Specifications

MX-3610N TROUBLESHOOTING 6 – 47
(7) LCC
(8) Inner finisher
(9) Saddle finisher
JAM code JAM content
JAM detection method
JAM detection start trigger JAM judgment condition
LCC Side LCC paper feed JAM (LPFD not-reached) LPFC ON (paper feed start) LPFD does not turn ON within the specified time.
LPFD_SL LPFD remaining JAM (Side LCC feed paper) LPFD ON LPFD does not turn OFF within the specified time.
JAM code JAM content
JAM detection method
Basic distance
(A) [mm]
JAM margin
distance (B)
[mm]
JAM detection
distance (A+B)
[mm]
JAM detection start
trigger
JAM judgment condition
FPPD1_N Finisher inlet port
not-reached JAM
Machine paper exit
command reception
FPPD1 does not turn ON within the
specified time.
134.602 [mm] 400 [mm] 534.602 [mm]
FPPD1_S Finisher inlet port
remaining JAM
(When Long-size paper
support OFF)
FPPD1 ON FPPD1 does not turn OFF within
the specified time.
464.803 [mm] 50 [mm] 514.803 [mm]
Finisher inlet port
remaining JAM
(When Long-size paper
support ON)
FPPD1 ON FPPD1 does not turn OFF within
the specified time.
1207.803 [mm] 50 [mm] 1257.803 [mm]
FPDD_S Bundle exit remaining
JAM
Driving the bundle exit
roller is started.
FSTPD does not turn OFF within
the specified time.
133.1 [mm] 13.66 [mm] 146.76 [mm]
FIN_TIME Finisher paper early
reaching JAM
FPPD1 ON by the
prior paper detection
FPPD1 of the next paper turns ON
at the timing earlier than the
specified paper interval.
Specified paper
interval time
30 [mm] (Paper interval
time) - (Paper
transport time
of 30 [mm])
[msec]
FSTPD_S Finisher paper exit
remaining JAM
Driving the paper exit
roller in the straight
mode is started.
FSTPD does not turn OFF within
the specified time.
96.76 [mm] 50 [mm] 146.76 [mm]
FSTPLJ Staple JAM FSHPS OFF after
FSM ON
FSHPS does not turn ON within the
specified time.
350 [msec] 250 [msec] 600 [msec]
JAM code JAM content
JAM detection method
Basic distance
(A) [mm]
JAM margin
distance (B)
[mm]
JAM detection
distance (A+B)
[mm]
JAM detection start
trigger
JAM judgment condition
PDPPD1_N Interface inlet port not-
reached JAM
Machine paper exit
command reception
PDPPD1 does not turn ON within
the specified time.
79.6 [mm] 238.8 [mm] 318.4 [mm]
PDPPD1_S Interface inlet port
remaining JAM
PDPPD1 ON PDPPD1 does not turn OFF within
the specified time.
(Paper length +
11.3) [mm]
(Paper length +
11.3) [mm]
(Paper length +
11.3) x 2 [mm]
PDPPD2_N Interface outlet port not-
reached JAM
PDPPD1 ON PDPPD2 does not turn ON within
the specified time.
318.7 [mm] 318.7 [mm] 637.4 [mm]
PDPPD2_S Interface outlet port
remaining JAM
PDPPD2 ON PDPPD2 does not turn OFF within
the specified time.
(Paper length +
11.3) [mm]
(Paper length +
11.3) [mm]
(Paper length +
11.3) x 2 [mm]
FPPD1_N Finisher inlet port not-
reached JAM
PDPPD2 ON FPPD1 does not turn ON within the
specified time.
180.3 [mm] 180.3 [mm] 360.6 [mm]
FPPD1_S Finisher inlet port
remaining JAM
Paper reaches the
finisher speed change
position.
FPPD1 does not turn OFF within
the specified time.
108.4 [mm] 216.8 [mm] 325.2 [mm]
FPPD2_N Saddle section not-
reached JAM
The lead edge of
paper reaches the
position of 20mm past
the saddle No. 1
transport roller.
FPPD2 does not turn ON within the
specified time.
110.4 [mm] 110.4 [mm] 220.8 [mm]
FPPD2_S Saddle section
remaining JAM
The rear edge of
paper reaches the
position of 20mm past
the process roller.
FPPD2 does not turn OFF within
the specified time.
220.4 [mm] 220.4 [mm] 440.8 [mm]
FPDD_S Bundle exit remaining
JAM
Gripper discharging is
started.
FATPD does not turn OFF within
the specified time.
437 [msec] 437 [msec] 874 [msec]
Gripper discharging is
completed.
FPDD does not turn ON when
gripper discharging is completed.
FPDD OFF