SEWOO TECH CO.,LTD. Doosung BD, 689-20, Geumjung-dong, Gunpo-si, Gyeonggi-do, 435-862 South Korea TEL : +82-31-459-8200 FAX : +82-31-459-8880 www.miniprinter.com MODEL : LK-P31 MOBILE PRINTER Rev. 1.
Table of Contents 1. Unpacking 2 2. Product overview 3 3. Usage and Installation 4 3-1. Control panel usage 4 3-2. Battery Installation 5 3-3. Battery removal 6 3-4. Battery charging 7 3-5. Battery charger usage 8 3-7. Roll paper installation 9 38. Self test 10 4. Peripherals connection 12 4-1. Bluetooth connectiontion 12 4-2. Interface cable connection 13 5. Printer specification 5-1. Specification 6.
2. Product overview 1.
3. Usage and Installation 3-1 Control panel usage 3-2 Battery Installation Hook Button Name Power button This button is used to turn the printer on and off. When the printer is off, press this button for approximately 3 seconds and it will turn on the power. When you press this button in a state that the printer is on, the printer will turn off. Paper Feed Button Paper output can be done manually by pressing this button. Additionally, self-testing and Hexadecimal Dumping can be processed.. 1.
3-3 Battery removal 3-4 Battery charging Lamp After putting up the belt clip, remove the battery holding it up as shown above. 1. Be sure that the printer is turned off 2. After open the DC JACK cover, insert DC JACK into the printer. 3. Plug the power code to electrical outlet. 3-4-1 The status of lamp in charging Status charging charging complete Charging Lamp Red Green NOTE 1.
3-5 Battery charger usage 3-6 Roll paper installation Optional Lamp DC Jack 1. Insert the battery into the battery holder as shown above 2. Connect the DC JACK to the power electrical outlet. Press the PUSH button to open the paper cover Insert the paper in the right direction 1 2 3 4 3. Plug the power code into the electrical outlet. 4. Once the charging is completed, remove the battery from the holder.
3-7 Self Test The sample of self test printout Turn off the power pressing the power button for approximately 3 seconds. While you are pressing the FEED button, press the power button 1 2 3 NOTE 1. To print ASCII pattern additionally, press the Feed button once more 2. After printing ASCII pattern, the self test will be finished automatically. 3. If the Feed button is not pressed to print ASCII pattern, self test will be finished automatically after 30 seconds.
4. Peripherals connection This printer can communicate with Peripherals device via Bluetooth and cables. 4-2 Interface Cable Connection 4-1 Bluetooth Connection USB 1. Printer can be connected to the PDA and PC which can do wireless communication. 2. By using Bluetooth function supported in PC, printer can be connected. NOTE Refer to the Bluetooth Manual for more details on connection. 12 1. Connect USB into the cable connector on the printer. NOTE Use the cable offered by the manufacturer (USB) 2.
5. Pritner Specification 5-1 Specification Size Printing Method Direct Thermal Printing Speed 60mm/sec Resolution 203 DPI X 203 DPI Character Font A (12X24), Font B (9X17) Character per line Font A : 48pt , Font B : 64pt Character set ALPHA NUMERIC Character, Extension Character Barcode EAN-8, EAN-13, Code39, ITF, UPC-A, Codabar, Code93, Code128 110 X 105 X 30 W X D X H” 4.3 X 4.1 X 1.
6. Certification FCC Information This device complies with part 15 of the FCC Results. Operation is subject to the following two conditions: (1) This Device may not cause harmful interface, and (2) This device must accept any interference received, including interference that may cause undesired operation. This Class [B] digital apparatus complies with Canadian ICES-003. Cet appareil numerique de la classe [B] est conforme a la norme NMB-003 du Canada.
