OPERATOR’S MANUAL MODEL DE-201007D DE-201507D DE-301007D DE-352007A ORDER # 1.106-061.0 1.106-062.0 1.106-063.0 1.106-064.0 To locate your local Shark Commercial Pressure Washer Dealer nearest you, visit www.shark-pw.com 8.919-015.
CONTENTS Important Safety Information ................................................................3-4 Component Identification ......................................................................... 5 Assembly Instructions .............................................................................. 6 Operating Instructions.............................................................................. 7 Applying Detergents & General Cleaning Techniques .............................
Thank you for purchasing this Pressure Washer. We reserve the right to make changes at any time without incurring any obligation. Owner/User Responsibility: The owner and/or user must have an understanding of the manufacturer’s operating instructions and warnings before using this pressure washer. Warning information should be emphasized and understood.
PRESSURE WASHER OPERATOR’S MANUAL IMPORTANT SAFETY INFORMATION WARNING WARNING: Grip cleaning wand securely with both hands before starting. Failure to do this could result in injury from a whipping wand. TRIGGER GUN KICKS BACK - HOLD WITH BOTH HANDS WARNING RISK OF INJECTION OR SEVERE INJURY TO PERSONS. KEEP CLEAR OF NOZZLE. 14. Inlet water must be clean fresh water and no hotter then 90°F. 15.
Detergent Injector Water Supply (not included) Pump Protector Pressure Nozzle Quick Coupler Unloader Soap Nozzle On/Off Switch Wand Hanger Pump Safety Latch Detergent Bucket (not included) PRESSURE WASHER OPERATOR’S MANUAL COMPONENT IDENTIFICATION Garden Hose (not included) GFCI Spray Gun and Wand Pump — Develops high pressure. Spray Gun — Controls the application of water and detergent onto cleaning surface with trigger device. Includes safety latch.
PRESSURE WASHER OPERATOR’S MANUAL ASSEMBLY INSTRUCTIONS Carriage Bolt Handle Alignment Holes Bolts Hose/Gun Storage Bracket Nut Nut Frame Assy. Studs STEP 1: Attach handle to the frame of the pressure washer. Note: It may be necessary to move the handle supports from side to side in order to align the handle so it will slide over the frame supports. STEP 2: Insert the carriage bolt through the holes from the outside of the unit and attach a nut from the inside of the machine. Tighten nuts.
Cold Water Source Garden Hose STEP 1: Connect garden hose to the cold water source and turn water on completely. Never use hot water. STEP 2: Trigger the spray gun to eliminate trapped air then wait for a steady flow of water to emerge from the spray nozzle. On/Off Switch STEP 3: Connect to appropriate power supply. Push reset button on GFCI. PRESSURE WASHER OPERATOR’S MANUAL OPERATING INSTRUCTIONS Safety Latch STEP 4: Turn machine on by turning switch at top of motor.
PRESSURE WASHER OPERATOR’S MANUAL DETERGENTS & GENERAL CLEANING TECHNIQUES WARNING WARNING: Some detergents may be harmful if inhaled or ingested, causing severe nausea, fainting or poisoning. The harmful elements may cause property damage or severe injury. STEP 1: Connect detergent injector to discharge nipple on machine. Connect high pressure hose to injector with quick coupler. (Check to make sure locking coupler sleeves are in proper position before applying water pressure).
On/Off Switch STEP 1: Remove detergent suction tube from container and insert into one gallon of fresh water. Slide nozzle forward for low pressure or use black detergent nozzle. Pull trigger on spray gun and siphon fresh clean water for one minute. Pump Water Inlet STEP 2: Turn off machine by turning switch to “OFF” switch. Pump Discharge Nipple STEP 5: Disconnect the garden hose from the water inlet on the machine. STEP 6: Disconnect the high pressure hose from pump discharge nipple.
PRESSURE WASHER Troubleshooting Guide TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION PUMP RUNNING NORMALLY BUT PRESSURE LOW ON INSTALLATION Pump sucking air Check water supply and possibility of air. Check valves sticking Check and clean or replace if necessary. Unloader valve seat faulty Check and replace if necessary. Nozzle incorrectly sized Check and replace if necessary. Worn piston packing Check and replace if necessary. Valves worn Check and replace if necessary.
PREVENTATIVE MAINTENANCE This pressure washer was produced with the best available materials and quality craftsmanship. However, you as the owner have certain responsibilities for the correct care of the equipment. Attention to regular preventative maintenance procedures will assist in preserving the performance of your equipment. Contact your dealer for maintenance. Regular preventative maintenance will add many hours to the life of your pressure washer.
PRESSURE WASHER EXPLODED VIEW 2 3 OPERATOR’S MANUAL 1 9 4 10 15 16 17 23 6, 7 62 N MOTO IVO TO DE RESET LOAD REPOSIC ION 14, 28 48 14, 28 63 34 MOT OR 21 22 52 64 18, 19 1 33 DEPO PUSH OVE SITIVO TO RLO DE RESE REPOS T AD ICION 10 Models 253.0, 064.0 40 12 22 R DEPOSIT PUSH OVER 17 N FF Models 251.0, 252.0, 062.0, 063.0 11 21 27 16 O O 50 24 25 15 5 20 O FF 26 O 5 39 31 32 35 8 20 36 61 39 37 40 38 8 40 44 54 39 29 60 20 42 Models 250.0, 061.
ITEM PART NO. 1 DESCRIPTION QTY 9.104-016.0 NOZZLE KIT 3.25 (23326) 1 ITEM PART NO. DESCRIPTION QTY 16 9.802-478.0 Lid, Plastic, Carlon E9801 Box 1 (251.0, 252.0, 253.0, 062.0, 063.0, 064.0 ) 17 9.802-477.0 Box, Plastic, Carlon E9801, w/o Lid (251.0, 252.0, 253.0, 062.0, 063.0, 064.0) 9.804-624.0 Nozzle, 1504, Yellow (250.0, 061.0) 1 9.804-625.0 Nozzle, 2504, Green (250.0, 061.0) 1 Nozzle, 4004, White (250.0, 061.0) 1 18 9.802-436.0 21" Nozzle, 0004, Red (250.0, 061.
PRESSURE WASHER OPERATOR’S MANUAL EXPLODED VIEW PARTS LIST ITEM PART NO. DESCRIPTION QTY 39 9.802-706.0 Bolt, Carriage, 1/4"-20 x 1-3/4" 6 40 9.802-802.0 Washer, 1/4" Flat 6 41 9.802-776.0 Nut, 5/16" ESNA, NC 4 42 9.803-119.0 Handle, Lower Grab, Chrome 1 43 9.803-114.0 Retainer Bracket, Handle, Black 2 44 9.802-728.0 Bolt, 3/8" x 2" 4 45 9.802-730.0 Bolt, 3/8" x 2-1/2" 2 46 9.802-817.0 Washer, 3/8" x 1" 2 47 9.802-066.0 Pad, Soft Rubber, 50 Duro 2 48 9.802-807.
PRESSURE WASHER OPERATOR’S MANUAL HOSE AND SPRAY GUN ASSEMBLY 5 4 3 6 7 8 1 9 2 10 9 11 HOSE AND SPRAY GUN ASSEMBLY PARTS LIST ITEM PART NO. DESCRIPTION 1 9.802-166.0 9.802-100.0 Coupler, 3/8" Female Quick Coupler O-Ring QTY 1 1 2 8.739-125.0 Hose, 3/8" x 50', 1 Wire, Tuff-Flex 1 3 9.802-223.0 Spray Gun, Shut-Off 1 4 9.802-220.0 Wand, Straight 1 5 9.802-164.0 9.802-096.0 Coupler, 1/4" Female Quick Coupler O-Ring 1 1 6 Nozzle, See Page 13 For Size 7 8.712-398.
PRESSURE WASHER Specifications UU1 UNLOADER EXPLODED VIEW 9.175-018.0 UU1 3500PSI, UNIVERSAL UNLOADER (SPARE) 21 2 3 14 20 10 16 18 5 1 15 19 6 27 7 25 23 25 4 24 8 22 27 28 26 13 15 26 9 12 17 27 23 11 UU1 UNLOADER EXPLODED VIEW PARTS LIST ITEM PART # 1 KIT QTY 8.749-792.0 Piston housing ITEM PART # DESCRIPTION KIT QTY 1 17 2 Piston C 1 18 1 Piston O-ring back up A 1 O-ring backup 6X 1.45X 1.68 A 3 C 1 9.149-006.0 Sliding connector guide 1 4 8.749-796.
9.803-814.0 KE 2020F 9.803-815.0 KE 2020S 9.803-816.0 KE 2825F 9.803-817.0 KE 2825S 9.803-818.0 KE 3525F TORQUE SPECS Item # Ft.-lbs 14 65 17 18 25 7.6 36 8 38 7 48 13 PRESSURE WASHER OPERATOR’S MANUAL KE.1 SERIES PUMP EXPLODED VIEW KE.1 SERIES PUMP EXPLODED VIEW PARTS LIST ITEM PART NO. DESCRIPTION 1 9.803-938.0 Crankcase 1 16 9.803-951.0 Brass Plug G1/4 1 2* 9.804-586.0 Plunger Oil Seal 3 17 9.803-952.0 Manifold Stud Bolt 8 3* See Kit Below O-Ring Ø 1.78 x 28.
PRESSURE WASHER OPERATOR’S MANUAL KE.1 SERIES PUMP EXPLODED VIEW PARTS LIST ITEM PART NO. DESCRIPTION 36 9.804-584.0 Flange Screw 37 9.804-585.0 QTY 4 Crankshaft Seal 1 38* See Kit Below Plunger Nut 3 39* See Kit Below Copper Spacer 3 40* See Kit Below Plunger 15mm (2020F, 2825F, 3525F) 3 See Kit Below Plunger 18mm (2020S, 2825S) 3 41* See Kit Below Copper Spacer 3 42* See Kit Below O-Ring Ø1.78 x 5.28 3 43* See Kit Below Teflon Ring 3 44 9.803-964.0 Plunger Rod 3 45 9.
HD Models Machine Model Pessure Nozzle Pump Pump Unloader Motor Part # Hp Motor GPM (PSI) Size Hose p/n Part # Model 1.575-250.0 2.0 1000 3.75 9.802-233.0 9.803-814.0 KE2020F 9.175-018.0 1-1/2 9.802-338.0 Part # 1.575-251.0 1.9 1500 3.0 9.802-233.0 9.803-814.0 KE2020F 9.175-018.0 2 9.802-339.0 1.575-252.0 2.8 1000 5.5 9.802-233.0 9.803-816.0 KE-2825-F 9.175-018.0 2 9.802-339.0 1.575-253.0 3.5 2000 5.0 9.802-233.0 9.803-818.0 KE-3525-F 9.175-018.0 5 9.
Phone: 800-771-1881 Fax: 877-526-3246 www.shark-pw.com WHAT THIS WARRANTY COVERS All Shark pressure washers are warranted by Shark to the original purchaser to be free from defects in materials and workmanship under normal use, for the periods specified below. This Limited Warranty, subject to the exclusions shown below, is calculated from the date of the original purchase, and applies to the original components only.
www.shark-pw.com Form # 8.919-015.0 • Revised 01/11 • Printed in U.S.A.
