Manual tauron
Content 1. Features 3 2. Package content 3 3. The case at a glance 4 4. Installation notes 8 5. Rebuilding the HDD cages 9 6. Installation of a mainboard 11 7. Installation of a PSU 14 8. Installation of a HDD 15 9. Installation of an optical device 17 10. Installation of a 3.5" device 19 11. Installation of an add-on card 21 12. The pre-installed fans / using the fan control 21 13.
1. Features • • • • • • • • • • • • • ATX case 2x 5.25" drive bays (external) 1x 5.25" or 3.5" drive bays (external) 7x 2.5" or 3.5" bays with removable mounting trays for HDDs (internal) Top I/O: 2x USB3.0, 2x USB2.
3. The case at a glance Front panel a B C A – 5.25" drive bays B – 3.
Side panel (opened/left) a a b B C E D A – Mainboard mounting panel a – Installation opening for CPU coolers b – Cable feedthrough B – 5.25" drive bays C – 3.
Side panel (opened/right) E a B a C D b A B C D E – – – – – 5.25" drive bays 3.
Top panel a B e a c B – Top I/O: a – 2x USB3.0 b – 2x audio c – Reset button d – 2x USB2.
The internal I/O connectors a B C D a b E F a b c d e A – Audio connectors for: a – HD Audio b – AC’97 B – USB2.0 connector C – 2x USB3.0 connectors D – Fan control connector E – Front-I/O power connector F – Connectors for: a – Power Switch b – Power LED – c – Power-LED + d – HDD-LED e – Reset-Switch 4. Installation notes 1. For further information on how to install the PC components, please also refer to their respective instructions. 2.
5. Rearranging the HDD cages The HDD cages of the case may be re-arranged, so that VGA cards up to 42 cm can be installed.
In order to remove the HDD cages, proceed as follows: 1. Unscrew the thumb screws on the back side of the case and remove both side panels. 2. Lift the attachment lever of the respective HDD cage (fig. 1) and drag the cage out of its fitting (fig. 1b). fig. 1a fig. 1b 3. Slide the HDD cage into the respective bottom fitting of the case until the attachment lever locks (fig. 2a and b). fig.
8. Installation of a HDD 1. Take a mounting frame from one of the HDD cages (fig. 9). Fig. 9 Mounting frame 2. Place an HDD into the mounting frame (connectors pointing backwards / fig. 10a and b). Fig. 10a Fig.
3. Attach the HDD to the mounting frame from below (fig. 11a and b). Fig. 11a Fig. 11b 4. Slide the mounting frame into the HDD cage until it locks (fig. 12). Fig. 12 5. Connect the HDD to the PSU and the mainboard.
9. Installation of an optical device 1. Remove the case’s front panel by gently pulling it towards you (fig. 13). Fig. 13 2. Dismantle the 5.25" front bezel from the mounting bay by removing it from the front panel (fig. 14). Fig.
3. Place the front panel back onto the case. 4. Slide the optical drive into the case’s drive bay (fig. 15). Fig. 15 5. Attach the optical device to the case from both sides using the quick fasteners (fig. 16). Fig. 16 Note: If you intend to transport the case, we recommend that you screw-in the built-in devices (additionally). 6. Connect the optical drive to the power supply and the mainboard.
10. Installation of a 3.5" device 1. Remove the case’s front panel by gently pulling it towards you. 2. Dismantle the 3.5" front bezel by removing it from the front panel (fig. 17). Fig. 17 3. Unlock the quick fasteners, which attach the mounting frame for 3.5” devices inside the case (fig. 18a) and remove the mounting frame from the case (fig. 18b). Fig. 18a Fig. 18b (Carefully remove an optionally present metal bezel covering the 3.5" drive bay by using a gripper.
4. Place the 3.5" device into the mounting frame for 3.5" devices and attach the device to the frame from both sides (fig. 19). Fig. 19 5. Slide the mounting frame with the installed 3.5" device into the case’s mounting bay (fig. 20a) and lock it from both sides using the quick fasteners (fig. 20b). Fig. 20a Fig. 20b 6. Connect the 3.5" device to the power supply and the mainboard. 7. Replace the front bezel to the case.
11. Installation of an add-on card 1. Remove the anchor screw of the slot bezel and take it from the case. 2. Insert the add-on card into the respective slot of the mainboard and attach it to the case using the anchor screw (fig. 21). Fig. 21 3. Close the case. 12.
Fan connector of the fan control Sliders of the fan control 13. Installation of an additional bottom panel fan / optimized airflow The case provides the opportunity to install an additional 120 or 140 mm fan into the bottom panel. Therefore proceed as follows: 1. Remove the bottom fitting for the HDD cages by loosening its four mounting screws und removing the fitting from the case (fig. 23). Fig.
2. Place the fan against the respective bracket from the inside of the case. 3. Screw the fan to the attachment from the outside. 4. Connect the fan to the mainboard or the PSU. Notes: When installing fans, make sure that (cool) air is taken in on the front/bottom of the case and blown out on its rear side/top. The PC components with the highest heat development should be placed directly within the airflow.
