S E L F - E M P T Y Robot Vacuum RV1000AE Series OWNER’S GUIDE
IMPORTANT SAFETY INSTRUCTIONS PLEASE READ CAREFULLY BEFORE USE • FOR HOUSEHOLD USE ONLY If the charging cable plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT force into outlet or try to modify to fit. WARNING To reduce the risk of fire, electric shock, injury, or property damage: GENERAL WARNINGS When using an electrical appliance, basic precautions should always be followed, including the following: 1.
18. DO NOT use to pick up: a) Liquids b) Large objects c) H ard or sharp objects (glass, nails, screws, or coins) d) Large quantities of dust (drywall dust, fireplace ash, or embers). DO NOT use as an attachment to power tools for dust collection. e) S moking or burning objects (hot coals, cigarette butts, or matches) f) Flammable or combustible materials (lighter fluid, gasoline, or kerosene) g) T oxic materials (chlorine bleach, ammonia, or drain cleaner) 19.
GETTING TO KNOW YOUR SHARK IQ ROBOT™ Charge Indicator Lights Error Indicator Light Wi-Fi Indicator Light ! Front Bumper Clean Button Dock Button Navigation Module Dust Bin Release Tabs Power Button Docking Sensor Debris Discharge Opening Cliff and Boundary Sensors Side Brush Battery Door Self-Cleaning Brushroll Front Caster Wheel Drive Wheel Brushroll Door Charging Contact Robot Dust Bin and Filter s h a r kc l e a n .
GETTING TO KNOW YOUR SHARK IQ ROBOT™ Base Dust Bin Release FRONT Base Dust Bin Fill Window Dust Bin Empty Button Charging Base Debris Intake Charging Contact Charging Contact BACK Base Dust Bin Pre-Motor Filter Housing Charging Base Post-Motor Filter Access Door Power Cord Connection Charger Cord Wrap s h a r kc l e a n .
BASE SETUP 3 ft. 5 ft. 3 ft. The Self-Empty Base charges your robot and holds dirt and debris from up to 30 days of cleaning. Select a permanent location for the base, because every time you relocate it, your robot will have to completely re-map your house. Choose a level surface in a central area. Remove any objects that are closer than 3 feet from either side of the base, or closer than 5 feet from the front of the base.
CHARGING IMPORTANT: The Shark IQ Robot™ has a pre-installed rechargeable battery. Battery should be fully charged before using. It may take up to 6 hours to fully charge. To charge, the Power button on the side of the robot must be in the ON position (I). The robot will beep when charging begins. When the cleaning cycle is complete, or if the battery is running low, the robot will search for the base. If your robot doesn’t return to the base, its charge may have run out.
CHARGE INDICATOR LIGHTS In Use Full Charge (Blue) Partial Charge (Blue) Low Charge (Red) While Charging (Blue) No Charge or Off The blue indicator lights on the robot show how much charge is remaining. While the robot is charging, both blue LED lights will flash. When charging is complete, both blue lights will illuminate steadily. It may take up to 6 hours to fully charge your robot. NOTE: If the low charge light is blinking red, there is not enough charge for the robot to return to the base.
BUTTONS AND INDICATOR LIGHTS CHARGE INDICATOR LIGHTS Display the amount of charge remaining in the battery. ! “!” ERROR INDICATOR See Troubleshooting section for full list of error codes. WI-FI INDICATOR Blue light: connected to Wi-Fi. Red light: not connected. Flashing blue: setup mode. No light: not set up yet. NAVIGATION MODULE Please keep clear and do not cover. Upward-facing sensor that identifies unique reference points to aid advanced navigation.
PREP YOUR HOME Your robot uses an array of sensors to navigate around walls, furniture legs, and other obstacles while it cleans. To prevent the robot from bumping into objects or navigating to areas you don't want it to, use the included BotBoundary® strips. For best results, prepare your home as indicated below, and schedule a daily cleaning to ensure all floor areas are regularly maintained. NOTE: Scheduling can only be done in the app.
History Schedule Dining Room Living Room Kitchen Control Shark Maps MAPPING AND NAVIGATION As it cleans, your robot will create a map of your home. It may take several cleanings for the robot to finish its mapping. Once mapping is complete, an Interactive Map of your floor plan will be available on the app. The interactive map in the app allows you to name rooms, then select which rooms to clean, and send the robot to clean one specific location.
USING THE SHARK IQ ROBOT™ Please visit sharkclean.com/app or call 1-888-228-5531 for answers to all your app questions. USING THE SHARKCLEAN™ APP AND VOICE CONTROLS Get the most out of your Shark IQ Robot™ with these app features: OPTIONS •C ontrol From Anywhere Wherever you are, you’re in control of your robot. RUMPELSTILTSKIN History Kitchen EDIT Schedule • Scheduling Set cleanings for any time, any day. • Room Select Send your robot directly to any room on that floor.
MAINTENANCE CAUTION: Turn off power before performing any maintenance. EMPTYING THE ROBOT DUST BIN Press the Dust Bin Release Tabs and slide out the dust bin. To avoid spills, be sure to hold the dust bin in an upright position. Pinch and lift to open the lid. Empty debris and dust into trash. Look between the filter and plastic shield and make sure there is no debris buildup. Remove and clean any debris build-up as needed with a dry cloth or soft brush. s h a r kc l e a n .
MAINTENANCE EMPTYING THE BASE DUST BIN The Base Dust Bin holds up to 30 days' worth of dust and debris. Empty the bin when the debris level approaches the max fill line. To detach it, press the Release button on top of the handle, then tilt the bin and lift it off. s h a r kc l e a n . c o m To empty the bin, hold it over a trash can and press the Empty button on the side.
MAINTENANCE CLEANING AND REPLACING THE ROBOT FILTER For optimal suction power, regularly clean and replace the filter inside the robot's dust bin. See sharkaccessories.com for replacement filters. IMPORTANT: DO NOT use water to clean the robot filter. Remove and empty the robot dust bin. Clean any hair or debris off the Anti-Tangle Comb on the back of the dust bin. Pull filter out of the dust bin by the tabs. Lightly tap the filter to remove dust and debris.
MAINTENANCE CLEANING AND REPLACING THE BASE FILTERS Regularly clean and replace your filters to keep your vacuum's suction power optimal. To clean filters, rinse with cold water ONLY to prevent damage from cleaning chemicals. Allow all filters to air-dry for at least 24 hours before reinstalling them to prevent liquid from being drawn into electric parts. IMPORTANT: DO NOT use soap when cleaning the filters.
MAINTENANCE SELF-CLEANING BRUSHROLL The Self-Cleaning Brushroll removes debris over time as it cleans. If some debris remains wrapped around the brushroll, continue cleaning to allow the brushroll to remove it. If some debris remains on the brushroll after continued cleaning, follow the steps below to remove it. To access the brushroll, push up on the tabs on the brushroll access door, then lift off the door. Lift out the brushroll. Remove the cap on the end of the brushroll.
MAINTENANCE CLEANING SENSORS AND CHARGING PADS CLEAN SENSORS AND CHARGING PADS AS NEEDED. With a dry cloth, gently dust off the sensors and pads located on the bottom of the robot and on the base. IMPORTANT: The robot uses cliff sensors to avoid stairs and other steep drops. Sensors may work less effectively when they are dirty. For best results, clean sensors regularly. CLEANING SIDE BRUSHES CLEAN SIDE BRUSHES AS NEEDED. Carefully unwind and remove any string or hair wrapped around brushes.
MAINTENANCE CLEANING THE WHEELS REMOVE AND CLEAN THE FRONT CASTER WHEEL AS NEEDED. See sharkaccessories.com for replacement parts. Pull the Front Caster Wheel from its housing and remove any debris buildup. Clean the wheel housing, then reinsert the caster wheel. NOTE: Tools may be required to pry off front caster wheel. NOTE: Brush not included. Periodically clean the drive wheels and the housing around them. To clean, rotate each drive wheel while dusting. s h a r kc l e a n .
REPLACEMENT PARTS REPLACEMENT PARTS: ROBOT REPLACEMENT PARTS: BASE Filter RVFFK950 Robot Dust Bin 101KY1000AE Base Dust Bin 104KY1000AE Self-Cleaning Brushroll 103KY1000 Battery RVBAT850 Self-Empty Base XSKAEDOCK Brushroll Door 109KY1000 Power Cord ADAP1000AE Pre-Motor Foam & Felt Filter Kit 106KY1000AE Side Brushes 102KY1000 Replacement Post-Motor Filter 107KY1000AE NOTE: To order replacement parts and filters, visit sharkaccessories.com. s h a r kc l e a n .
MAINTENANCE CAUTION: Turn off power before performing any maintenance. TROUBLESHOOTING If any error lights are illuminated or flashing on your Shark IQ Robot™, see the error code chart below: ERROR CODE SOLUTION CLEAN (RED) flashing Robot may be stuck on an obstacle. Move robot to a new location on a level surface. DOCK (RED) flashing Front bumper may be jammed. Clean the bumper and make sure it moves in and out freely. CLEAN (BLUE) + DOCK (RED) solid BotBoundary® error.
END-USER LICENSE AGREEMENT FOR SHARKNINJA SOFTWARE IMPORTANT: PLEASE READ THE TERMS AND CONDITIONS OF THIS LICENSE AGREEMENT CAREFULLY BEFORE CONTINUING WITH THIS PROGRAM INSTALL OR USE OF THIS PRODUCT: SharkNinja Operating LLC’s (“SharkNinja”) End-User License Agreement (“EULA”) is a legal agreement between You (either a single entity or an individual) and SharkNinja for SharkNinja’s Software Applications, including those installed by You onto your SharkNinja products or already installed on your device, i
END-USER LICENSE AGREEMENT FOR SHARKNINJA SOFTWARE 5.6 You will not use the Ayla Application Libraries or Ayla Embedded Software to attempt to gain unauthorized access to or use of the systems/services of SharkNinja’s other licensors; nor will You transmit viruses, worms, Trojan horses, time bombs, spyware, malware, cancelbots, passive collection mechanisms, robots, data mining software, or any other malicious or invasive code or program into the systems/services of SharkNinja’s other licensors. 5.
ONE (1) YEAR LIMITED WARRANTY The One (1) Year Limited Warranty applies to purchases made from authorized retailers of SharkNinja Operating LLC. Warranty coverage applies to the original owner and to the original product only and is not transferable.
NOTES s h a r kc l e a n .
NOTES s h a r kc l e a n .
REGISTER YOUR PURCHASE registeryourshark.com RECORD THIS INFORMATION Model Number: ������������������������ Date Code: ���������������������������� Date of Purchase: ���������������������� (Keep receipt) Store of Purchase: ���������������������� TIP: You can find the model and serial numbers on the QR code label on the bottom of the robot. EXPECTED PERFORMANCE Expected runtime: 60 minutes Expected charging time: 6 hours PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE.
FCC WARNINGS This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
