Smart Module SIMT 1502 ________________________________________________________________ Hardware Version: V1.2 Software Version:CB03_8909_V4.4_20160901 Manufacturer SHANGHAI SIMCOM LIMITED Building A,SIM Technology Building,No.
SHANGHAI SIMCOM LIMITED This device is restricted to indoor operation only in the band 5150 - 5350 MHz. (Only for devices that support 802.11 5 GHz functions) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
SHANGHAI SIMCOM LIMITED (1)the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; (2)the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit; and (3)the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall comply with the e.i.r.p.
SHANGHAI SIMCOM LIMITED Contents _____________________________________________________________________________ 1 Introduction ....................................................................................................................................................................... 6 1.1 Documentation overview ..................................................................................................................................... 6 1.2 Key features ...................................
SHANGHAI SIMCOM LIMITED 4.13 Other interface.................................................................................................................................................. 29 4.13.1 Camera flash Signal .............................................................................................................................. 29 4.13.2 PM_VIB_DRV_N Signal....................................................................................................................... 29 4.13.
SHANGHAI SIMCOM LIMITED 1 Introduction 1.1 Documentation overview This document describes electrical specifications, RF specifications, function interface, mechanical information and testing conclusions of the SIMT1502. With the help of this document, the users can easily and quickly use SIMT1502 on their own applications. 1.2 Key features 1.2.1 Feature introduction SIMT1502 is a very powerful baseband module with 124 pins interface.
SHANGHAI SIMCOM LIMITED Video applications performance Graphics Audio Codec ■ Low-power audio ■ Voice codec support ■ Audio codec support ■ Enhanced audio ■ Synthesizer Audio inputs Audio outputs Connectivity BLSP ports ■ UART ■ I2C ■ SPI (master only) USB interface Secure digital interfaces Wireless connectivity ■ WLAN ■ Bluetooth Touch screen support Temperature Operating Temperature Storage Temperature ■Encode: H.264 BP/MP – HD(720p),30 fps MPEG-4 SP/H.
SHANGHAI SIMCOM LIMITED 1.
SHANGHAI SIMCOM LIMITED 1.
SHANGHAI SIMCOM LIMITED Table1-2 Terms and acronyms (cont.) Term HSUPA I2C I2S ISP JTAG kbps LCD LPA LPASS LPDDR LSB LTE MBP MDM MIPI MPM MSB MTP NSP PA PCM PI PDM PM PNSP PO PVS RBDS RDS RLP RPM SBI SD SDC SEE SFS SIM SMT SPI Definition High-speed uplink packet access Inter-integrated circuit Inter-IC sound Image signal processing Joint Test Action Group (ANSI/ICEEE Std. 1149.
SHANGHAI SIMCOM LIMITED Table1-2 Terms and acronyms (cont.
SHANGHAI SIMCOM LIMITED 2 Interface Definitions _______________________________________________________________________________ 2.
SHANGHAI SIMCOM LIMITED 2.
SHANGHAI SIMCOM LIMITED SE955_TRIGGER /N5600_ILL * P3 DO; B-PD:nppukp - AI 29 UART2_CTS_N/SCL 30 NC 31 WIFI_BT_RF 32 GND 33 TS_IN_N TS_IN_N 34 TS_I2C_SDA TS_I2C_SDA GPIO_18 P3 35 TS_I2C_SCL TS_I2C_SCL GPIO_19 P3 36 TS_RST_N TS_RST_N GPIO_12 * P3 37 SD_CARD_DET_N MIPI_SW_EN GPIO_38 * P3 38 UART2_TX UART2_TX GPIO_20 * P3 39 UART2_RX UART2_RX GPIO_21 * P3 40 KYPD_SNS0 KYPD_SNS0 GPIO_90 * P3 41 KYPD_SNS1 KYPD_SNS1 GPIO_91 * P3 42 KYPD_SNS2 / KYPD
SHANGHAI SIMCOM LIMITED 62 GND 63 GPIO_29 CAM_I2C_SDA GPIO_29 P3 64 GPIO_30 CAM_I2C_SCL GPIO_30 P3 65 UIM2_PRESENT KYPD_EN GPIO_52 P3 PM_KYPD_PWR_N PM_KYPD_PWR_N PMU CTR - DI 77 PM_VIB_DRV_N PM_VIB_DRV_N PMU CTR - PO 78 USB_HS_ID USB_HS_ID_MAIN USB - AI 79 PMU_MPP_2_PWM PWM_OUT PMU CTR - DO 80 GND 81 PMU_GPIO01 NFC_ENABLE PMU GPIO1 - DO-Z;DI 82 PM_RESIN_N PM_RESIN_N PMU CTR - DI PMU GPIO2 - DO-Z;DI PMU CTR - AO PO DI; B-PD:nppukp PI AI AI;AO AI 66
SHANGHAI SIMCOM LIMITED 102 MIPI_DSI0_ LANE1_P MIPI_DSI0_ LANE1_P 103 MIPI_DSI0_ LANE1_M MIPI_DSI0_ LANE1_M AI, AO AI, AO MIPI 104 MIPI_DSI0_ LANE0_P MIPI_DSI0_ LANE0_P AI, AO 105 MIPI_DSI0_ LANE0_M MIPI_DSI0_ LANE0_M AI, AO 106 GPIO_8 LCD_RST_N GPIO_8 107 VREG_L17_2P85V VREG_L17_2P85V POWER 108 GPIO_9 CAM_FLASH_EN GPIO_9 109 VREG_L6_1P8V VREG_L6_1P8V POWER 110 CCI_I2C_SDA I2C_SDA GPIO_10 111 CCI_I2C_SCL I2C_SCL GPIO_11 * 112 MCAM_RST_N MCAM_RST_N GPIO_35 * 113
SHANGHAI SIMCOM LIMITED 9 GPIO_93 OTG_EN GPIO_93 10 GPIO_94 ALSP_INT_N GPIO_94 * P3 11 GPIO_95 CHG_EN GPIO_95 * P3 12 GPIO_96 VBUS_OTG_EN GPIO_96 * P3 13 GPIO_97 NFC_DWL_REQ GPIO_97 * P3 14 GPIO_110 NFC_INT_N GPIO_110 * P3 15 GPIO_65 MAG_RESET GPIO_65 * P3 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 GND P3 DO; BB-PD:nppukp DI; BB-PD:nppukp DO; BB-PD:nppukp DO; BB-PD:nppukp DI; B-PD:nppukp DI; B-PD:nppukp DI; B-PD:nppukp Configurable I/O Configurable I/O Configur
SHANGHAI SIMCOM LIMITED 3 Electrical Specifications _______________________________________________________________________________ 3.1 Operating conditions 1.8 V digital I/O characteristics (P3) ): VDD_P3 GPIOs DualDual-voltage 1.8 V/2.
SHANGHAI SIMCOM LIMITED 3.2 Current test report This Current test report based on the EVB board, Vbat=3.8V. All values are typical unless otherwise specified. 1. 2. 3. During suspend (Airplane mode, no UIM, system in sleep mode): 2.9mA. During suspend (WIFI wake up, BT off, system in sleep mode): 3.0mA. Module power off (Do not remove the battery): 75uA(Without Vcoin); 250uA(With Vcoin).
SHANGHAI SIMCOM LIMITED 4 Application Interface Specifications _______________________________________________________________________________ 4.1 Power interface The power supply of SIMT1502 comes from PM8909. See Table4-1 Table4-1 Power source description Signal Pin# VREG_L11_2P95V VREG_L12_2P95V VREG_L17_2P85V VREG_L6_1P8V 61 85 107 109 Signal Pin# VBAT_SNS VBAT/VPH VBAT/VPH 88 92 124 Direction PI/PO PO PO PO PO Min 1.75 1.75 1.75 1.75 Voltage(V) Typ 2.95 1.8/2.95 2.85 1.8 Max 3.337 3.
SHANGHAI SIMCOM LIMITED 4.3 USB interface SIMT1502 contains a USB interface which support On-The-Go. It is compliant with the USB2.0 specification. The USB2.0 specification requires hosts to support all three USB speeds, low-speed (1.5Mbps), full-speed (12Mbps) and high-speed (480Mbps). See Table4-3 and Figure4-1 for more details. Table4-3 USB interface description Signal USB_DM USB_DP USB_HS_ID VBUS_USBIN Figure4-1 4.4 Pin# 44 45 78 87 Description USB 2.0 serial data minus USB 2.
SHANGHAI SIMCOM LIMITED Table4-4 Audio interface description Signal Pin# MIC3_IN MIC2_IN HS_DET SPKR_DRV_M SPKR_DRV_P EARO_M EARO_P MIC_GND MIC1_IN MIC_BIAS HPH_R HPH_REF HPH_L 9 10 11 12 13 14 15 16 17 18 19 20 21 Figure4-2 4.
SHANGHAI SIMCOM LIMITED MIPI_CSI1_CLK_P MIPI_CSI1_CLK_N CAM_PWDN CAM_I2C_SDA CAM_I2C_SCL CAM1_RST_N CAM1_STANDBY_N MIPI_CSI0_LN1_N MIPI_CSI0_LN1_P MIPI_CSI0_LN2_P MIPI_CSI0_LN2_N MIPI_CSI0_CLK_N MIPI_CSI0_CLK_P CAM_MCLK0 Figure4-3 7 8 121 63 64 112 113 115 116 117 118 119 120 122 MIPI camera serial interface 1 clock – positive MIPI camera serial interface 1 clock – negative Camera0 PWDN Camera I2C,SDA Camera I2C,SCL Camera 1 (rear camera) reset Camera 1 (rear camera) standby MIPI camera serial interface
SHANGHAI SIMCOM LIMITED 4.6 Display interface SIMT1502 contains one display interface. The interface use MIPI display serial interface, support up to four lanes. Support for the resolution of WVGA, qHD and 720p LCM.. The backlight circuit is not contained in SIMT1502, which must be designed in external circuit. See Table4-6 and Figure4-4for more details.
SHANGHAI SIMCOM LIMITED 4.7 CTP interface SIMT1502 contains one CTP interface, the panel is controlled by I2C bus. See Table4-7 and Figure4-5 for more details. Table4-7 Signal Pin# TS_INT_N TS_I2C_SDA TS_I2C_SCL TS_RST_N 33 34 35 36 Figure4-5 4.
SHANGHAI SIMCOM LIMITED Figure4-6 4.9 SD interface application diagram Sensors interface SIMT1502 support many sensors via I2C bus, the circuit structure is similar to camera interface. SIMT1502 does not contain necessary pull_up resistors internal, which must be designed in external circuit. 4.10 Side keys interface SIMT1502 contains a few keys interfaces, which can be used as functional side keys.
SHANGHAI SIMCOM LIMITED SIMT1502 must be provided voltage by external voltage source. See Table4-10 for more details. Table4-10 Battery connector description Signal Pin# BAT_THERM VBATT VBATT 90 88/92/124(No External Charging IC) 88 (With External Charging IC) 2/32/43/46/62/73/80/91/95/ 114/123/125/126/127/128 GND 4.12 Description Battery therm monitor Battery positive supply Battery positive supply Direction AI/AO AI AI AI Ground - I2C , UART and SPI interface 4.12.
SHANGHAI SIMCOM LIMITED 4.12.2 I2C SIMT1502 contains two groups special functional and four groups configurable I2C, which multiplexed with UART function. I2C pins use GPIOs configured as open-drain outputs; the pull-up resistor(2.2K) must be provided by external circuit(1.8V). High speed mode I2C running at 3.4 MHz.
SHANGHAI SIMCOM LIMITED 4.13 Signal Pin# GPIO_4 GPIO_5 GPIO_6 GPIO_7 GPIO_20 GPIO_21 GPIO_111 GPIO_112 GPIO_0 GPIO_1 GPIO_2 GPIO_3 26 27 24 25 38 39 28 29 49 50 51 52 Description SPI1 SPI1 SPI1 SPI1 SPI2 SPI2 SPI2 SPI2 SPI3 SPI3 SPI3 SPI3 MOSI MISO CS_N CLK MOSI MISO CS_N CLK MOSI MISO CS_N CLK Direction I/O O I O O O I O O O I O O Other interface 4.13.1 Camera flash Signal These camera flash signal provide flash and torch mode enable. The FLASH_NOW trigger the camera flash into torch mode.
SHANGHAI SIMCOM LIMITED VCOIN 4.13.4 89 Sense input or charge output AI,AO RF Signal input port SIMT1502 contains four RF signal input port: BT/WIFI. See Table4-16 and Figure4-8 for more details: Table4-17 RF Signal input port Signal Pin# RF_IN_2 WIFI_BT_RF 30 31 Description 5G_WIFI BT/WIFI Direction I/O AI,AO AI,AO If you want to use 5G_WIFI, you must use the RF Cable Line (IPX-3) connect the RF base, which close to BTB connect on SIMT1502.
SHANGHAI SIMCOM LIMITED 5 Mechanical Specification _______________________________________________________________________________ 5.1 Overview This specification defines a small form factor module for systems in which a Stamp hole package add-in module can not be used due to mechanical system design constraints. The specification defines a smaller module based on a single 124-pin Leadless Chip Carriers encapsulation for system interfaces by card edge type.
SHANGHAI SIMCOM LIMITED 5.2.2 SIMT1502 PCB details The following figures (Figure5-2) provide the printed circuit board (PCB) details required to fabricate the PCB. The PCB for this application is expected to be 1.2 mm thick. The steel net thickness is 0.12mm (Figure5-3). Figure5-2 SIMT1502 Pads The dimension tolerance is ± 0.005 mm (±0.2mil). Figure5-3 SIMT1502 Steel net The dimension tolerance is ± 0.005 mm (±0.2mil).
SHANGHAI SIMCOM LIMITED 5.3 System BTB connector specifications The SIMT1502 have a BTB connector In order to more GPIO interface 5.3.1 BTB connector The BTB connector is 30-pin card edge type connector. Detailed dimensions should be obtained from the connector manufacturer. Figure5-4 shows the BTB connector. We use AXE530127 as socket and AXE630127 as header.
SHANGHAI SIMCOM LIMITED 6 RF Specification _______________________________________________________________________________ 6.1 R&D parameters All measurements are taken at module RF I/O pins (pin 31 for BT/WIFI and RF connector for 5G_WIFI) with IQ2015. All typical performance specifications are based on operation at room temperature (+25°C) using default parameter settings and nominal supply voltages, such as VBAT = 3.8V. 6.1.
SHANGHAI SIMCOM LIMITED CHAN2 CHAN3 CHAN4 CHAN5 CHAN6 CHAN7 CHAN8 CHAN9 CHAN10 CHAN11 CHAN12 CHAN13 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467 2472 Table6-4 5G WiFi channels 20MHz 40MHz Channel Frequency Channel Frequency CHAN36 CHAN40 CHAN44 CHAN48 CHAN52 CHAN56 CHAN60 CHAN64 CHAN100 CHAN104 CHAN108 CHAN112 CHAN116 CHAN120 CHAN124 CHAN128 CHAN132 CHAN136 CHAN140 CHAN144 CHAN149 CHAN153 CHAN157 CHAN161 CHAN165 5180 5200 5220 5240 5260 5280 5300 5320 5500 5520 5540 5560 5580 5600 5620 56
SHANGHAI SIMCOM LIMITED 802.11B 802.11A / G 802.11N (HT20) 802.11N (HT40) Data Rate(Mbps) Modulation Format 1Mbps(DSSS) 2Mbps(DSSS) 5.5Mbps(CCK) 11Mbps(CCK) 6Mbps(OFDM) 9Mbps(OFDM) 12Mbps(OFDM) 18Mbps(OFDM) 24Mbps(OFDM) 36Mbps(OFDM) 48Mbps(OFDM) 54Mbps(OFDM) 6.5Mbps(MCS0) 13Mbps(MCS1) 19.5Mbps(MCS2) 26Mbps(MCS3) 39Mbps(MCS4) 52Mbps(MCS5) 58.5Mbps(MCS6) 65Mbps(MCS7) 13.5Mbps(MCS0) 27Mbps(MCS1) 40.5Mbps(MCS2) 54Mbps(MCS3) 81Mbps(MCS4) 108Mbps(MCS5) 121.
SHANGHAI SIMCOM LIMITED 37
SHANGHAI SIMCOM LIMITED 7 Declaration of Conformity (DoC) is in conformity with the relevant Union harmonization legislation: Radio Equipment directive: 2014 / 53 / EU with reference to the following standards applied: EN 301 489-1 V2.2.0 (2017-03); EN 301 489-17 V3.2.0 (2017-03) EN 55032:2015+AC:2016-07 EN 61000-4-2:2009 EN 61000-4-3:2006+A1:2008+A2:2010 EN 300 328 V2.1.1 (2016-11) EN 301 893 V2.1.
