Specifications

MX-3610N SIMULATION 5 – 84
44-61
Purpose
Adjustment
Function (Purpose)
Used to adjust the color image density sen-
sor. (The adjustment is made according to
the input of SIM44-13 to set the target value
of the color sensor gain adjustment.)
Section
Operation/Procedure
1) Select an adjustment target item with scroll key.
2) Enter the set value with 10-key.
3) Press [OK] key. (The set value is saved.)
44-62
Purpose
Setup/Adjustment
Function (Purpose)
Used to set the process control execution
conditions.
Section
Process
Operation/Procedure
This simulation allows collective change in the set contents of
SIM44-4 and SIM44-28.
A suitable one is selected among a number of options depending
on the condition.
1) Select an item to be set.
To change the image density in the high density area, select
PROCON TARGET.
To change the frequency of the process control operations,
select PROCON MODE.
(When PROCON TARGET is selected.)
2A) Select the density level.
(When PROCON MODE is selected.)
2B) Select the execution frequency of the process control.
3) Press [EXECUTE] key.
4) Press [YES] key.
This simulation may not function with some firmware versions.
In such a case, the firmware must be upgraded to the latest ver-
sion.
46
46-1
Purpose
Adjustment (Color copy mode)
Function (Purpose)
Used to adjust the copy density in the copy
mode.
Section
Operation/Procedure
1) Select an adjustment target item with scroll key on the touch
panel.
2) Enter the set value with 10-key.
* When the key is pressed, the setting value of each
item can be changed with 1up (1down) collectively.
3) Press [OK] key. (The set value is saved.)
To adjust the copy density in the low density area, select the "LOW"
mode and change the adjustment value. To adjust the copy density
in the high density area, select the "HIGH" mode and change the
adjustment value.
When the adjustment value is increased, the copy density is
increased. When the adjustment value is decreased, the copy den-
sity is decreased.
18cpm/20cpm/23cpm/31cpm(G) machine
Item/Display Content
Setting
range
Default
value
A PCS_CL CARB OUT Calibration plate sensor
value
1 - 255 108
B PCS_CL LED ADJ Color sensor light
emitting quantity
adjustment value
1 - 255 21
Display/Item Content
PROCON
TARGET
CL ID DOWN The densities of C, M, and Y decrease.
(The C/M/Y high density process control
target values decrease.)
CL ID UP The densities of C, M, and Y increase.
(The C/M/Y high density process control
target values increase.)
BK ID DOWN The density of K decreases. (The high
density process control target value
decreases.)
BK ID UP The density of K increases. (The high
density process control target value
increases.)
ALL ID DOWN The densities of C, M, Y and K decrease.
(The C/M/Y/K high density process
control target values decrease.)
ALL ID UP The densities of C, M, Y and K increase.
(The C/M/Y/K high density process
control target values increase.)
NORMAL The standard density of C, M, Y and K.
(The C/M/Y/K high density process
control target values are the standard
values.)
PROCON
MODE
HIGH QUALITY1 The execution frequency of the process
control is high. (It is set when the color
image quality is given priority.)
HIGH QUALITY2 The execution frequency of the process
control is highest. (It is set when the color
image quality is given priority.)
PRINT
PERFORMANCE
The execution frequency of the process
control is low. (It is set when the job
speed is given priority.)
BW MODE The process control is executed in the
normal frequency. (It is set when there
are little color jobs and many
monochrome jobs.)
NORMAL The process control is executed in the
normal frequency.
Item/Display Content
Setting
range
Default
value
A AUTO Auto LOW 1 - 99 50
HIGH 1 - 99 50
B TEXT Text LOW 1 - 99 50
HIGH 1 - 99 50
C TEXT/PRINTED
PHOTO
Text/Printed
Photo
LOW 1 - 99 50
HIGH 1 - 99 50
D TEXT/PHOTO Text/Photograph LOW 1 - 99 50
HIGH 1 - 99 50
E PRINTED PHOTO Printed Photo LOW 1 - 99 50
HIGH 1 - 99 50
F PHOTOGRAPH Photograph LOW 1 - 99 50
HIGH 1 - 99 50
Display/Item Content