WWW.SHARKCLEAN.COM LIGHT & EASY™ STEAM MOP S3251 OWNER’S GUIDE S3251_11_ENG_IB_101117.
IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS For Household Use Only 1. Use the system only for its intended use. 2. DO NOT use outdoors. 3. DO NOT leave the appliance unattended when plugged in. Always unplug the power cord from the electrical outlet when not in use and before servicing. TO REDUCE 4. DO NOT allow the appliance to be used as a toy. Close THE RISK OF FIRE, ELECTRIC attention is necessary when SHOCK OR INJURY READ ALL used by or near children, pets INSTRUCTIONS BEFORE USING or plants.
11. DO NOT unplug by pulling on power cord. To unplug, grasp the plug not the power cord. Do not use extension cords or outlets with inadequate current carrying capacity. 12. DO NOT put any objects into openings. Do not use with any opening blocked. 13. DO NOT put hands or feet under the steam mop. Unit gets very hot. 14. Use ONLY on flat, stable horizontal surfaces. Do not use on walls, counters, windows, chairs or tables. 15.
Quick Start fig. 3 fig. 2 fig. 1 1 2 ASSEMBLE Fit together the extension tubes as shown in the illustration. (fig. 1) Place the micro-fiber cleaning pad underneath the mop head, with quick fastener strips facing up. Simply press the mop to the pad to attach it. (fig. 2) 3 FILL Remove the cap to fill the water tank. Use the filling flask and funnel to fill the tank with water to the “MAX” fill line. Replace the water tank cap. (fig. 3) TOLL FREE: 1-800-798-7398 S3251_11_ENG_IB_101117.
Quick Start QUICK TIP: For easier pushing and pulling, extend the handle length. fig. 4 STEAM CLEANING 4 For your comfort, you can adjust the height of the mop. Just lift the latch on the tube 90 degrees to the open position. Holding the handle, extend the tube to the desired height and then close the latch to the locked position. 5 Plug in the mop. Wait 30 seconds for the unit to heat up and the steam to be ready. NOTE: Do not leave your Steam Mop unattended during use.
This manual covers model number: S3251 11 TECHNICAL SPECIFICATIONS Voltage: 120V., 60Hz. Power: 1550 Watts Water Capacity: 250 ml (8 oz.) TOLL FREE: 1-800-798-7398 S3251_11_ENG_IB_101117.
Contents Thank you for purchasing the Shark® Light & Easy™ Steam Mop. GETTING STARTED.................................................................. 2 USING YOUR STEAM MOP....................................................6 STORAGE AND CARE OF YOUR STEAM MOP............. 8 TROUBLESHOOTING............................................................ 10 WARRANTY AND REGISTRATION....................................13 www.sharkclean.com S3251_11_ENG_IB_101117.
Getting Started When assembling your steam mop there may be a little water in or around the water tank. This is because we test all our steam mops 100% before you buy them, so you get a quality Shark® Light & Easy™ Steam Mop. a b c b e d f fig. 1 FIRST THINGS FIRST, YOU NEED TO KNOW WHAT’S IN THE BOX YOU JUST OPENED: a Upper Extension Tube b Lower Extension Tube (Telescopic) c Steam Mop Base d 2 All-Purpose Cleaning Pads e Filling Flask ASSEMBLY 1 Remove all the parts from the package.
English fig. 3 fig. 2 3 Insert the assembled handle piece into the steam mop base. Push the tube base together until you hear a click. (fig. 2) IMPORTANT: Never use the Light & Easy™ Steam Mop without attaching a micro-fiber cleaning pad to avoid damage to your floor and mop. 4 For your comfort, you can adjust the height of the mop. Just lift the latch on the tube 90 degrees to the open position. Holding the handle, extend the tube to the desired height and then close the latch to the locked position.
Getting Started Your micro-fiber cleaning pads should be replaced every 3 months to maximize cleaning performance. fig. 1 ATTACHING THE MICRO-FIBER PAD 1 Place the micro-fiber cleaning pad on the floor with the quick fastener strips facing up. Place the Light & Easy™ Steam Mop on the top of the pad to attach. (fig. 1) Replacement micro-fiber pads are available at www.sharkclean.com or by calling 1-800-798-7398. IMPORTANT: Only add water to the tank.
English Calcium and mineral deposits can build up and impact the performance of your steam mop over time. To extend the life of your product we recommend that you use distilled water or Shark®’s Water Filtration Bottle. Visit www. sharkclean.com to order. fig. 2 fig. 3 FILLING THE WATER TANK IMPORTANT: Unplug the Light & Easy™ Steam Mop before filling the water tank with water. (fig. 2) 1 Remove the water tank cap by turning it counter-clockwise to the unlocked position. (fig.
Using Your Light & Easy™ Steam Mop fig. 1 When you use your steam mop for the first time or if you have not used the unit in awhile, it may take a minute or two for the water to travel through the pump and into the heater to create steam. Get it started by pumping the handle a few times. If you have waited a few minutes and you still do not see any steam, reference the troubleshooting section on page 10. fig. 2 fig.
English If your Light & Easy™ Steam Mop stops steaming, it could be out of water. Unplug the power cord from the electrical outlet and refill the water tank at anytime. fig. 4 fig. 5 2 Wait 30 seconds for the boiler to heat the water. Pump the handle a few times to prime the pump, activate steam and moisten the micro-fiber pad. (fig. 4) 3 Mop with a forward and backward motion to customize steam output automatically. (fig.
Care of Your Light & Easy™ Steam Mop fig. 1 fig.2 AFTER USE AND STORAGE 1 When you have finished using the Light & Easy™ Steam Mop, unplug the cord from the outlet and place the mop into the upright position (fig. 1) and let the unit cool 3-5 minutes. Release steam by pumping the handle several times. 2 Carefully separate micro-fiber cleaning pad from steam mop, avoiding contact with the hot pad or dirt. (fig. 2) fig.3 4 To store the cooled Shark® Light & Easy™ Steam Mop, hang on a large hook. (fig.
English Care of Your Light & Easy™ Steam Mop fig. 4 fig. 5 CARE OF YOUR MICRO-FIBER CLEANING PAD 1 Wash pads in warm water. Wash separately from other laundry. Only use liquid detergent (no powder detergent). Do not use fabric softeners. Line dry or dry on a low dryer setting. (fig. 4) 2 If there are loose threads on the pad carefully cut the threads with scissors. Do not pull on them or cut at the base. (fig.
Trouble Shooting PROBLEM POSSIBLE REASONS & SOLUTIONS The Light & Easy™ Steam Mop will not turn-on. Your steam-mop should be securely plugged into a 120V AC electrical outlet only. Check your fuse or breaker. If your unit still does not work, call 1-800-798-7398. Light & Easy™ Steam Mop will not make steam. Is there water in the water tank? If not, add water to your steam mop following instructions on page 5. Light & Easy™ Steam Mop leaves water on the floor.
English Notes www.sharkclean.com S3251_11_ENG_IB_101117.
Notes 12 TOLL FREE: 1-800-798-7398 S3251_11_ENG_IB_101117.
English ONE (1) YEAR LIMITED WARRANTY EURO-PRO Operating LLC warrants this product to be free from defects in material and workmanship for a period of one (1) year from the date of the original purchase, when utilized for normal household use, subject to the following conditions, exclusions and exceptions. If your appliance fails to operate properly while in use under normal household conditions within the warranty period, return the complete appliance and accessories, freight prepaid.
U.S.: EURO-PRO Operating LLC Newton, MA 02459 Canada: EURO-PRO Operating LLC 4400 Bois Franc Ville St. Laurent, Québec H4S 1A7 1-800-798-7398 www.sharkclean.com COPYRIGHT© EURO-PRO OPERATING LLC 2010 PRINTED IN CHINA S3251.E.101117 Illustrations may differ from actual product. S3251_11_ENG_IB_101117.
