User Manual
19
Recording With The Timer (Continued)
REC TIMER PROGRAM
10:20AM OCT.15(FRI)
MODE CH START STOP
1 DAILY 82 4:30
PM
6:00
PM
SP
2 MON-FRI 123 10:00
AM
1
1:30
AM
EP
3 15(SAT) 56 11:00
AM
1:20
PM
SP
4
5
COMPLETE NEXT CHANGE DELETE
SELECT + / — : SET SET
PREVIOUS RETURN : QUIT MENU
REC TIMER PROGRAM
10:20AM OCT.15(FRI)
MODE CH START STOP
1 DAILY 82 4:30
PM
6:00
PM
SP
2 MON-FRI 123 10:00
AM
1
1:30
AM
EP
3 15(SAT) 56 11:00
AM
1:20
PM
SP
4
5
COMPLETE NEXT CHANGE DELETE
SELECT + / — : SET SET
PREVIOUS RETURN : QUIT MENU
REC TIMER PROGRAM
10:20AM OCT.15(FRI)
MODE CH START STOP
1 DAILY 82 4:30
PM
6:00
PM
SP
2 MON-FRI 123 10:00
AM
1
1:30
AM
EP
3 15(SAT) 56 11:00
AM
1:20
PM
SP
4
5
COMPLETE NEXT CHANGE DELETE
SELECT PROGRAM TO CHANGE
SELECT + / — : SET SET
PREVIOUS RETURN : QUIT MENU
REC TIMER PROGRAM
10:20AM OCT.15(FRI)
MODE CH START STOP
1 DAILY 82 4:30
PM
6:00
PM
SP
2 MON-FRI 123 10:00
AM
1
1:30
AM
EP
3 15(SAT) 56 11:00
AM
1:20
PM
SP
4
5
COMPLETE NEXT CHANGE DELETE
SELECT PROGRAM TO DELETE
SELECT + / — : SET SET
PREVIOUS RETURN : QUIT MENU
PROGRAM TIMER 1
PROGRAM TIMER 2
7:00 8:00 8:30 10:00
7:00 8:30 10:00
PROGRAM TIMER 1
Start
Recording
Start
Recording
End
Recording
End
Recording
Start
Recording
Start
Recording
End
Recording
End
Recording
PROGRAM TIMER 2
L Notes on the Timer Recording
• To correct any erroneous data entry made during program
timer setting work:
(1) Press the RETURN button on the Remote Control to
return to the item you wish to change.
(2) Press the + or – button on the Remote Control to reset
the data.
(3) To advance operation, press the SET button.
• If the video cassette runs out of tape before recording all
the programs, the VCR will stop, eject the cassette and
shut off automatically.
• If you keep disconnected the power cord, the program
timer will be cancelled.
• If “complete” is selected to enter the TIMER Standby mode
when there is no cassette inserted, the PROGRAM TIMER
indicator flashes for 3 seconds and the message “NO
TAPE” appears indicating that timer recording is not
possible.
• If “complete” is selected to enter the TIMER Standby mode
while a cassette with the erasure protection tab removed
is inserted, the PROGRAM TIMER indicator flashes and
the cassette is ejected.
• To stop timer recording, press the STOP button.
• If no buttons are pressed within 3 minutes while setting a
program, the set automatically returns to the normal
viewing mode.
• A program cannot be set unless all the recording input
data is set.
• During program timer setting (with the Program Timer
indicator ON), the video set remains inoperative. To use
the video set, press the TIMER ON/OFF button on the
Remote Control to turn off the Program Timer indicator.
After use, load the cassette tape into the video set, press
the TIMER ON/OFF button and check that the Program
Timer indicator lights up.
• Be certain that the correct TV signal mode (AIR/CABLE)
is selected before you enter the Timer Standby mode.
Otherwise, the VCR may not record the desired TV
channel.
• If two Pre-Recording Timers overlap, the End Recording
Time of the PROGRAM TIMER 1 will have priority over
the Start Recording Time of the PROGRAM TIMER 2.
Example:
Pre-Recording Timer’s Interval
Actual Recording Timer’s Interval
L To confirm the program content, press the CONFIRM
button on the Remote Control.
L To add to the program content:
(1) Press the CONFIRM
button on the Remote
Control.
(2) Press the + or – button
to select “NEXT”, then
press the SET button.
(3) To add a program, follow
the steps (3) through (10)
of “Setting The Program
Timer”.
L To change the program content:
(1) Press the CONFIRM
button on the Remote
Control.
(2) Press the + or – button
to select “CHANGE”, then
press the SET button.
(3) Press the + or – button
to select the program you
wish to correct, then press
the SET button.
To reset the program,
follow the steps (3)
through (10) of “Setting
The Program Timer”.
L To delete the program content:
(1) Press the CONFIRM
button on the Remote
Control.
(2) Press the + or – button
to select “DELETE”, then
press the SET button.
(3) Press the + or – button
to select the program you
wish to delete, then press
the SET button.
(4) Press the CONFIRM
button to return to the
normal screen.
Note:
• During the Program Timer Setting (with the Program Timer
indicator ON), it is impossible to change or delete the
program content. To perform these operations, press the
TIMER ON/OFF button on the Remote Control and turn
off the Program Timer indicator.
16-19 13VT-CR10[E].pm65e 15/5/01, 7:25 pm19