SGW101X BLE Modules Series Model：SGW1010，SGW1010A，SGW1011，SGW1011A
SGW101X Series 1. Introduction The SGW101X series is an advanced, highly flexible, ultra-low power multiprotocol SoM that enable Bluetooth (BLE) connectivity for portable, extremely low power embedded systems. The SGW101X series delivers robust RF performance, low energy consumption, a wide selection of MCU peripherals and either an integrated PCB trace antenna or a u.FL connector for an external antenna.
SGW101X Series o System On mode, with full RAM retention: 2.35uA o System Off mode, with full RAM retention: 1.86uA o Operating Temperature: −40°C to 85°C o CE Pending o BQB: Pending o FCC: 2AS9401 o IC: 25021-01 o Mechanical Dimension: 10.2mm x 15.0mm x 2.1mm APPLICATIONS o Connected home o Smart city infrastructure o Industrial mesh networks o Industrial smart lighting o Logistics and transportation @2019 | SG Wireless Limited Confidential Proprietary 2 Website : www.sgwireless.
SGW101X Series 目录 1. Introduction................................................................................................................................................1 2. Features......................................................................................................................................................1 3. Ordering Information..................................................................................................................................4 4.
SGW101X Series 3. Ordering Information Part No Description SGW1010 Bluetooth 5 module, Built-in antenna SGW1011 Bluetooth 5 module, u.FL connector for external antenna SGW1010A Bluetooth 5 module, Built-in antenna, Low voltage operation SGW1011A Bluetooth 5 module, u.FL connector for external antenna, Low voltage operation SGW1010–EVK SGW1010 Bluetooth 5 module Evaluation Kit @2019 | SG Wireless Limited Confidential Proprietary 4 Website : www.sgwireless.
SGW101X Series 4. Electrical Specifications A. Absolute Maximum Ratings Symbol Min. Max. Unit Voltage on VCC supply pin -0.3 3.9 V VCCHmax Voltage on VCCH supply pin -0.3 5.8 V VBUSmax Voltage on VBUS supply pin -0.3 5.8 V VIOmax Voltage on GPIO pin (VCC > 3.6V) -0.3 3.9 V VIOmax Voltage on GPIO pin (VCC ≤ 3.6V) -0.3 VCC+0.3V V Tstorage Storage Temperature Range -40 125 ℃ VCCmax Parameter Table 3 Absolute Maximum Ratings B. Operating Conditions Symbol Parameter Min.
SGW101X Series 5. Module Interface A. Power Management i. Module supply input (VCC & VCCH) The SGW101X series use integrated two step-down regulators (REG0 & REG1) to transform the supply voltage presented at the VCC & VCCH pins into a stable system voltage. Each regulator can be programmed as Low-dropout regulator (LDO) or Buck regulator (DC/DC), depends on the operating mode of the module.
SGW101X Series B. RF antenna interface i. 2.4 GHz radio The SGW101X series BLE module have their own 2.4 GHz antenna solutions respectively: o The SGW1010/SGW1010A modules use a PCB trace antenna integrated into the module’s PCB. This low-profile antenna solution is useful in space constrained designs. o The SGW1011/SGW1011A modules provide an onboard antenna connector with a nominal characteristic impedance of 50 Ω. ii.
SGW101X Series RPD Pull-down Resistance 11 13 16 kΩ i. Serial interfaces The SGW101X series provide the following serial communication interfaces: o 2x UART interfaces: 4-wire universal asynchronous receiver/transmitter interface used for AT command interface, data communication, and u- connect software upgrades using the Software update +UFWUPD AT command. o 3x SPI interfaces: Up to three serial peripheral interfaces can be used simultaneously.
SGW101X Series trace data allows a user to record exactly how the application goes through the CPU instructions in real time. The parallel trace interface uses 1 clock signal and 4 data signals respectively – TRACE_CLK, TRACE_D0, TRACE_D1, TRACE_D2 and TRACE_D3. 6. Mechanical Dimension Figure 7 SGW1010/SGW1010A (Embedded Antenna) Mechanical Information Figure 8 SGW1011/SGW1011A (External Antenna) Mechanical Information @2019 | SG Wireless Limited Confidential Proprietary 9 Website : www.sgwireless.
SGW101X Series 7. Module Marking Figure 10 SGW1010/SGW1010A/SGW1011/SGW1011A Module label @2019 | SG Wireless Limited Confidential Proprietary 10 Website : www.sgwireless.
SGW101X Series 8. Soldering Temperature-Time Profile for Re-Flow Soldering Figure 11 Soldering Temperature-Time Profile for Re-Flow Soldering Remark: SGW101X series are rated as MSL 3, 168-hour floor life after opening. @2019 | SG Wireless Limited Confidential Proprietary 11 Website : www.sgwireless.
SGW101X Series 9. Certifications A. Qualified Antenna Type The SGW1011 and SGW1011A module supporting an external antenna have been designed to operate with a standard 3 dBi dipole antenna. Any antenna of a different type or with a gain higher than 3 dBi is strictly prohibited for use with this device. Using an antenna of a different type or gain more than 3 dBi will require additional testing for FCC, CE and IC. The required antenna impedance is 50 Ω. B. Manufacturer Part Number Max.
SGW101X Series C. FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. installation. These limits are designed to provide reasonable protection against harmful interference in a residential This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
SGW101X Series may not cause harmful interferences, and (2) this device must accept any interference received, including interference that may cause undesired operation.” The user’s manual for the host product must clearly indicate the operating requirements and conditions that must be observed to ensure compliance with current FCC RF exposure guidelines.
SGW101X Series Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
SGW101X Series 10. Product Packaging Carrier Tape dimension for SGW1010/SGW1010A/SGW1011/SGW1011A. Figure 12 SGW1010/SGW1010A/SGW1011/SGW1011A Tape Dimensions Reel Packaging: 1000 modules will be loaded into the REEL. Each reel will be placed in an antistatic bag and put into a 340 x350x45mm box as shown in below diagram. @2019 | SG Wireless Limited Confidential Proprietary 16 Website : www.sgwireless.
SGW101X Series Figure 13 SGW1010/SGW1010A/SGW1011/SGW1011A Reel Packaging Packaging Label Figure 14 SGW1010/SGW1011 Packaging Label 11. Revision History Revision 0.1 Date Description May 31, 2019 Initial Release 12. Useful Link o Nordic Infocenter: o https://infocenter.nordicsemi.com/index.jsp o o All the necessary technical files and software development kits of Nordic’s chip are on this website. Nordic Developer Zone: o https://devzone.nordicsemi.
