ASSEMBLY INSTRUCTIONS UltraHD® Workcenter LED work light included (Model No. 20246) 48 in W X 24 in D X 65.5 in H (1.21 m x 60.9 cm x 1.
PARTS LIST (pg 1 of 9) Please check the parts carefully according to the parts list. If you are missing any parts, please contact our customer service department (please refer to page 9 of 9). Drawer Top Cantilever Shelf Parts No. Qty. Parts No. Qty.
PARTS LIST (pg 2 of 9) Please check the parts carefully according to the parts list. If you are missing any parts, please contact our customer service department (please refer to page 9 of 9). #103 #101 #100 #104 #107 #106 #105 M8X20 pcs #50 #15 #27-B #40 #25 #21 Parts No. #51 #41 Qty. #45 Parts No. Qty. #15 SCREW B (M4 x 8L) 36PCS #100 1/2" CURVED 4PCS #21 SCREW DRIVER 1PC #101 1" CURVED 4PCS #25 WRENCH 1PC #103 1.
ASSEMBLY INSTRUCTIONS (pg 3 of 9) *NOTE: We recommend TWO people to assemble the workbench. TIP: A magnetic screwdriver is included for your convenience. If a power screwdriver is used, keep on a low torque setting. B A Step 1. Install (#5-B) Leg Piece. A: Open the package, and put the parts aside. Then, attach the (#47) "L" Bracket to the (#5-B) Leg Piece, use (#50) Screw I to tighten. Repeat Step A to install (#47) "L" Brackets to another one (#5-B) Leg Piece.
ASSEMBLY INSTRUCTIONS (pg 4 of 9) *NOTE: We recommend TWO people to assemble the workbench. Step 4. Install (#49) Pegboard Long Support Bar. Attach (#49) Pegboard Long Support Bar to the back of the workbench, line up the screw holes, use (#40) Screw E with (#27B) Washer to tighten. NOTE: Do not fully tighten the screws. This will help you make any adjustments to alignment later. Step 5. Install (#3-C) Bottom Pegboard Panel and (#2-C) Top Pegboard Panel.
ASSEMBLY INSTRUCTIONS (pg 5 of 9) *NOTE: We recommend TWO people to assemble the workbench. Step 8. Install (#20-3 & #20-4) Left & Right Drawer Side Panels and (#20-5) Drawer Back Panel. Attach (#20-3 & #20-4) Left & Right Drawer Side Panels and (#20-5) Drawer Back Panel to the (#19-2) Drawer Base Panel. Line up the screw holes and use (#15) Screw B to tighten. #15 #20-3 Back #20-5 #19-2 NOTE: Make sure the hook slots on the (#20-5) Drawer Back Panel are facing inward.
ASSEMBLY INSTRUCTIONS (pg 6 of 9) *NOTE: We recommend TWO people to assemble the workbench. Step 11. Insert Drawer Pull out the drawer sliders to full length, then attach and fit the Drawer to the inner track of the sliders and slide drawers in. NOTE: Make sure to remove the rubber guards on the hooks of the inner track before fitting the drawer in. NOTE: Once you insert the drawers, tighten (#15) Screw B for (#48-2) Small Drawer Left Support and (#483) Small Drawer Right Support. Step 12.
ASSEMBLY INSTRUCTIONS (pg 7 of 9) *NOTE: We recommend TWO people to assemble the workbench. Step 13. Install (#20-7) Drawer Divider Insert Drawer Divider into the drawer. The solid wall of the divider should be facing the desired slot position. Slide the divider towards the slot, then push down into the slots. Repeat the above steps to assemble another Drawer Divider.
ASSEMBLY INSTRUCTIONS (pg 8 of 9) *NOTE: We recommend TWO people to assemble the workbench. Step 16. Place (#100), (#101), (#103), (#104), (#105), (#106), (#107) Hooks to Pegboard as you desire. [!] CAUTION: Potential Shock or Fire Hazard. This unit is not intended for use in wet or potentially wet locations, such as showers, saunas, under or near fishtanks, sinks, etc. Stainless Steel Maintenance: These parts have an UltraGuard™ fingerprint resistant finish.
CONTACT INFORMATION (pg 9 of 9) *If you are missing any parts, have any questions, or need additional assistance in assembly, please contact our bilingual (English/Spanish) customer service department at: Seville Classics, Inc. 19401 South Harborgate Way Torrance, CA 90501 USA Telephone: (800) 323-5565 within USA Hours: 9:00am - 4:30pm (Pacific Standard Time) Fax: (310) 533-3899 E-mail: support@sevilleclassics.com Website & Online Store: www.sevilleclassics.
UltraHD Line Model No. 20184 UltraHD Rolling Drawer Cabinet Model No. 20296 UltraHD Height Adjustable Workbench Model No. 20230 UltraHD Wall Cabinet Model No. 20262 UltraHD Rolling Workbench Model No. 20217 UltraHD Trash Bin Model No.
