6189N 6)& :L)L 0RGXOH 9 Module manual
6189N 6)& :L)L 0RGXOH 9 Customer Approval : Company Title Signature Date Fn-Link
6189N-SFC Revision History Version Date Revision Content Draft Approved 1.0 2019/01/10 New version Lzm Lxy 1.1 2019/04/10 Update thickness dimension Lxy Szs 1.2 2019/08/06 Update packing information Lxy Szs 1.
6189N-SFC CONTENTS 1 Overview....................................................................................................................................1 1.1 Introduction......................................................................................................................... 1 1.2 Features.............................................................................................................................. 1 1.3 General Specification..........................................
6189N 1 Overview 1.1 Introduction 6189N-SFC is a highly integrated and excellent performance Wireless LAN (WLAN) SDIO network interface device. High-speed wireless connection up to 150 Mbps. It can be easily manufactured on SMT process. This WLAN Module design is based on Realtek RTL8189FTV-VC-CG. It is a highly integrated single-chip Wireless LAN (WLAN) SDIO network interface controller complying with the 802.11n specification. It combines a MAC, a 1T1R capable baseband, and RF in a single chip.
189N 6)& 1.3 General Specification Model Name 6189N 6)& Product Description S:L)L 0RGXOH 9 Dimension L x W x T: 23 x 21 x 4.8 (typical) mm Wi-Fi Interface Support SDIO Operating temperature 0°C to 70°C Storage temperature -55°C to +125°C 1.4 Recommended Operating Rating Min. Typ. Max. Unit 0 25 70 VBAT 3.0 3.3 3.6 deg.C V VDDIO 1.7 1.8 or 3.3 3.6 V Operating Temperature ※1.5 EEPROM Information WI-FI Vendor ID 024C Product ID F179 2 General Specification 2.
6189N-SFC PHY Data rates Wi-Fi: 802.11b: 11, 5.5, 2, 1 Mbps 802.11g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11n: up to 150Mbps Transmit Output Power Wi-Fi: 802.11b@11Mbps 15±2dBm 802.11g@54Mbps 14±2dBm 802.11n@65Mbps 14±2dBm Other rate power control by power by rate. EVM 802.11b /11Mbps: EVM≦-9dB 802.11g /54Mbps: EVM≦-25dB 802.11n /65Mbps: EVM≦-28dB Receiver Sensitivity (HT20) 802.11b@8% PER 11Mbps< -82dBm 802.11g@10% PER 54Mbps< -71dBm 802.11n@10% PER MCS 7 <-67dBm Operating Channel Wi-Fi 2.
6189N 6)& GND 1 19 GND GND 2 18 GND GND 3 17 GND SD_D3 13 14 15 16 GND SD_D2 12 SD_D1 11 SD_D0 10 SD_CLK 9 SD_CMD 8 WL_WAKE_HOST NC 7 CHIP_EN VBAT 6 GND 5 VDDIO 4 3.2 Pin Definition F NO. Name Type 1 GND Ground connections 2 GND Ground connections 3 GND Ground connections 4 VBAT 5 NC 6 VDDIO 7 GND 8 CHIP_EN I Wi-Fi enable pin, default pull high 3.3V 9 WL_WAKE_HOST I/O WLAN to wake-up HOST 1.8V ~ 3.3V 10 SD_D2 I/O SDIO Data line 2 1.
6189N-SFC 14 SD_D0 I/O SDIO Data line 0 1.8V ~ 3.3V 15 SD_D1 I/O SDIO Data line 1 1.8V ~ 3.3V 16 GND Ground connections 17 GND Ground connections 18 GND Ground connections 19 GND Ground connections 4.
6189N-SFC 4.3 Module Physical Dimensions 23 2.65 1 4.15 5.65 11.5 0.7 0.35 1.15 2.65 4.15 5.65 7.15 8.65 10.
6189N-SFC 4.4 Layout Reference (unit: mm ) 23 2.65 1 4.15 5.65 11.75 0.7 4.15 5.65 7.15 8.65 10.75 F 0.35 1.15 2.
6189N-SFC 6 Host Interface Timing Diagram 6.1 SDIO Pin Description The module supports SDIO version 2.0 for all 1.8V 4-bit UHSI speeds: SDR12(25 Mbps), and SDR25(50Mbps) in addition to the 3.3V default speed(25MHz) and high speed (50 MHz). It has the ability to stop the SDIO clock and map the interrupt signal into a GPIO pin. This ‘out-of-band’ interrupt signal notifies the host when the WLAN device wants to turn on the SDIO interface.
6189N-SFC 6.2 SDIO Default Mode Timing Diagram 6.3 SDIO Power-on sequence Symbol Min Typical Max Unit T33ramp 0.2 - No Limit ms Toff 250 500 1000 ms T33ramp 0.2 0.5 2.5 ms T12ramp 0.1 0.5 1.
6189N-SFC 7 Reference Design Note: 1. chip_EN could not use for module power off, please switch the 3.3V power for module on/off. 2.please keep the antenna on no metal area.
6189N-SFC 8 Ordering Information Part No. Description FG6189NSFC-00 RTL8189FTV-VC-CG b/g/n, Wi-Fi, 1T1R, 23X21mm, SDIO, PCB V1.0 with antenna 9 The Key Material List Main Shielding cover Main Crystal Main ESD Main Chipset 6189N-SFC V1.0 Shielding cover no insulation 14.79x10.72-full height of 1.4 copper, no positioning pin 26mhz 3225 ±10ppm, 10.5pF, E3SB26E00002SE10C0BB (HOSONIC) 0402 5.5V 0.1pF GESD1005H5R5CR10GPT(Sunlord) RTL8189FTV-VC-CG 10 Environmental Requirements 10.
10.2 Patch Wi-Fi modules installed before the notice 6189N-SFC Wi-Fi module installed note: 1. Please press 1 : 1 and then expand outward proportion to 0.7 mm, 0.12 mm thickness When open a stencil. 2. Take and use the WIFI module, please insure the electrostatic protective measures. 3. Reflow soldering temperature should be according to the customer the main size of the products, such as the temperature set at 250 + 5 ℃ for the MID motherboard.
6189N-SFC 11 Package 11.1 Reel A roll of 350pcs 11.2 Packaging Detail the take-up package Using self-adhesive tape Size of black tape:44mm*12.48m the cover tape :37.5mm*12.
6189N-SFC NY bag size:420mm*450mm The packing case size:335*255*360mm F size ：335*335*55mm
RF Exposure Information and Statement This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 5、 FCC and IC Statement This device complies with part 15 of the FCC rules and RSS-247 of Industry Canada.
Instructions to the OEM/Integrator: This module has been granted modular approval for mobile applications. OEM integrators for host products may use the module in their final products without additional FCC/ISED (Innovation, Science and Economic Development Canada) certification if they meet the following conditions. Otherwise, Additional FCC/IC approvals must be obtained. The OEM must comply with the FCC labeling requirements.
