MODEL : LK-P30B MOBILE PRINTER All specifications are subject to change without notice
1. Unpacking Table of Contents 1. Product overview 3 2. Unpacking 4 3. Usage and Installation 5 3-1. Control panel usage 5 3-2. Battery Installation 6 3-3. Battery removal 7 3-4. Battery charging 8 3-5. Battery charger usage 9 3-6. Belt clip usage 10 3-7. Roll paper installation 11 3-8. Leather case usage 12 3-9. Self test 13 3-10. MSR usage 15 3-11. IC CARD usage 16 4. Peripherals connection 17 4-1. Bluetooth connectiontion 17 4-2. Interface cable connection 18 5.
2. Product overview 3. Usage and Installation 3-1 Control panel usage Power switch Control Panel Open Button Paper feed button Button Name DC Power Battery Belt clip hole SERIAL function Power button This button is used to turn the printer on and off. When the printer is off, press this button for approximately 3 seconds and it will turn on the power. When you press this button in a state that the printer is on, the printer will turn off.
3-2 Battery Installation 3-3 Battery removal 180˚ Hook 1. Align battery hook as shown in the picture 2. Push the battery into the printer until it locks in place. Put up the Belt clip hole turning 180 degree. 1 2 NOTE As the battery is not charged at the time of your purchase, charge the battery prior to using the printer (Battery charger or Cradle can be used to charge) ☞CAUTION Risk of explosion if battery is replaced by an incorrect type.
3-4 Battery charging 3-5 Battery charger usage Optional lamp DC Jack 1. Be sure that the printer is turned off 2. After open the DC JACK cover, insert DC JACK into the printer. 3. Plug the power code to electrical outlet. NOTE 1. Unless the exclusive charger is used provided by the manufacturer, the printer can be damaged, and the manufacturer is not liable for the consequential damage. 2. Before removing the battery, make sure that power is turned off. 3.
3-6 Belt Clip usage 3-7 Roll Paper installation Insert the belt clip screw into the hole of Belt clip 1 2 As shown in the picture, tighten the screw with a screw driver. 10 Press the PUSH button to open the paper cover Insert the paper in the right direction 1 2 3 4 Pull a short length of paper out of the printer and close the cover. Tear off the additional paper using tear bar.
3-8 Leather case usage 3-9 Self Test Optional Open the leather case Place the printer into the leather case 1 2 3 4 Turn off the power pressing the power button for approximately 3 seconds. While you are pressing the FEED button, press the power button 1 2 3 NOTE 1. To print ASCII pattern additionally, press the Feed button once more 2. After printing ASCII pattern, the self test will be finished automatically. 3.
When the printer is installed initially or when you face a problem, you can run the 3-10 MSR usage Optional Insert and swipe the card in the direction of the arrow as shown in the picture. self test and check the information about -Control Circuit, Mechanism, Print Quality, ROM Version After checking with self-test and no issues are found, you can examine other devices and software. This function is working independent of devices and software.
4. Peripherals connection 3-11 IC CARD usage Optional This printer can communicate with Peripherals device via Bluetooth and cables. 4-1 Bluetooth Connection Insert the card in the direction of the arrow as shown in the picture. 1. Printer can be connected to the PDA and PC which can do wireless communication. 2. By using Bluetooth function supported in PC, printer can be connected.
5. Pritner Specification 4-2 Interface Cable Connection 5-1 Specification Printing Method Direct Thermal Printing Speed 100mm/sec Resolution 203 DPI X 203 DPI Character Font A (12X24), Font B (9X17) Character per line Font A : 48pt , Font B : 64pt Character set ALPHA NUMERIC Character, Extension Character Barcode EAN-8, EAN-13, Code39, ITF, UPC-A,UPC-E, Codabar, Code93, Code128, PDF417(2D), MAXICode (2D) Emulation ESC/POS, CPCL, Commanl Compatible Driver Window CE 4.2&5.0, Window Mobile 5.
6. CPCL Command Compatibility EMVTM level one certified smart card reader IC CARD (Optional) Battery Charger Battery Charger Size output 8.4V , 800~1200mA Battery type Li-ion output 7.4V, 2200mAh Charging time 2-and-a-half hour Printer Commands W X D X H(mm) 120 X 152 X 70 PRINT ○ FORM ○ JOURNAL ○ UNITS ○ 4.7 X 5.9 X 2.7 0.
Graphics ○ LINE ○ INVERSE-LINE ○ PATTERN ○ GRAPHICS ○ PCX ○ Advanced Commands Compatibility CONTRAST ○ TONE ○ JUSTIFICATION ○ PAGE-WIDTH ○ PACE ○ NO-PACE ○ WAIT ○ REWIND TENSION SETSP ○ ○ PREFEED ○ POSTFEED ○ ○ Moving With X and Y Coordinates ○ LMARGIN ○ SETBOLD ○ SETSP ○ Special ASCII Characters ○ SETFF ○ SET-TOF ○ SETLP-TIMEOUT ○ X COUNTRY/CODE PAGE ○ FORMAT FILES ○ BEEP ○ CUT X MCR ○ SETLF X ON-FEED PATIAL-CUT Compatibility SETLP X ○ PR
7. Setting up the software Please refer to the programming manual included in CD. ♣Certification FCC Information This device complies with part 15 of the FCC Results. Operation is subject to the following two conditions: (1) This Device may not cause harmful interface, and (2) This device must accept any interference received, including interference that may cause undesired operation. CAUTION Antenna shall be mounted in such a manner to minimize the potential for human contact during normal operation.
SEWOO TECH CO.,LTD. ADDRESS Doosung Bd, 689-20, Kumjung-dong, Kunpo-si, Kyunggi-do, Korea TEL 82-31-459-8200 FAX 82-31-459-8880 URL http://www.miniprinter.com Rev. 1.
