SHADE SERIES ™ SOUNDBAR INSTALLATION GUIDE SHD2-43 SHD2-55 SHD2-65 SHD2-75
1
x4 Parts Included A: M6 x 35 mm Before installing the soundbar, unpack the box and check for completeness of the following contents. NOTE: Illustrations are not to scale.
Step 1: Prep for Installation a. Lay the TV face down on a soft clean surface. Position the soundbar below the TV, aligning the mounting holes. Take caution not to lay the TV on a surface that will scratch or damage the screen. Position the soundbar on the bottom or top of the TV as desired for installation. b. Using a 3/16 Allen wrench, remove the four screws (part C) from the two mounting brackets (part B) attached to the soundbar (part A) for shipping.
c. (Optional) The Very High Bond (VHB) adhesive strips (part D) provide additional stability between the soundbar and the TV. This bond is permanent and recommended. On both VHB strips, remove the backing from one side and attach the tape to the bottom of the television.
Step 2: Attach the soundbar mounting brackets to the TV a. Lay the soundbar mounting brackets (part B) on the back of the TV so the VESA holes on the TV line up with the holes on the soundbar mounting brackets. The soundbar mounting brackets should hang over the edge of the bottom of the TV. Do not attach yet. Helpful hint: The VESA holes on the TV are the same holes where the screws were removed from the TV in step 1D.
Note: If mounting the soundbar to the top of the TV, the mounting brackets should be reversed so the mounting brackets hang over the edge of the top of the TV. b. Place the TV mounting brackets (sold separately) on top of the soundbar mounting brackets (part B). Reference your TV mount installation instructions to ensure proper placement. c. Use a Phillips #2 screwdriver and the four provided screws (part E) to screw the TV brackets and soundbar mounting brackets tight to the TV.
Step 3: Attach the soundbar to the TV a. Remove the backing on the VHB tape. Do not firmly adhere the soundbar to the TV until completing all of step 3. b. Place the soundbar (part A) underneath the soundbar mounting brackets (part B). The audio cable and power cables coming out of the soundbar should be on the same side of the TV as the media compartment. Adjust the sliding screw receivers in the soundbar mounting channel to line up with the holes on the soundbar mounting brackets.
c. Use the four screws (part C) that you removed in Step 1B and loosely screw the soundbar to the mounting brackets (part B). When installed correctly, the front of the soundbar is flush with the front of the TV. d. Firmly apply pressure to the soundbar against the TV edge to fully engage the VHB tape (part D). e. Use a 3/16 Allen wrench to fully tighten the four screws (part C) to hold the soundbar to the soundbar mounting brackets (part B).
Step 4: Connect the soundbar wires to the AV Compartment on the TV a. Install the snap-in wire saddles (part F) to the soundbar mounting brackets (part B) between the bracket and the TV for a concealed appearance. b. Run the wires from the soundbar through the wire saddles (part F) along the soundbar mounting brackets. Each wire saddle wraps around the wires.
c. Unscrew the thumb screws on the AV compartment on the back of the TV to open it. Plug the 3.5mm audio cable into the Line Out port. Plug the power cable into the power outlet. d. Neatly coil up any excess wires into the AV compartment of the TV. Close the AV compartment lid and tighten the screws.
For technical support, please contact Séura at 1-800-957-3872 during regular business hours: M-F 8:00 am - 4:30 pm, Central Time. 1230 Ontario Road Green Bay, Wisconsin 54311 1-800-957-3872 contacts@seura.com www.seura.com Publish date: June 15, 2020 Information is subject to change without notice.
