AF-S155NX N
Please read ALL instructions before installing. Two people are recommended to install this product. If a new electrical outlet WINDOW SASH SEAL is required, have the outlet installed by a qualified electrician before installing unit. See#5 in Preliminary Instructions SAFETY LOCK AND 3/4" LONG HEX HEAD SCREW following. Preliminary instructions Do the following before starting to install unit. See illustrations below. Check dimensions of your unit to determine model type: Unit Height: Unit Width: Min.
4. CHECK FOR ANYTHING THAT COULD BLOCK AIRFLOW - check area outside of window for things such as shrubs, trees, or awnings. Inside, be sure furniture, drapes, or blinds will not stop proper air flow. 5. Check the available electrical service - power supply must be the same as that shown on the unit serial nameplate. Power cord is 48"long. Be sure you have an outlet near. All models have a 3-prong service plug to provide proper service and safe positive grouding. Do not change plug in any way.
2 1 Install Top Angle and Side Bracket 1. Attach foam gasket to top angle above holes as shown in FIG. 6. Remove Chassis 1. Pull down front panel and remove filter. (See FIG. 1). 2. Lift front upwards and place to one side. FIG. 1 FIG. 2 3. Locate the four front screws and remove. These screws will be needed to re-install the front later. (See FIG.2) 4. Pry away front from cabinet sides as per photo (see FIG.3) 5. Gently lift front off unit and place to one side (See FIG.4). FIG. 3 FIG. 6 FIG. 4 2.
3. Insert top and bottom legs of window filler panel frame into channel in the to angle and bottom rail. Do both sides. 4. Insert washer head locking screws (2) into holes in top leg of filler panel frame (see Step 6). Do not totally tighten. Allow leg to slide freely. Screws will be tightened after Section 6. 4 5 Install Support Bracket 1. Hold each support bracket flush against outside of sill, and tight to bottom of cabinet as shown below. Mark brackets at top level of sill, and remove.
6 Extend Window Filler Panels 1. Carefully raise window to expose filler panel locking screws. Loosen screws so filler panels slide easily. 8 1. Lift air conditioner and carefully slide into cabinet leaving 6" protruding. 2. LOCKING SCREWS 2. Extend panels to fill window opening completely. Tighten locking screws on top. 3. Close window behind top angle. 7 Install Window Lock and Sash Seal 1. Trim sash seal to fit window width. Insert into space between upper and lower sashes. WINDOW SASH SEAL 2.
TO CHANGE TEMPERATURE SETTING: YOU WILL SEE: DO THIS: PRESS TO RAISE PRESS TO LOWER Note: Tap or hold either up ( ▲ ) or down ( ) button until the desired temperature is seen on the display. This temperature will be automatically maintained anywhere between 60oF (16oC) and 90oF (32oC) for cooling mode. If you want the display to read the actual room temperature. See "To Operate on Fan " section on Page 13.
TO OPERATE ON FAN: YOU WILL SEE: LIGHT On DO THIS: PRESS MODE BUTTON CHOOSE FAN Note: Use this function only when cooling is not desired, such as for room air circulation or to exhaust stale air. (Remember to open the vent during this function, but keep it closed during cooling for maximum cooling efficiency.) You can choose any fan speed you prefer. (Except "Auto Cool"). During this function, the display will show the actual room temperature, not the set temperature as in the cooling mode.
FAULT CODES TO TURN UNIT OFF: DO THIS: PRESS POWER ON/OFF If the display reads "ES" or "AS", a sensor has failed. Contact your Authorized SHARP Service Center. Fresh Air Vent Control The Fresh Air Vent allows the air conditioner to: 1. Recirculate inside air - Vent Closed (see Fig. 1) 2. Draw fresh air into the room - Vent Open (see Fig. 2) 3. Exchange air from the room and draws fresh air into the room - Vent and Exhaust Open (see Fig. 3) Fig. 1 (OFF) Fig. 2 (FRESH AIR) Fig.
66129901273
