Specifications

MX-3610N SIMULATION 5 – 109
48-6
Purpose
Adjustment
Function (Purpose)
Used to adjust the rotation speed of each
motor.
Section
Operation/Procedure
1) Select an adjustment target mode with [COLOR] [MONO]
[HEAVY] keys on the touch panel.
2) Select a target adjustment item with scroll key on the touch
panel.
3) Enter the set value with 10-key.
4) Press [OK] key.
The set value is saved.
When the adjustment value is increased, the speed is increased,
and vice versa. A change of 1 in the adjustment value corresponds
to a change of about 0.1% in the speed.
18cpm/20cpm/23cpm/26cpm/31cpm machine
* Common items for color, monochrome, and heavy paper
** Common items for color and monochrome
The greater the correction value is, the higher the speed is, and
vice versa. Change by ±1 corresponds to 0.1%.
*1: In the case of 20cpm machine
*2: In the case of 23cpm machine
36cpm machine
Default value of FSM
This must be set to the default unless any change is specially
required.
When the adjustment value is set to a value greatly different from
the default value, a jam, paper wrinkle, or image quality trouble
may occur.
49
49-1
Purpose
Function (Purpose) Used to perform the firmware update.
Section
Operation/Procedure
1) Save the firmware to the USB memory.
2) Insert the USB memory into the main unit. (Use USB I/F of the
operation panel section.)
3) Select a target firmware file for update with the touch panel.
4) Select a target firmware.
Press [ALL] key to select all the Firmware collectively.
5) Press [EXECUTE] key.
6) Press [YES] key.
The selected firmware is updated.
When the operation is normally completed, "COMPLETE" is
displayed. When terminated abnormally, "ERROR" is dis-
played.
18cpm/20cpm/23cpm/31cpm(G) machine
Mode
Select
Item/Display Content
Setting
range
Default
value
COLOR A RRM Registration motor
correction value
(23cpm machine only)
1 - 99 51
MONO
HEAVY
COLOR B DVM_K Developing K motor
correction value
1 - 99 45
MONO
HEAVY
COLOR** C FSM Fusing motor
correction value
1 - 99 38*
1
44*
2
HEAVY 41
COLOR D DVM_CL Developing CL motor
correction value
1 - 99 45
HEAVY
COLOR* E PFM Paper transport motor
correction value
(23cpm machine only)
1 - 99 48
COLOR* F POM Paper exit motor
correction value
1 - 99 50
HEAVY E FUSER
SETTING
Fusing speed select
timing
(23 cpm machine only)
1 - 99 60
HEAVY F RRM
START
Registration motor
speed increasing start
timing
0 - 255 109
HEAVY G RRM
END
Registration motor
speed increasing end
timing
0 - 255 210
Mode Item/Display Content
Setting
range
Default
value
COLOR A RRM Registration motor
correction value
1 - 99 51
MONO
HEAVY
COLOR B BTM Belt motor correction
value
1 - 99 47
MONO
HEAVY
COLOR C DVM_K Developing K motor
correction value
1 - 99 45
MONO
HEAVY
COLOR** D FSM Fusing motor
correction value
1 - 99 Refer
to the
list
below.
HEAVY
COLOR E DVM_CL Developing CL motor
correction value
1 - 99 45
HEAVY
COLOR* F PFM Paper transport motor
correction value
1 - 99 48
COLOR* G POM Paper exit motor
correction value
1 - 99 50
HEAVY F FUSER
SETTING
Fusing speed select
timing
1 - 99 60
HEAVY G RRM
START
RPM acceleration start
timing
0 - 255 109
HEAVY H RRM
END
RPM acceleration end
timing
0 - 255 210
Item
Default value
26cpm/31cpm machine 36cpm machine
Group
A
Group
A
Group
B
Group
C
Group
B
Group
C
D444444444444
Group Destination
Group A JAPAN AB_B CHINA
Group B U. S. A CANADA INCH
Group C EUROPE U. K AUS. AB_A
Item/Display Content
Error display in
case of abnormality
CONFIG Configuration data CONF
ICU (MAIN) ICU Main section ICUM
ICU (BOOTM) ICU Boot section main ICUBM
ICU (BOOTCN) ICU Boot section CN ICUCN
ICU (SUB) ICU Sub section (ARM9) ICUS
LANGUAGE Language support data
program
LANG
GRAPHIC Graphic data for L-LCD GRAPH
SLIST SLIST data for L-LCD SLIST
PCL (BOOT) PCL Boot section PCLB
PCL (MAIN) PCL Main section PCLM
Mode Item/Display Content
Setting
range
Default
value