MODEL : LK-P41W MOBILE PRINTER All specifications are subject to change without notice
1. Unpacking Table of Contents Standard 1. Product overview 3 2. Unpacking 4 3. Usage and Installation 5 3-1. Control panel usage 5 3-2. Battery Installation 6 3-3. Battery charging 7 3-4. Battery charger usage 8 3-5. Roll paper installation 9 3-6. Leather case usage 10 3-7. Self test 11 4. Peripherals connection 13 4-2. Interface cable connection 14 5-1. Specification Charger CD 15 15 6. CPCL Command Compatibility 17 USB Cable Shielded Roll paper Serial Cable 7.
2. Product overview 3. Usage and Installation 3-1 Control panel usage Open Button Paper feed button Power switch USB SERIAL Battery DC Power Button Name Power button This button is used to turn the printer on and off. When the printer is off, press this button for approximately 3 seconds and it will turn on the power. When you press this button in a state that the printer is on, the printer will turn off. Paper Feed Button Paper output can be done manually by pressing this button.
3-2 Battery Installation 3-3 Battery charging Hook 1. Align battery hook as shown in the picture 2. Push the battery into the printer until it locks in place. NOTE As the battery is not charged at the time of your purchase, charge the battery prior to using the printer (Battery charger or Cradle can be used to charge) ☞CAUTION Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions 6 1. Be sure that the printer is turned off 2.
3-5 Roll Paper installation 3-4 Battery charger usage Optional DC Jack lamp 1. Insert the battery into the battery holder as shown above 2. Connect the DC JACK to the power electrical outlet. 3. Plug the power code into the electrical outlet. 4. Once the charging is completed, remove the battery from the holder.
3-6 Leather case usage 3-7 Self Test Optional Open the leather case Place the printer into the leather case 1 2 3 Turn off the power pressing the power button for approximately 3 seconds. While you are pressing the FEED button, press the power button 1 2 3 NOTE 1. To print ASCII pattern additionally, press the Feed button once more 2. After printing ASCII pattern, the self test will be finished automatically. 3.
4. Peripherals connection This product can communicate with other devices via Wifi(802.11b/g) communication and cable. 4-1 Wifi(802.11b/g) Connection 1. The Printer can be connected to devices equipped with wifi(802.11b/g) communication capacity (PDAs, PCs, etc.) 2. Use the wifi(802.11b/g) connection function supported by the device to connect to the printer.
5.
6. CPCL Command Compatibility NOTE Battery Charger Size Battery type Li-ion output 7.4V, 2200mAh Charging time 3 hour 40 minute W X D X H(mm) 149 X 161 X 69 W X D X H” 5.8 X 6.3 X 2.7 0.53kg (With Battery) Weight Temperature Humidity operation -10 ~ 50℃ storage -20 ~ 60℃ operation 35 ~ 95% Compatible with only Partially Compatible commanders provided Compatible by the manufacturer.
Graphics ○ Line Print Mode LINE ○ SETLP ○ INVERSE-LINE ○ SETLF ○ PATTERN ○ Moving With X and Y Coordinates ○ GRAPHICS ○ LMARGIN ○ PCX ○ SETBOLD ○ SETSP ○ CONTRAST ○ Special ASCII Characters ○ TONE ○ SETFF ○ JUSTIFICATION ○ SET-TOF ○ PAGE-WIDTH ○ SETLP-TIMEOUT ○ PACE ○ NO-PACE ○ WAIT ○ Advanced Commands REWIND TENSION Compatibility X ○ SETSP ○ X ON-FEED ○ PREFEED ○ POSTFEED ○ PRESENT-AT X COUNTRY/CODE PAGE ○ FORMAT FILES ○ BEEP ○ CUT X PATI
7. Setting up the software Please refer to the programming manual included in CD. ♣Certification FCC Information This device complies with part 15 of the FCC Results. Operation is subject to the following two conditions: (1) This Device may not cause harmful interface, and (2) This device must accept any interference received, including interference that may cause undesired operation.
SEWOO TECH CO.,LTD. ADDRESS Doosung Bd, 689-20, Kumjung-dong, Kunpo-si, Kyunggi-do, Korea TEL 82-31-459-8200 FAX 82-31-459-8880 URL http://www.miniprinter.com Rev. 1.
