Shark MODEL B2535H/1 OPERATING INSTRUCTIONS AND PARTS MANUAL R Read instructions carefully before attempting to assemble, install, operate or service this pressure washer. Failure to comply with instructions could result in personal injury and/or property damage! SPECIFICATIONS ● Pump Volume At Pump Head: 3.5 GPM/210 GPH ● Pump Pressure At Pump Head: 2500 PSI ● Machine Power: 9.0 HP Gasoline Engine, Manual Start ● Machine Weight: 145 Lbs. ● Shipping Weight: 185 Lbs.
WARNING Read and observe to prevent severe personal injury or property damage. ● Check hoses, fittings, wand, and trigger gun daily for signs of wear, cracks and looseness, and replace as required. ● Use extreme caution when moving pressure washer over rough or uneven surfaces. ● Do not point wand or trigger gun at yourself or at any person. Bodily injury may result from water under high pressure. ● ● Do not block or tie trigger gun in open position.
TRIGGER GUN WAND PRESSURE HOSE PRESSURE NOZZLE NOZZLE HOLDERS PRESSURE RELIEF VALVE ENGINE 24.5” PUMP THERMAL RELIEF VALVE 34” UNLOADER VALVE PRESSURE HOSE CONNECTOR 23.
ASSEMBLY 2. Assemble wand components as shown in Figure 3. NOTE: The pressure nozzle is not to be installed at this time. Unpacking Unpack carefully. Wear safety glasses or goggles while unpacking, assembling, or operating pressure washer. If there are missing components or hidden damage, immediately contact carrier concerning discrepancies. TRIGGER GUN Parts Included • • • • • • • Pressure Washer Pressure Hose Pressure Nozzle (4 Ea.
Venting DANGER: Do not run machine indoors or in an enclosed area, as exhaust fumes may be hazardous to your health. DANGER: Do not operate machine in areas where flammable vapors (gasoline, solvents, etc.) may be present, as this machine may ignite the vapors. CAUTION: All venting must be in accordance with applicable federal and state laws, and local ordinances. Consult local contractors.
5. Pull the rope starter slowly until resistance is felt, then pull briskly. Do not allow the rope starter to snap back against the engine. Return it gently to prevent damage to the starter. 6. When the engine star ts, move choke lever until engine runs smoothly. Move throttle lever to full throttle position. When engine warms, move choke lever to no choke position. NOTE: If engine fails to start, refer to Troubleshooting Guide in this manual. 7.
Proper Pump Care: • Do not pump acids. • Do not allow pump to run dry. • Winterize if storing in freezing temperatures, refer to Storage for details. • Use a water softener on the water system if known to be high in mineral content. • Flush the pressure washer system with antifreeze if storing for an extended period of time, refer to Storage for details. Gasoline Engine Refer to the provided gasoline engine manual for recommended maintenance.
TROUBLESHOOTING GUIDE SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION Gas engine will not run. Out of gas. Replenish supply. Use only recommended fuels. Refer to Before Starting under Operation. Fuel valve closed (if so equipped). Open valve. Loose spark plug wire. Reconnect. Choke or throttle set incorrectly. Refer to To Start under Operation. Engine ON/OFF switch in OFF position. Place engine ON/OFF switch in ON position. Low engine oil level. Replenish supply.
When ordering from your dealer, please provide the following: Model Number: B2535H/1 Machine Serial Number: ________________________________ Component Part Number: _______________________________ Description: __________________________________________ FOR HELP OR ADDITIONAL INFORMATION, CONTACT: Customer Service Department Shark Pressure Washers 21 Inverness Way East Englewood, CO 80112 1-800-771-1881 B2535H/1 OPTIONAL EQUIPMENT 280268 Detergent Injector Kit Shark B2535H/1 Page 9
1 38 25 2 5 35 3 6 14 24 36 26,27,28 33 9 7 13 10,11 12 4,29, 34,39 8 15,16 30,3 1,32 17 19,20 21,22, 23,37 18,19,20 Figure 6 - Machine Assembly Ref. No. Part No. Description Qty. Ref. No. Part No. Description Qty. 1 375441 Chassis 1 22 817322 Hubcap 2 2 Fig. 9 Trigger Gun/Wand Assembly 1 23 848616 Push Nut 5/8" 2 3 444469 Decal Shark Detergent 1 24 ■ Flat Washer 5/8" 4 4 Fig.
1 2,3 4 8,9 10 11 5 6 7 9,16 15 14 13 12 Figure 7 - Pump Assembly Ref. No. Part No. Description Qty. Ref. No. 1 HC340R Pump Fig.
Page 12 10 9 5 4 3 2 1 35 42 36 37 38 27 39 12 13 10 9 16 15 14 17 44 25 43 21 22 41 40 27 28 29 30 31 32 33 34 18 11 27 26 9 7 6 8 7 6 22 23 24 25 { 19 20 21 { Figure 8 - Pump, Exploded View Shark B2535H/1
Ref. No. Part No. Description Qty. Ref. No. Part No. Description Qty.
1 2 3 4 3 5,6,7,8 9 Figure 9 - Trigger Gun/Wand Assembly Ref. No. Part No. Description Qty. Ref. No. Part No. Description Qty. 1 860447 Trigger Gun Fig.
1 2 3 4 5 6 7 8 9 10 16 11 10 15 12 13 14 21 22 21 18 17 23 24 20 19 Figure 10 - Trigger Gun, Exploded View Ref. No. Part No. Description 1 817320 Valve Cap Qty. Ref. No. 1 15 Part No. Description 914141 Trigger Pin Qty.
WARRANTY Shark R SHARK ONE-YEAR LIMITED WARRANTY: Shark products are warranted by Shark Pressure Washers (Shark), to be free of defects in material and workmanship under normal use, for a period of ONE YEAR from the date of the original purchase. Items that fail due to normal wear such as pump seals, pump valves, unloader valves, detergent valves, water nozzles, quick couplings, hoses, gunjets, o-rings, etc. are not covered under this warranty.