Data Sheet
Table Of Contents
- Abstract
- 1. Introduction
- 2. Characteristics
- 3. Pin Definition
- 4. System memory Space
- 5. ATE（RF Test Mode）
- 5.1. Wi-Fi ATE Command
- 5.1.1. Start MP mode
- 5.1.2. Stop MP mode
- 5.1.3. Set Tx rate
- 5.1.4. Set operational channel
- 5.1.5. Set operational bandwidth
- 5.1.6. Set Tx power
- 5.1.7. Set antenna for Tx
- 5.1.8. Set antenna for Rx
- 5.1.9. Start air Rx mode
- 5.1.10. Start continuous Tx mode
- 5.1.11. Query air Rx statistics
- 5.1.12. Reset air Tx/Rx statistics
- 5.2. Bluetooth ATE Command（TBD）
- 5.3. Example Command
- 5.1. Wi-Fi ATE Command
- 6. Flash Programming
- 7. Electrical Parameters
- 8. RF Parameter
- 9. Antenna Information
- 10. Dimensions and Production Guidance
- 11. Production Guidelines
- 12. FCC and IC Information
- 12.1. FCC Warning
- 12.2. IC warning
- 12.3. Trace antenna designs
- 12.4. RF exposure considerations
- 12.5. Antennas
- 12.6. Label and compliance information
- 12.7. Information on test modes and additional testing requirements5
- 12.8. Additional testing, Part 15 Subpart B disclaimer
- 12.9. The module is limited to OEM installation ONLY.
- 12.10. The OEM integrator is responsible for ensuring that the end-user has no manual instructions to remove or install module.
- 12.11. The module is limited to installation in mobile or fixed applications
- 13. Packaging and Label Information
- 14. Sales and Technical Support Information
EMC3380 Series Wireless Module Data Manual
Copyright of Shanghai MXCHIP Information Technology Co., Ltd.
25
5.1.10. Start continuous Tx mode
This command is used for continuous packet testing. Use the time command to set the sending time. Use
the count command to set the number of sending packets. If neither time nor count is set, the continuous
packet sending mode is started. If the background mode is not set, any character input can stop sending
packets. If the cs mode is set, transmitting through the carrier suppression signal. Use the stone command to
send a single tone signal for testing the frequency. If stone is set, the sending signal will not be a recognizable
message. By default, sending the short duty cycle signal with hardware. If pkt is set, data packet is controlled
by software.
iwpriv mp_ctx count=n,background,stop,pkt,cs,
iwpriv mp_ctx count=n,background,stop,pkt,cs,stone
t: set the sending packet time
n: set the sending packet quantity
background: set the background sending packet mode
stop: Stop the background sending packet
pkt: send tx message
cs: send carrier suppressions signal
stone: send Single Tone signal
5.1.11. Query air Rx statistics
Used for wireless message counting. When transmitting data packets, use this command to get the number
of packets that have been transmitted. When received, this command can be used to get
iwpriv mp_query
5.1.12. Reset air Tx/Rx statistics
This command can count the number of recharge messages. When sending, this command can reset the
number of packets sent, and when receiving, it can reset the number of packets with correct and CRC errors.
iwpriv mp_reset_stats
Bluetooth ATE Command（TBD）
Example Command
continuous sending test
iwpriv mp_start //enter MP mode
iwpriv mp_channel 1 //set channel to 1 . 2, 3, 4~11 etc.
iwpriv mp_bandwidth 40M=0,shortGI=0 //set 20M mode and long GI
iwpriv mp_ant_tx a //select antenna A for operation