SGW6008 BLE WiFi Gateway User Manual Version 1.
SGW6008 BLE Gateway User Manual 1. Introduction The SGW6008 is a Bluetooth Low Energy ® (BLE) to Wi-Fi connectivity gateway without using smartphones or apps. This robust gateway collects data from BLE sensors or devices, and sends to the local server or remote cloud server by HTTPS & MQTTS protocols with TLS1.2 standard over Wi-Fi.
SGW6008 BLE Gateway User Manual 4. Block Diagram Below (Fig.1) is the block diagram of the SGW6008 BLE WiFi Gateway. Figure 1. SGW6008 BLE WiFi Gateway Block Diagram 5. SGW6008 BLE WiFi Gateway User interface and connector available on the SGW6008 BLE WiFi Gateway are shown below (Figure 2) Figure 2. SGW6008 BLE WiFi Gateway Connector/Button Description USB Micro-USB, power input (5.
SGW6008 BLE Gateway User Manual Top LEDs present on the SGW6008 BLE WiFi Gateway indicates the following status: Power LED Bluetooth LED WFi LED Power-on On - - Bluetooth Signal transmission On Blinking - WiFi Signal transmission On - Blinking AP mode, Not connected Blinking - Blinking AP mode, connected Blinking - On On - Blinking Normal Operation AP Mode Operation WiFi configuration success and connected to SG Wireless IoT server Figure 3.
SGW6008 BLE Gateway User Manual 6. Electrical Specifications Absolute Maximum Rating Power supply 5.5V DC Storage temperature -20°C to 80°C Recommended Operating Conditions Power supply 5.0V DC Operating temperature -10°C to 60°C BLE RF Performance Radio Operating Frequencies 2402MHz ~ 2480MHz Radio On-Air Data Rate 1Mbps, 2Mbps Maximum Transmit Power 10+/-2dBm Antenna Onboard PCB Antenna Range Up to 200 meters (open space) WiFi Performance Wireless Standard IEEE 802.
SGW6008 BLE Gateway User Manual 7. Getting Started 7.1 Wi-Fi Configuration and Provisioning of SGW6008 Wi-Fi configuration and gateway provisioning process must be finished first in order to use the functionalities of the SGW6008. 1. Power-up the SGW6008 BLE WiFi Gateway with micro-USB cable. 2. Connect the gateway with your computer or mobile device. a. SSID of the SGW6008 BLE WiFi Gateway: “SGW6008_AA:BB:CC:DD:EE:FF” b. Default password of the SGW6008 BLE WiFi Gateway: “SGWireless_23$” 3.
SGW6008 BLE Gateway User Manual Wi-Fi configuration procedures: 4. Press “Scan” button in main page to scan for available Wi-Fi Access points in the area. 5. Enter the password for target Wi-Fi access point and press “+” in Action. 6.
SGW6008 BLE Gateway User Manual 7. If static IP is preferred, select “No” for DHCP and enter the IP address, Subnet Mask and DNS of the WiFi access point in the WI-FI configuration table. Press “Save Wifi Setting” button to update the setting. * The “High Priority Slot” represents which saved SSID is the highest priority to connect with. Gateway provisioning procedures: 8. Fill in the SGW IoT Platform account and gateway information, then select “Start Provisioning”. 9.
SGW6008 BLE Gateway User Manual 10. Upon confirmation, the gateway will exit AP mode and start the provisioning with SGW IoT Backend server. During the process, the configuration web page will be directed to SG IoT Website. Please make sure your PC or mobile device has switched to networks with proper internet connection. 7.2 Edge Devices Provisioning The SGW8130 BLE Sensor Tag can be connected to the SGW6008 BLE WiFi Gateway. Provisioning procedures for edge devices SGW8130: 1.
SGW6008 BLE Gateway User Manual 2. Search and Connect Edge Device a. Click ‘SEACH NEW BLE’ to search for nearby edge devices SGW8130. b. Click the Green Discovered BLE device icon which is showing the Mac Address of your target edge device c. Fill in the information of the edge device (name, location, description) d. Click “SUBMIT” to provision the edge device e.
SGW6008 BLE Gateway User Manual 8. Getting Started 8.1 CE Statement Regulatory Conformance (RED) Hereby, (SG Wireless Limited) declares that the radio equipment type (SGW6008) is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following website: https://www.sgwireless.com 8.2 FCC Statement This device complies with part 15 of the FCC rules.
SGW6008 BLE Gateway User Manual • This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. 8.3 IC Statement This device complies with RSS-247 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
SGW6008 BLE Gateway User Manual Contact us: Home Page: www.sgwireless.com LinkedIn: https://www.linkedin.com/company/ sgwireless/ Twitter: @sgwirelessIoT Information in this document is provided solely to enable authorized users or licensees of SG Wireless products. Do not make printed or electronic copies of this document, or parts of it, without written authority from SG Wireless. SG Wireless reserves the right to make changes to the products and information herein without further notice.
