Safety Instructions

ManualsBrandsShanghai Sunmi Technology ManualsPOS EquipmentWireless Data POS System

Table Of Contents

空白页面

Quick Start

NFC Reader (optional)

For reading NFC cards, like loyalty cards.

Printer

For printing receipts when the device is on.

Front Camera (optional)

For video conference, or photo/video taking.

Scan Button (optional)

Short press to enable barcode scanning function.

Type-C

For device charging and developer debugging.

Power Button

Short press: wake up the screen, lock the screen.

Long press: long press for 2-3 seconds to turn on

the device when it is oﬀ. Long press for 2-3 seconds

to select to power oﬀ or reboot the device when

it is on. Long press for 11 seconds to reboot a

device when the system is frozen.

Volume Button

For volume adjustment.

Scanner (optional)

For barcode data collection.

Rear Camera

For photo taking and quick 1D/2D barcode reading.

Pogo pin

For connecting a barcode scanning accessory,

or a cradle for communication and charging.

Nano SIM Card Slot

For installing the Nano SIM card.

PSAM Card Slot (optional)

For installing the PSAM card.

Micro SD Card Slot

For installing the Micro SD card.

SIM

PSAM

Printing Instructions

This device can load a 58mm thermal receipt or label

paper roll.

The paper roll spec is 57±0.5mm×Ø40mm.

· Please open the printer by lifting the lid (see ①). Please

do not force open the printer to avoid printhead gear

wear;

· Load the paper into the printer and pull some paper

outside the cutter following the direction shown in ②;

· Close the cover to complete paper loading (see ③).

Notice: If the printer prints blank paper, please check

whether the paper roll has been loaded in the correct

direction.

Tips: To clean a label printhead, it is recommended to

use a cotton swab dipped in alcohol or a alcohol prep

pad (75% isopropyl alcohol) to wipe the printhead.

Notices

Safety Warning

Connect the AC plug to the AC socket corresponding

to the marked input of the power adapter;

To avoid injury, unauthorized persons shall not

open the power adapter;

This is a Class B product. This product may cause

radio interference in living environments.

In that case, the user may be required to take

adequate measures against interference.

Battery replacement:

1.Explosion danger may arise if replacing with the

wrong battery!

2.The replaced battery shall be disposed of by

maintenance personnel, and please do not throw it

into ﬁre!

Signiﬁcant Safety Instructions

Do not install or use the device during lightning

storms to avoid the potential risks of lightning

shock;

Please turn oﬀ the power immediately if you notice

abnormal odor, heat or smoke;

The paper cutter is sharp, please do not touch!

Suggestions

· Do not use the terminal near water or moisture to

prevent liquid from falling into the terminal;

Do not use the terminal in extremely cold or hot

environments, such as near ﬂames or lit cigarettes;

Do not drop, throw or bend the device;

Use the terminal in a clean and dust-free environ-

ment if possible to prevent small items from falling

into the terminal;

Please do not use the terminal near medical

equipment without permission.

Statements

The Company does not assume responsibilities for

the following actions:

Damages caused by use and maintenance without

complying with the conditions speciﬁed in this

guide;

The Company will not assume any responsibilities

for the damages or problemscaused by optional

items or consumables (rather than the initial

products or approvedproducts of the Company).

The customer is not entitled to change or modify

the product without our consent.

The product’s operating system supports oﬃcial

systemupdates, but if you change the operating

system into a third party ROM system or alter the

system ﬁles by system cracking, it may cause

system instability and security risks and threats.

Disclaimer

As a result of product upgrading, some details in

this document may not match the product, and the

actual product shall govern. The Company reserves

the right of interpretation of this document. The

Company also reserves the right toalter this

speciﬁcation without prior notice.

Table for Names and Content Identiﬁcation of Toxic and

Hazardous Substances in this Product

indicates that the content of the toxic and hazardous substance in all

homogeneous materials of the component is below the limit speciﬁed

in SJ/T 11363-2006.

indicates that the content of the toxic and hazardous substance in at

least one homogeneous material of the component exceeds the limit

stipulated in SJ/T 11363-2006. However, as for the reason, because

there is no mature and replaceable technology in the industry at

present.

：

The products that have reached or exceeded environmental protection

service life should be recycled and reused according to the Regulations

on Control and Management of Electronic Information Products, and

should not be discarded randomly.

Part Name

Toxic or Hazardous Substances and Elements

Circuit Board Component

Structural Component

DBP

Packaging Component

Cr(VI)

PBB

PBDE DEHP BBP DIBPHg

T GUIDE

T5921

T5941

QUICK STAR

FCC Statement

Any Changes or modifications not expressly approved by the

party responsible for compliance could void the user’s

authority to operate the equipment.aut

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions:

(1)This device may not cause harmful interference, and

(2)This device must accept any interference received, including

interference that may cause undesired operation.

Note : This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates,uses and can radiate radio

frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that

interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for

help.

2.4G Wi-Fi:

2412-2462 MHz(802.11b/g/n20),2422-2452 MHz(802.11n40)

BLE(1Mbps)/BLE(2Mbps): 2402-2480 MHz

BT:2402-2480 MHz

5G Wi-Fi

Band 1: 5150~5250 MHz,Band 4: 5725~5850 MHz

GPRS/EGPRS 850: 824-849 MHz(TX), 869-894 MHz(RX)

GPRS/EGPRS 1900: 1850-1910MHz(TX), 1930-1990MHz(RX)GP

WCDMA Band II: 1850-1910 MHz MHz(TX), 1930-1990 MHz(RX)

WCDMA Band IV: 1710-1755 MHz(TX), 2110-2155MHz(RX)

WCDMA Band V: 824-849 MHz(TX), 869-894 MHz(RX)

LTE Band 2: 1850-1910 MHz(TX), 1930-1990MHz(RX)

LTE Band 4: 1710-1755 MHz(TX), 2110-2155MHz(RX)

LTE Band 5: 824-849 MHz(TX), 869-894 MHz(RX)

LTE Band 7: 2500-2570 MHz(TX), 2620-2690 MHz(RX)

LTE Band 12: 699-716 MHz(TX), 729-746 MHz(RX)

LTE Band 17: 704-716 MHz(TX), 734-746 MHz(RX)

LTE Band 25: 1850-1915 MHz(TX), 1930-1995 MHz(RX)

LTE Band 26: 814-849 MHz(TX), 859-849MHz(RX)

LTE Band 40 Lower: 2305-2315 MHz(TX), 2305-2315 MHz(RX)

LTE Band 40 Upper: 2350-2360 MHz(TX), 2350-2360 MHz(RX)

LTE Band 41: 2555-2655 MHz(TX), 2555-2655 MHz(RX)

LTE Band 66: 1710-1780 MHz(TX), 2110-2200 MHz(RX)

NFC:13.56 MHz

Wireless data POS System

Summary of content (2 pages)

PAGE 1
Quick Start Printing Instructions Notices 1 NFC Reader (optional) For reading NFC cards, like loyalty cards. 1 1 2 Printer For printing receipts when the device is on. 2 3 Front Camera (optional) For video conference, or photo/video taking. 3 4 4 5 6 7 4 Scan Button (optional) Short press to enable barcode scanning function. 6 Power Button Short press: wake up the screen, lock the screen. Long press: long press for 2-3 seconds to turn on the device when it is oﬀ.
PAGE 2
RF Exposure Information (SAR) : This device meets the government's requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard for wireless devices employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg.