MODEL : LK-P21B MOBILE PRINTER All specifications are subject to change without notice
1. Unpacking Table of Contents 1. Product overview 3 2. Unpacking 4 3. Usage and Installation 5 3-1. Control panel usage 5 3-2. Battery Installation 6 3-3. Battery removal 7 3-4. Battery charging 8 3-5. Battery charger usage 9 3-6. Usage of Cigar Jack for charging 10 3-7. Belt clip usage 12 3-8. Roll paper installation 13 3-9. Leather case usage 14 3-10. Self test 15 3-11. MSR usage 16 4. Peripherals connection 17 4-1. Bluetooth connectiontion 17 4-2.
2. Product overview 3. Usage and Installation 3-1 Control panel usage Paper feed button Open Button Power switch USB Button Name function SERIAL Power button Belt clip hole Battery Paper Feed Button Battery Status Lamp DC Power 4 Error Lamp This button is used to turn the printer on and off. When the printer is off, press this button for approximately 2 seconds and it will turn on the power. When you press this button in a state that the printer is on, the printer will turn off.
3-2 Battery Installation 3-3 Battery removal 180˚ Hook Put up the Belt clip hole turning 180 degree. 1. Align battery hook as shown in the picture 2. Push the battery into the printer until it locks in place. 1 2 NOTE As the battery is not charged at the time of your purchase, charge the battery prior to using the printer (Battery charger or Cradle can be used to charge) After putting up the belt clip, remove the battery holding it up as shown above.
3-4 Battery charging 3-5 Battery charger usage lamp 1. Be sure that the printer is turned off 2. After open the DC JACK cover, insert DC JACK into the printer. 3. Plug the power code to electrical outlet. NOTE 1. Unless the exclusive charger is used provided by the manufacturer, the printer can be damaged, and the manufacturer is not liable for the consequential damage. 2. Before removing the battery, make sure that power is turned off. 3.
3-6 Usage of Cigar Jack for charging 3-7 Belt Clip usage Printer Insert the belt clip screw into the hole of Belt clip 1 2 Battery holder Connect the car cigar JACK charger into the printer or battery holder. 10 As shown in the picture, tighten the screw with a screw driver.
3-8 Roll Paper installation 3-9 Leather case usage Press the PUSH button to open paper cover Insert the paper in the right direction Open the leather case 1 2 3 4 Pull a short length of paper out of the printer and close the cover. 12 Place the printer into the leather case 1 2 3 4 Tear off the additional paper using tear bar. Close the Velcro and stick the cover.
3-10 Self Test Turn off the power pressing the power button for approximately 2 minutes. While you are pressing the FEED button, press the power button 1 2 3 NOTE 1. To print ASCII pattern additionally, press the Feed button once more 2. After printing ASCII pattern, the self test will be finished automatically. 3. If the Feed button is not pressed to print ASCII pattern, self test will be finished automatically after 30 seconds.
4. Peripherals connection 3-11 MSR usage This printer can communicate with Peripherals device via Bluetooth and cables. 4-1 Bluetooth Connection Insert and swipe the card in the direction of the arrow as shown in the picture. 1. Printer can be connected to the PDA and PC which can do wireless communication. 2. By using Bluetooth function supported in PC, printer can be connected.
5. Pritner Specification 4-1 Bluetooth Connection 5-1 Specification USB Serial 1. Connect USB or Serial cable into the cable connector on the printer.
Battery Charger Battery Charger Size input AC100~240V, 50/60 Hz output 8.4V , 800~1200mA Battery type Li-on output 7.4V, 1130mAh Charging time 2 Time W X D X H(mm) 96 X 136 X 58 W X D X H” 3.7 X 5.3 X 2.2 0.
5GVVKPI WR VJG UQHVYCTG 3OHDVH UHIHU WR WKH SURJUDPPLQJ PDQXDO LQFOXGHG LQ &' ǁ%GTVKHKECVKQP (%% +PHQTOCVKQP This device complies with part 15 of the FCC Results. Operation is subject to the following two conditions: (1) This Device may not cause harmful interface, and (2) This device must accept any interference received, including interference that may cause undesired operation. %#76+10 #PVGPPC UJCNN DG OQWPVGF KP UWEJ C OCPPGT VQ OKPKOK\G VJG RQVGPVKCN HQT JWOCP EQPVCEV FWTKPI PQTOCN QRGTCV
SEWOO TECH CO.,LTD. ADDRESS Doosung Bd, 689-20, Kumjung-dong, Kunpo-si, Kyunggi-do, Korea TEL 82-31-459-8200 FAX 82-31-459-8880 URL http://www.miniprinter.com Rev. 1.
