Specifications

STP SERIES PRESSURE WASHER OPERATOR’S MANUAL
5
Shark STP • 8.914-341.0 / 97-6153 • REV. 6/07
WARNING
RISK OF FIRE.
DO NOT ADD FUEL
WHEN OPERATING
MACHINE.
WARNING
PROTECTIVE
EYEWEAR AND CLOTH-
I
NG MUST
BE WOR
N.
WARNING
RISK OF
ASPHYXIATION.
U
SE ONLY IN A WELL
VE
NTILATED AREA.
WARNING: High pressure spray
can cause paint chips or other
particles to become airborne and
fly at high speeds.
9. Eye safety devices must be
worn when using this equip-
ment.
WARNING: Risk of asphyxiation
— Use this product only in a well
ventilated area.
10. W
hen the machine is work-
ing, do not cover or place in a
closed space where ventilation
is insufficient.
WARNING: Risk of fire. Do not
add fuel when the machine is
operating or still hot.
11.
Machines with a spray gun
should not be operated with
the spray gun in the off position
for extended periods of time
as this may cause damage
to the pump. Check to make
sure burner shuts off when spray gun trigger is
closed.
12. Protect from freezing.
13. To prevent a serious injury, make certain quick
coupler on discharge hose has locked before using
pressure washer.
14. Do not allow acids, caustic or abrasive fluids to pass
through the pump.
15. Inlet water must be cold and clean fresh water.
16. Do not allow CHILDREN to operate the pressure
washer at any time. THIS MACHINE MUST BE
ATTENDED DURING OPERATION.
17. The best insurance against an accident is precau-
tion, and knowledge of the machine.
18. Do not operate this product when fatigued or under
the influence of alcohol or drugs. Keep operating
area clear of all persons.
19. We will not be liable for any changes made to our
standard machines, or any components not pur-
chased from us.
20. Do not overreach or stand on unstable support. Keep
good footing and balance at all times.
21. Follow the maintenance instructions specified in the
manual.
22. When making repairs disconnect from electrical
source.
2
3. Turn burner off and open spray gun to allow water to
flow and cool coil to 100°F before turning machine
off.
24. Before disconnecting high pressure hose from
hot water outlet, turn off burner to allow water to cool
to 100°F, then turn off pump motor and water sup-
ply and operate spray gun to relieve back pressure
in hose. This will prevent coil damage from thermal
expansion.
CAUTION: This machine produces hot water and
must have insulated components attached to protect
the operator.
INSTALLATION
Place machine in a convenient location providing ample
support, draining and room for maintenance.
This machine is intended for indoor use. Machine
must be stored indoors when not in use.
Location:
The location should protect the machine from damag-
ing environmental conditions, such as wind, rain, and
freezing.
1. This machine should be run on a level surface where
it is not readily influenced by outside sources such
as strong winds, freezing temperatures, rain, etc.
It should be located to allow accessibility for refill-
ing of fuel, adjustments and maintenance. Normal
precautions should be taken by the operator of the
machine to prevent moisture from reaching the
electrical controls.
2. It is recommended that a partition be made between
the wash area and the machine to prevent water
spray from coming in contact with the machine. Ex-
cess moisture reaching any electric components or
electrical controls will reduce machine life and may
cause electrical shorts.
3. During installation of the machine, beware of poorly
ventilated locations or areas where exhaust fans may
cause an insufficient supply of oxygen. Sufficient
combustion can only be obtained when there is a
sufficient supply of oxygen available for the amount
of fuel being burned. If it is necessary to install a
machine in a poorly ventilated area, outside fresh
air may have to be piped to the burner and a fan
installed to bring air into the machine.
Avoid small locations or areas near exhaust fans.