 8 to 10 hours of operation and oil added until it comes to proper level on dipstick. MntP-R-0054.
MAINTENANCE CENTER 4-WAY GEAR BOX MAINTENANCE Gearbox is filled from factory with proper lube level. To check oil level remote test plug on front side gear. It is recommended that oil level plug be removed every 100 hours of operation and oil added until it runs out test plug hole. The test plug is located in front cap of gearbox. Fill plug is on top of gearbox. Recommended lubricant is Multi-Purpose Gear Oil (P/N 00786250). Gearbox capacity is 2-1/8 Quarts.
MAINTENANCE GAUGE WHEEL ASSEMBLIES Gauge wheels are equipped with bushings which require grease daily. Grease fittings are provided in the Wheel Hub and Gauge Wheel Pivot. Grease after 8 hours of use. MAINTENANCE BLADE SPINDLE LUBRICATION Blade spindles must be lubricated daily (every 8 hrs). Access lubrication fitting through hole in outer shields and in center gearbox mounting. Each spindle must be lubricated enough each time to force small amount of grease out through top seal.
MAINTENANCE MAINTENANCE DRIVELINE LUBRICATION The Drivelines and U-Joints should be inspected each morning before the mower is started. Mnt-0024. The U-Joint and CV Joint on the Driveline undergo extreme forces when the unit is turning or when the Wings are being raised. It is important that the U-Joints and CV Joint be greased each day before the unit is started, and after each 8 hours of use. The U-Joints are located at each end of the Center and Wing Drivelines.
MAINTENANCE CV DRIVELINE PROFILE LUBRICATION Grease telescoping profile tube through slots in shield tubes. NOTE: If slots do not align, cut another slot in outer shield that will align with hole in inner shield. MAINTENANCE WING DRIVELINE PROFILE LUBRICATION Grease Fittings are located on the Cross Assembly of each U-Joint and on the telescoping tubes. Grease the U-Joint after each 8 hours of use. Do not force grease through the Needle Cup Assemblies. Grease the telescoping tubes after 8 hours of use.
MAINTENANCE MAINTENANCE SLIP CLUTCH A slip clutch is incorporated in the PTO drivelin. It is designed to slip, absorb the shock load, and protect the driveline. This clutch has a single disc spring with 6 adjusting nuts. After the first hour of operation, the slip clutch should be checked for overheating. After this first check, the slip clutch should be checked weekly or anytime there is overheating.
MAINTENANCE SEASONAL CLUTCH MAINTENANCE BLADE SERVICING Inspect blades before each use to determine that they are properly installed and in good condition. Replace any blade that is bent, excessively nicked, worn, or has any other damage. Small nicks can be ground out when sharpening. Use only original equipment blades on this cutter. They are made of special heat-treated alloy steel. Substitute blades may not meet specifications and may fail in a hazardous manner that could cause injury.
MAINTENANCE BLADE INSTALLATION Install washer on blade bolt, insert bolt into blade, thread bolt into spindle shaft. NOTE: Blade bolt has left hand threads. Tighten blade bolt to 150 ft./lbs. torque. Use heavy leather gloves during tightening process to hold blade and wrench. MAINTENANCE BELT ADJUSTMENT PROCEDURE Shut off mower and tractor. Loosen all four nuts (item 1) on gearbox slide plate (item 2). Loosen jam nut (item 3) on tension adjustment bolt (item 4).
MAINTENANCE BELT REMOVAL/INSTALLATION Shut off mower and tractor. Remove belt shield fasteners and belt shields. Loosen gearbox slide plate bolts and gear box adjustment bolt. Slide gearbox to the full forward position. Slip belts under gearbox sheave (item 8) and over center spindle sheave (item 9). Ensure that right-hand belt (item 7) is in the upper groove of gearbox sheave and that left-hand belt (item 6) is in the lower groove of gearbox sheave.
MAINTENANCE MAINTENANCE STORAGE Your rotary mower represents an investment from which you should get the greatest possible benefit. Therefore, when the season is over, the cutter should be thoroughly checked and prepared for storage so that a minimum amount of work will be required to put it back into operation for the next season. The following are suggested storage procedures: 1. Thoroughly clean the cutter. 2. Lubricate the cutter as covered in Maintenance Section. 3.
MAINTENANCE PROPER TORQUE FOR FASTENERS The chart lists the correct tightening torque for fasteners. When bolts are to be tightened or replaced, refer to this chart to determine the grade of bolts and the proper torque except when specific torque values are assigned in manual text. RECOMMENDED TORQUE IN FOOT POUNDS UNLESS OTHERWISE STATED IN THE MANUAL* TX165A,135A,115A 02/11 © 2011 Alamo Group Inc.
MAINTENANCE BLADE SPINDLE INSTRUCTIONS (Figure Mnt-R-0195) ASSEMBLY PROCEDURE MAINTENANCE 1. 2. 3. Press (Item 6) Cup into both ends of (Item 3) Housing Spindle. Install (Item 5) Bearing into (Item 6) Cup on bottom side of (Item 3) Housing Spindle. Press (Item7) Seal into bottom of (Item3) Housing Spindle. (NOTE: POSITION & DIRECTION OF SEAL FLUSH WITH HOUSING) 4. After Completing Steps 1-3 5. Press Housing/Bearing Assembly. Onto Shaft Assembly. DO NOT USE HYDRAULIC PRESS 6.
RHINO LIMITED WARRANTY 1. 2. LIMITED WARRANTIES 1.01. Rhino warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser (“Purchaser”) and warrants for six months to the original commercial or industrial purchaser (“Purchaser”) that the goods purchased are free from defects in material or workmanship. 1.02.
TO THE OWNER/OPERATOR/DEALER In addition to the standard Limited Warranty shown on the facing page, Rhino also provides: A FIVE-YEAR (60 months) LIMITED WARRANTY* on GEARBOX components provided they have been properly maintained† and have not been subjected to abuse or mis-use except as limited below. * WARRANTY LIMITATIONS - GEARBOX A) Warranty is ONE-YEAR (12 MONTHS) for Seals (After one year, seals are considered to be WEARING PARTS and replacement is the users' responsibility.
TX165A,135A,115A TURF FLEX Rotary Mower TX165A/135A/115A-SOM-02/11 Printed U.S.
