MODEL : LK-P11B MOBILE PRINTER All specifications are subject to change without notice
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
1. Product overview Table of Contents 1. Product overview 3 2. Unpacking 4 3. Installation & Usage 5 3-1. Battery Installation 5 3-2. Battery Charging 6 3-3. Battery Charger Usage 7 3-4. Belt Strap Usage 8 3-5. Separation of Battery from the printer 9 3-6. Shoulder Strap Usage 10 3-7. Leather case Usage 11 3-8. Loading the paper 12 3-9. Control Panel Usage 13 3-10. Self Test 14 4. Peripherals Connection 16 4-1. Bluetooth Connection 16 4-2. Interface Cable Connection 17 5.
3. Setting Up the Product 2. Unpacking 3-1. Installing battery Standard Printer Battery Belt Buckle Push the Open to the direction as pointed by arrow in the image. Recharger Roll paper USB Shelded Cable CD Serial Cable Open the battery cover and push up the hook to the direction as above. 1 2 3 Quick Manual Option Insert the battery inside printer as shown. Close the battery cover once you inserted the battery completely.
3-2. Battery Charging 1. The battery can be charged only when the temperature is 0~40℃ 2. Be sure that the printer is turn off and the battery to be charged is installed. 3. Connect the charger to the printer. 4. Recharging will now be started. 3-3. Battery charger Usage 1. Please press the battery into the holder until you can hear a snapping sound . 2. Insert DC JACK ① into the end completely as the direct shown above. 3. Plug the power code to electrical outlet. 4.
3-5. Removing battery 3-4. Belt Hook Usage Insert the belt hook screw into the hole of the belt hook. 1 2 Push the Open into the direction indicated with the arrow in the image. Push up the hook after opening the battery cover. 1 2 3 As shown above, fasten the screw with a screw driver. Pull out the battery as shown above.
3-7. Leather Case Usage 3-6. Shoulder Strap Usage Place the end of strap into the hook of shoulder strap. Insert the strap into the hook on the printer. 1 2 3 4 Open the Velcro 1 2 3 Put the printer into the leather case following the direction shown in the Close the Velcro After pulling out the end of strap tightly, put it into the clip to be fastened. 10 Fasten the strap in the opposite side with the sample way.
3-9. Control Panel 3-8. Loading the media. Button Press the cover open button and open 1 2 3 4 Pull a short length of paper out of the printer and close the cover. 12 Place the paper roll as shown. Make sure the paper is placed in right direction. Name function Power button This button is used to turn the printer on and off. When the printer is off, press this button for approximately 2 seconds and it will turn on the power.
3-10. Self Test < Sample Printout of Self Test > You can check the printer setting state by doing self test when you set the printer first time or encounter some problems. - Control Circuit, Mechanisms, Print Quality, Rom version. When you can not find the exact cause of problem through self test, investigate on other hardware parts or software. This function is independent of other devices and software. ● Self –Test Instructions 1.Turn the printer power off an close the printer paper cover. 2.
4. Peripherals Connection This product can communicate with other devises via Bluetooth communication and cable. 4-2. Interface Cable Connection 4-1.Bluetooth Connection USB Serial 1. The printer can be connected to devices equipped with Bluetooth communication capacity (PDA, PC, etc.) 2. Use the Bluetooth connection function supported by the device to connect to the printer. 1. Connect the interface cable to the cable connector of the printer Notes: Use only cables provided by this manufacturer 2.
5. Printer cleaning If the interior of the printer is dusty, printing quality can lowered. In such a case, follow the instructions below to clean up the printer. NOTE 1. Make sure to turn the printer power off prior to cleaning 2. Regarding print head cleaning, as the print head sets very hot during printing, turn off the printer power and wait approximately 10 minute before commencement. 3. When cleaning the print head, take care not to touch the heated portion of the print head.
SEWOO TECH CO.,LTD. ADDRESS Doosung Bd, 689-20, Kumjung-dong, Kunpo-si, Kyunggi-do, Korea TEL 82-31-459-8200 FAX 82-31-459-8880 URL http://www.miniprinter.com Rev. 1.