WARRANTY REGISTRATION REGISTER FOR EXTRA BENEFITS Activate within 30 days of purchase: seura.
Compatible with Séura Outdoor TVs: Shade Series: SHD1-55, SHD1-65, SHD1-75, SHD2-43, SHD2-55, SHD2-65, SHD2-75 Ultra Bright: STM3-55-U, STM3-65-U, STM3-86-U Safety Prior to the installation of this product, read all instructions. Keep this manual for future reference. This product is designed to mount televisions and any accessories weighing up to 200 lbs. to a properly rated ceiling structure. CAUTION DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR.
Installation Tools The following tools may be required depending upon your particular Parts and Tools Required (not included) 1/2” The following tools may be required depending on your particular installation. They are not included.
Parts Included P5080T Before using the device, please check the following contents of the box for completeness. Illustrations are Installation Tools not to scale. If any parts are missing orThe damaged, contact following tools may beSéura. required depending upon your particular installation. They are not included.
P5080T Installation Tools Parts Included, Packaged as TW-5 The following tools may be required depending upon your particular installation. They are not inc Electronic Stud Finder ¼˝ Drill Bit for Wood Stud Pencil Level Protective Eyewear Socket Wrench /8 ˝ Concrete Drill Bit* 3 P5080T lation Tools Installation Tools owing tools may be required depending upon your particular installation. They are not included. The following tools may be required depending upon your particular installation.
Features Ceiling Mounting Plate A template with the mounting hole pattern is included to aid installation. Tilt Locking Bolts Allows for tilt angle of the TV adjustment. Top Leveling Screws Allows for leveling adjustments of the TV after mounting. Bottom Locking Screws Prevents the TV from being removed or dislodged from the mounting plate. 6 Directional Mounting Arrows The arrow lets you know which edge is up.
Cable Pass Through Run power and content cables through the back of the pole or into the ceiling. Height Adjustment Use both included screws to set the desired height. Swivel Adjustment Loosening both knobs allows adjustment of the swivel. Always retighten as TV may swivel in the wind. Cable Pass Through Run power and content cables through the pole and connect to the TV inputs.
Step 1: Assemble and Prepare Mount 1. Assemble ceiling mount Ensure the plastic ring is on the Ceiling Bracket Extension. Slide the Mounting Plate Rails onto the Ceiling Bracket Extension. Note: The Mounting Plate Rails is a symmetrical part, so orientation does not matter. 4 5 16 " 1 26 4 1" 17 Platic Ring 15 16 " 44" 2. Attach the Ceiling Bracket Slide the Ceiling Bracket Extension into the Ceiling Bracket.
14" 14" 5 14" 5 5 13 13 16" 16" 5 14" 5 1 2" X 1" 14" 13 16" 5 5 1 2" X 1" 14" 14" 13 16" 13 16" 13 16" 13 5 14" 16" 13 16" 5 13 16" 14" 13 5 13 " 5 16 16" 5 13 16" 14" 13 5 16" 5 13 16" 3. Attach mounting plate to ceiling mount Using the four included fasteners, attach the mounting plate to the ceiling mount rails as shown.
IMPORTANT: HANDLE THE TV IN A VERTICAL POSITION TO AVOID DAMAGE TO THE SCREEN. IF PLACING THE TV SCREEN-SIDE DOWN OR LEANING AGAINST A WALL DURING INSTALLATION, COVER THE SCREEN WITH A PROTECTIVE CLOTH OR BLANKET. Installation IMPORTANT: THIS PRODUCT MUST BE MOUNTED TO A PROPERLY RATED CEILING STRUCTURE. The structure must be able to support five times the weight of the television and the mount combined. A professional installer or structural engineer should inspect or verify the requirements of the wall.
2. Drill pilot holes Wood Joist/Truss Mounting: Pre-drill the four marked holes on the wall 3-inches deep with a 7/32” drill bit. Concrete: Pre-drill the four marked holes on the wall 3-inches deep with a 7/16” masonry drill bit. Insert a plastic anchor into each of these holes. If necessary, lightly tap each anchor into place with a hammer.
3. Attach ceiling mounting plate Align the mounting plate with the pre-drilled holes. Ensure that the cable pass through holes on the mount are positioned appropriately. Wood Joist/Truss Mounting: Align the bracket with the screw keyed slots and turn to hold in place. Finish tightening all lag screws with washers until they are snug with the mounting surface. Do not over tighten the lag screws. Tighten the lag screws only until the washers are pulled firmly against the bracket.
Step 3: Attach Tilt Mount TV Brackets to TV IMPORTANT: Check your TV manual before attaching brackets to TV. Some models require attaching soundbar brackets in tandem with attaching TV brackets. Using a Philips #2 Screwdriver (or 6 mm Allen Wrench for 86” Ultra Bright TV), remove the four VESA mount screws from the back of the TV. Place the two identical Tilt Mount TV Brackets flat against the back of the TV with the arrows pointed towards the top of the TV.
Step 5: Adjust the TV Caution: It is possible to dislodge your TV while you level it. Use extreme caution until you tighten the leveling and locking screws. Top Leveling Screw Séura recommends checking knobs, screws, and bolts every two to six months. Temperature fluctuations, wind, and normal wear and tear can loosen hardware over time. Allows for leveling adjustments of the TV after mounting.
Tilt adjustment: Adjusting the TV Tilt Angle t Angle 1. Place one hand on the center-top edge edge ofof the flat the TV. 2. Place the other hand on the center- bottom edgeof of the TV. r-bottom edge 3. U sing the upper hand, gently pull the top of the TV towards you while the lower he tophand of the gently pushes the bottom of the TV wer hand away gently from you. l away from you. Tilt Locking Bolts Adjusting the TV to the Original Position 1.
Outdoor TV Mount Warranty The standard limited warranty policies of Séura, Inc. (“Séura”) shall apply to all equipment or other goods (“Products”) at the time of sale to any authorized Séura distributor and/or product reseller. These warranty policies may be modified by Séura from time to time. Copies of the standard limited warranties then in effect for a particular Product will be made available upon request and are also available on the Séura website at https://www.seura.com/warranty/.
be reasonably required by Séura to verify the Product’s warranty eligibility. Séura shall have no liability with respect to Products whose serial number has been removed, defaced, replaced, or otherwise tampered with in any manner. Séura reserves the right to examine all failed product components and determine, in its sole discretion, whether any product components are defective and covered under warranty. LIMITATION OF LIABILITY.
Specifications SHORT ARM CEILING MOUNT LONG ARM CEILING MOUNT Model: SC-1 GENERAL DISPLAY COMPATIBILITY 42" - 86" Séura Outdoor TVs CEILING MOUNT DIMENSIONS MOUNTING PLATE DIMENSIONS Collapsed: 26.25” w x 6.6 d x 34” h Extended: 26.25” w x 6.6 d x 42” h Collapsed: 26.25” w x 6.6 d x 48.5” h Extended: 26.25” w x 6.6 d x 70.5” h 6.5" w x 6.5" h 6.5” w x 6.
5" 5 4" 6 2" SHORT ARM CEILING61MOUNT 2" LONG ARM CEILING MOUNT Model: SC-1 Model: LC-1 15 16" FULLY COLLAPSED 22-15/16" FULLY EXTENDED 14 5 4 16" 25mm 1" 7 29 16" FULLY COLLAPSED 51-7/16" FULLY EXTENDED 15 17 16" 5 4 16" 25mm 1" 15 17 16" 19
For technical support, please contact Séura at 1-800-957-3872 during regular business hours: M-F 8:00 am - 4:30 pm, Central Time. 1230 Ontario Road Green Bay, Wisconsin 54311 1-800-957-3872 contacts@seura.com www.seura.com Publish date: September 15, 2020 Information is subject to change without notice.