CB OPERATOR’S MANUAL 98012620-1 LIS T E D ® MODEL # CB-301007D ORDER # 1.106-551.0 CB-402007A MODEL # CB-353007A ORDER # 1.106-556.0 1.106-552.0 CB-353007B 1.106-557.0 CB-402007B 1.106-553.0 CB-353007C 1.106-558.0 CB-402007C 1.106-554.0 CB-353007G 1.106-559.0 CB-402007H 1.106-555.0 CB-353007H 1.106-560.0 To locate your local Shark Commercial Pressure Washer Dealer nearest you, visit www.Sharkpw.com 9.801-262.
CONTENTS Important Safety Information 4-5 Component Identification 6 Assembly Instructions 7 Operating Instructions 8 Applying Detergent & General Operating Techniques 9 Shut Down & Clean-Up 10 Storage 10 Troubleshooting 11 Preventative Maintenance 12 Oil Change Record 12 Hose & Spray Gun Assembly & Parts List 13 Exploded View 14-15 Exploded View Parts List 16-17 VB8 Valve Exploded View and Parts List 18 Pump Exploded View and Parts List 19 Specifications Page 20-21 Multi-Roo
PRESSURE WASHER OPERATOR’S MANUAL INTRODUCTION & Important Safety Information Thank you for purchasing a Shark Pressure Washer. We reserve the right to make changes at any time without incurring any obligation. Owner/User Responsibility: The owner and/or user must have an understanding of the manufacturer’s operating instructions and warnings before using this pressure washer. Warning information should be emphasized and understood.
WARNING WARNING: Grip cleaning wand securely with both hands before starting. Failure to do this could result in injury from a whipping wand. WARNING RISK OF INJURY FROM FALLS WHEN USING LADDER. Trigger Gun Kicks back - Hold with both hands 17. Do not overreach or stand on unstable support. Keep good footing and balance at all times. 18. Do not operate this machine when fatigued or under the influence of alcohol, prescription medications, or drugs.
PRESSURE WASHER OPERATOR’S MANUAL Component Identification High Pressure Nozzle Soap Nozzle Water Supply Wand Quick Coupler On/Off Switch Garden Hose Inlet Spray Gun Discharge Nipple Garden Hose (not included) Trigger Swivel Connector Detergent Injector Hose Coupler Detergent Pick-up Tube High Pressure Hose 98012620-2 Detergent Injector - Allows you to siphon and mix detergents, when used with soap nozzle.
Spray Gun Nozzle Safety Latch Coupler High Pressure Hose STEP 1: Attach the high pressure hose to the spray gun using teflon tape on hose threads. Use safety latch to prevent from opening. STEP 2: Connect garden hose to the cold water source. Before installing nozzle, turn on water supply and run machine, allowing water to flush through the system until clear. 98012620-5 STEP 3: Insert nozzle into coupler. Release the coupler collar and push the nozzle until the collar clicks.
PRESSURE WASHER OPERATOR’S MANUAL Operating Instructions Cold Water Source Garden Hose 98012620-7 98012620-8 STEP 1: Connect garden hose to the cold water source and turn water on completely. Never use hot water. 98012620-9 STEP 2: Trigger the spray gun to eliminate trapped air then wait for a steady flow of water to emerge from the spray wand. Then install nozzle. On/Off Switch Safety Latch 98012620-11 98012620-10 STEP 4: Turn machine on by pushing switch at front of machine.
WARNING STEP 1: Use detergent designed specifically for pressure washers. Household detergents could damage the pump. Prepare detergent solution as required by the manufacturer. Fill a container with pressure washer detergent. Place the filter end of detergent suction tube into the detergent container. thermal pump protection If you run your pressure washer for 2 minutes without pressing the trigger on the spray gun, circulating water in the pump can reach high temperatures.
PRESSURE WASHER OPERATOR’S MANUAL shutting down and clean-up 98012620-16 98012620-17 STEP 1: Remove detergent suction tube from soap container and insert into one gallon of fresh water. Use black soap nozzle with detergent injector. Pull trigger on spray gun and siphon water for one minute. STEP 2: Turn off machine by pushing switch on front panel. Pump Water Inlet 98012620-18 STEP 3: Turn off water supply.
PROBLEM POSSIBLE CAUSE SOLUTION PUMP RUNNING NORMALLY BUT PRESSURE LOW ON INSTALLATION Pump sucking air Check water supply and possibility of air. Check valves sticking Check and clean or replace if necessary. Unloader valve seat faulty Check and replace if necessary. Nozzle incorrectly sized Check and replace if necessary. FLUCTUATING PRESSURE PRESSURE LOW AFTER PERIOD OF NORMAL USE Worn piston packing Check and replace if necessary. Valves worn Check and replace if necessary.
PRESSURE WASHER OPERATOR’S MANUAL Preventative Maintenance Preventative Maintenance This pressure washer was produced with the best available materials and quality craftsmanship. However, you as the owner, have certain responsibilities for the correct care of the equipment. Attention to regular preventative maintenance procedure will assist in preserving the performance of your equipment. Contact your dealer for maintenance.
PRESSURE WASHER Hose & Spray Gun Assembly 8 4 6 OPERATOR’S MANUAL 3 5 7 10 1 9 2 11 98012620-23 Hose & Spray Gun Assembly Parts List ITEM PART NO. DESCRIPTION QTY 1 9.802-166.0 Coupler, 3/8" Female 1 9.802-100.0 Quick Coupler O-Ring 1 2 8.739-125.0 Hose, 3/8" x 50', 1 Wire,Tuff-Flex 1 3 8.701-384.0 Gun, ST-1500, 5000 10.4 GPM 1 4 9.802-219.0 Wand w/Side Grip 1 5 8.712-398.0 Nozzle, Soap, Brass 1 6 Nozzle, See Exploded View Parts List 7 9.802-216.
PRESSURE WASHER Exploded View 10 Enlarged Reverse View 64 63 7 71 63 20 38 13 62 78 76 9 OPERATOR’S MANUAL 74 58 Time Delay Option 75 11 77 Auto Start Option 12 61 21 64 64 22 25 4 80 23 5 63 82 54 58 6 77 Auto Start Option 62 13 70 64 7 62 9 3 71 61 66 51 19 58 1 64 2 74 76 75 For Detail See Pump Assy. 22 12 25 24 98012620-24 15 8 14 23 14 9.801-262.0 • Shark CB • Rev.
PRESSURE WASHER Exploded View 27 OPERATOR’S MANUAL 79 43 46 68 44 17 50 40 41 16 42 73 26 28 45 50 49 39 69 29 53 46 32 37 72 57 56 31 59 65 33 30 67 60 47 55 59 78 35 98012020-25 34 52 36 80 81 19 48 50 18 15 9.801-262.0 • Shark CB • Rev.
PRESSURE WASHER OPERATOR’S MANUAL Exploded View Parts List ITEM PART NO. DESCRIPTION QTY 1 Unloader, See Specifications Pages 2 Pump, See Specifications Pages 3 Motor, See Specifications Pages 4 9.802-551.0 9.804-556.0 Transformer (552.0, 553.0 554.0, 556.0, 557.0, 558.0) Transformer (555.0, 559.0, 560.0) 1 1 5 8.933-007.0 Fuse, ATMR, 1 Amp, 600V (552.0, 553.0, 550.0, 556.0, 557.0, 559.0, 560.0) 2 9.802-462.0 Fuse, 1/2 Amp, 600V (554.0, 558.0) 2 6 9.802-463.
ITEM PART NO. DESCRIPTION QTY 39 9.800-064.0 Label 1 40 Bushing, See Specifications Pages 41 Bushing, See Specifications Pages 42 Pump Pulley, See Specifications Pages 43 Motor Pulley, See Specifications Pages 44 Belt, See Specifications Pages 45 9.802-522.0 Strain Relief, 1" 1 47 67 12 9.802-817.0 Washer, 3/8" x 1" Steel 48 9.802-710.0 Bolt, 5/16" x 1 NC (551.0) 9.802-720.0 Bolt, 3/8" x 1" NC, HH (552.0-560.0) 49 9.800-034.0 Label, Clear Lexan, 2-1/4" x 4-1/2" 50 66 9.
9.802-362.0 2 30 27 28 29 16 25 37 15 32 11 31 27 26 OPERATOR’S MANUAL PRESSURE WASHER VB8 Unloader Valve exploded view 12 10 24 9 23 39 13 6 22 14 8 13 21 5 7 20 38 40 36 18 4 35 19 17 34 33 3 2 1 VB8 Unloader Valve exploded view parts list ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY 1 60.0058.31 3/8 Bsp F Outlet Fitting 1 22 60.1210.31 Upper Frame 1 2 10.3070.02* O-ring 1.78 x 18.77 mm 2 23 14.7421.00 1/4" Ball 1 3 60.0053.
PRESSURE WASHER Specifications Pump Exploded View 2 1 3 14 10 4 2 9 Time Delay Shutdown Option 4 6 12 16 13 5 8 Auto Start/Stop Option 15 11 3 17 98012620-27 Pump Exploded View Parts List ITEM PART NO. DESCRIPTION QTY 1 8.750-299.0 Unloader, VRT3, 8 GPM @ 4500 PSI 2 9.802-039.0 Elbow, 1/2" JIC, 3/8", 90° 3 9.802-048.0 Swivel, 1/2" JIC x 3/8" Male 1 15 9.802-042.0 Elbow, 1/2" JIC x 3/8 Fem, 90° (Auto Start/Stop Option) 1 1 16 9.802-362.
PRESSURE WASHER Specifications Specifications Model Pump Pump Part No. Pump Pulley Pump Pulley Part No. Pump Bushing Bushing Part No. Size Voltage/ph Hz 1.106-551.0 KD3030R 9.804-006.0 AK74H 9.802-369.0 24MM 9.802-402.0 2HP 120V/1PH 60 1.106-552.0 KM4035R 8.751-189.0 2AK74H 9.802-369.0 24MM 9.802-402.0 6.2HP 230V/1PH 60 1.106-553.0 KM4035R 8.751-189.0 2AK74H 9.802-369.0 24MM 9.802-402.0 6.2HP 230V/3PH 60 1.106-554.0 KM4035R 8.751-189.0 2AK74H 9.802-369.
Motor Part No. Motor Pulley Motor Pulley Part No. 551.0 9.802-339.0 AK32x5/8 9.804-004.0 552.0 9.802-336.0 2AK56H 9.802.373.0 553.0 8.751-004.0 2AK56H 9.802-373.0 554.0 8.751-004.0 2AK56H 9.802-373.0 555.0 9.802-330.0 2AK56H 556.0 8.715-097.0 2BK52H 557.0 8.751-014.0 558.0 8.751-014.0 559.0 560.0 Motor Bushing Motor Part No. Belt Size Belt Part No. Contractor Part No. Overload Part No. N/A N/A AX40 (1) HX1-1/8" 9.802-400.0 AX42 (2) 9.804-005.0 8.724-268.0 N/A 9.
PRESSURE WASHER OPERATOR’S MANUAL Multi-Room Installation 98012020-26 22 9.801-262.0 • Shark CB • Rev.
PRESSURE WASHER KD.1 Pump exploded view 9.803-417.0 KD 3025.1 9.804-006.0 KD 3030.1 9.804-019.0 KD 4020.1 Item # Ft.-lbs 14 65 17 18 25 7.6 34 7 44 13 OPERATOR’S MANUAL TORQUE SPECS KD.1 Pump exploded view parts list item Part no. Description QTY item Part no. Description QTY 1 9.803-938.0 Crankcase 1 11* See Kits O-Ring Ø1.78 x 15.54 6 2* See Kits Plunger Oil Seal 3 12* See Kits Valve Assembly 6 3* See Kits O-Ring Ø1.78 x 28.30 3 13* See Kits O-Ring Ø2.62 x 18.
PRESSURE WASHER OPERATOR’S MANUAL KD.1 Pump exploded view parts list (cont) item Part no. Description QTY 33 8.933-010.0 Crankshaft Seal 1 34* See Kits Plunger Nut 3 35* See Kits Copper Spacer 3 36* See Kits Plunger, 15mm (3030) 3 See Kits Plunger, 18mm (4020, 3025) 3 37* See Kits Copper Spacer 3 38* See Kits O-Ring Ø1.78 x 5.28 3 39* See Kits Teflon Ring 3 40* See Kits Plunger Rod 3 41 9.803-965.0 Connecting Rod Pin 3 42 9.803-966.0 Connecting Rod 3 43 9.
PRESSURE WASHER KM.3 Series Pump Exploded View 8.751-186.0 KM3540R.3 8.751-187.0 KM4030R.3 8.751-188.0 KM4030L.3 8.751-189.0 KM4035R.3 8.751-190.0 KM4035L.3 8.751-191.0 KM5030R.3 8.751-192.0 KM5030L.3 Item # Ft.-lbs 14 75 15 30 23 8 33 9 43 13 48 7.6 OPERATOR’S MANUAL TORQUE SPECS KM.3 Series Pump Exploded View parts List item Part no. Description QTY item Part no. Description QTY 1 8.751-216.0 Crankcase 1 23 9.802-944.
PRESSURE WASHER OPERATOR’S MANUAL KM.3 Series Pump Exploded View parts List item Part no. Description QTY 36* See Kits Below Copper Spacer 3 37* See Kits Below O-Ring Ø1.78 x 7.66 3 38* See Kits Below Teflon Ring 3 39 8.751-224.0 Plunger Rod 3 40 9.803-158.0 Connecting Rod 3 41 8.751-228.0 Connecting Rod Pin 3 42 9.803-218.0 Spring Washer 6 43 9.803-238.0 Connecting Rod Screw 6 44 8.933-016.0 O-Ring, Ø2.62 x 126.67 1 45 8.751-229.0 Crankcase Cover 1 46 9.803-197.
8.750-297.0, 8 GPM, 2320 PSI 8.750-298.0, 8 GPM, 3630 PSI 8.750-299.0, 8 GPM, 4500 PSI ITEM PART NO. 20 25 18 8.750-713.0 8.750-712.0 Outlet Fitting Knob, Unloader 8.750-709.0 Repair Kit, VRT3, 2320/3630 PSI 8.750-710.
PRESSURE WASHER OPERATOR’S MANUAL LIMITED NEW PRODUCT WARRANTY—COMMERCIAL PRESSURE WASHERS Phone: 800-771-1881 Fax: 877-526-3246 www.sharkpw.com WHAT THIS WARRANTY COVERS All Shark pressure washers are warranted by Shark to the original purchaser to be free from defects in materials and workmanship under normal use, for the periods specified below.
www.sharkpw.com Shark CB 9.801-262.0 • Revised 5/13 • Printed in U.S.A.
