MODEL AL-1670 DIGITAL LASER COPIER/PRINTER COPIER OPERATION MANUAL • GETTING STARTED Page 2 • MAKING COPIES 16 • SPECIAL FEATURES 30 • STATUS INDICATORS 39 • GENERAL INFORMATION 49
FOR YOUR PROTECTION... To aid in reporting this compact copier in case of loss or theft, please record below the serial number located on the back of the unit. We also suggest you record all the information listed and retain for future reference.
CONTENTS INTRODUCTION This copier can be used as a laser printer. However, this manual describes only the copier features. For description of the printer features, see the printer manual. GETTING STARTED ● ● ● ● ● ● ● ● MAKING COPIES In this manual, the following icons are used to provide the user with information pertinent to the use of the copier. ● ● ● ● ● ● ● SPECIAL FEATURES ● ● ● ● ● ● ● XY ZOOM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B/W REVERSE . . . . . .
CAUTIONS GETTING STARTED Follow the cautions below when using this copier. Cautions ● The fusing area is hot. Exercise care in this area when removing misfed paper. ● Do not look directly at the light source. Doing so may damage your eyes. ● The socket-outlet shall be installed near the equipment and shall be easily accessible. ● Place the copier on a firm, level surface. ● Do not install the copier in a humid or dusty location.
MAIN FEATURES ● GETTING STARTED High-speed laser copying ● First-copy time is only 7.2 seconds (except in a power save mode or immediately after power on). Copying speed is 16 copies/min., which adapts to business use, allowing improvement of working efficiency. High-quality digital image ● High-quality copying at 600 dpi is performed. ● In addition to the automatic exposure mode, the manual exposure can be adjusted in five steps.
PART NAMES AND FUNCTIONS GETTING STARTED Overall layout e q o Part names and functions !1 w y e !0 !2 !3 u r t !4 i q Document feeder cover Open to make copies from the original table. i Paper tray Each tray holds 250 sheets of copy paper. w Original table All originals which cannot be copied from the SPF must be copied here. o Side cover Open to remove misfeeds and to service the copier. e Handles Use to move the copier. r Power switch Press to turn copier power on and off.
PART NAMES AND FUNCTIONS Single pass feeder (SPF) !5 !6 !7 !8 GETTING STARTED @6 !9 @1 Part names and functions @7 @0 @2 @3 @4 @5 !5 SPF exit area Finished originals are output here. @3 TD cartridge Contains toner. !6 Document feeder tray Holds up to 30 originals. @4 Roller rotating knob Turn to remove misfed paper. !7 Original guides Adjust to the size of the originals. @5 Fusing unit release levers Lower to remove misfed paper. !8 Feeding roller cover Open to remove misfed originals.
PART NAMES AND FUNCTIONS Operation panel q w e r ty ui GETTING STARTED Part names and functions !4 !5 !6 !7 !8 !9 @0 @1 @2 @3 @4 q Operation panel and keys for printer features See the printer manual. !0 PAPER SIZE ENTER ( ) key (p. 15) Use to set the paper size in a tray. / / ) key w AUTO/MANUAL/PHOTO ( and indicators (p. 16) Use to sequentially select the exposure modes: AUTO, MANUAL ( ), or PHOTO ( ).
PART NAMES AND FUNCTIONS o !0 t !1 !2 !3 GETTING STARTED @7 @8 @9 #0 Part names and functions @6 #1 @0 SORT/GROUP ( / ) key and indicators (p. 25) Press to select the sort or group mode. @1 ORIGINAL DATA ( ) indicator Blinks when the memory becomes full of scanned original image data. @2 Light ( ) and dark ( ) keys and indicators (p. 17) Use to adjust the MANUAL ( ) or PHOTO ( ) exposure level. ) key and indicator (p. 20) @3 AUTO IMAGE ( Press for automatic copy ratio selection.
COPIER INSTALLATION GETTING STARTED Improper installation may damage the copier. Please note the following during initial installation and whenever the copier is moved. If the copier is moved from a cool place to a warm place, condensation may form inside the copier. Operation in this condition will cause poor copy quality and malfunctions. Leave the copier at room temperature for at least 2 hours before use.
CAUTIONS ON HANDLING GETTING STARTED Be careful in handling the copier as follows to maintain the performance of this copier. Do not drop the copier, subject it to shock or strike it against any object. Cautions on handling Do not expose the drum cartridge to direct sunlight. Doing so will damage the surface (green portion) of the drum cartridge, causing poor copy quality. Store spare supplies such as drum cartridges and TD cartridges in a dark place without removing from the package before use.
CHECKING PACKED COMPONENTS AND ACCESSORIES GETTING STARTED Open the carton and check to ensure that the following components and accessories are included. TD cartridge Checking packed components and accessories Copier operation manual Printer operation manual CD-ROM (Printer driver) Power cord Copier Drum cartridge (installed in copier) ● If anything is not included or is damaged, contact our Technical Assistance Department at 1(630)378-3590. ● Save the carton and packing materials.
SET-UP GETTING STARTED Set-up 1 2 Remove all pieces of tape, then open the document feeder cover and remove the protective material. Use a coin (or other suitable object) to remove the screw. Store the screw in the paper tray as described in step 6 because it must be used if the copier has to be moved. (p. 60) 3 Install the TD cartridge. ● For installation of the TD cartridge, see steps 1 and 2 and steps 4 to 7 of TD CARTRIDGE REPLACEMENT on pages 39 and 40.
SET-UP GETTING STARTED Pressure plate lock 6 Store the pressure plate lock which has been removed in step 5 and the screw which has been removed in step 2 in the front of the paper tray. ● To store the pressure plate lock, rotate the lock to fix it on the relevant location. ● Follow steps 4 to 6 for both the upper and lower trays except for storage of the screw. Set-up Screw 7 Ensure that the power switch of the copier is in the OFF position. Plug the power cord into the nearest outlet.
LOADING COPY PAPER GETTING STARTED To save space, this copier has been designed with two adjustable front-loading trays, which are easily opened for paper loading. For best results, use only SHARP recommended paper. (See page 58.) The paper required ( ) indicator will light up when there is no copy paper in the selected paper feed station, or when the selected paper tray is not installed or is improperly installed.
LOADING COPY PAPER GETTING STARTED Loading copy paper Changing the copy paper size in the tray Left guide 1 Gently lift and pull out the paper tray until it stops. 2 Push the pressure plate down until it locks in place. 3 Squeeze the lock lever of the front guide and slide the front guide to match the width of the paper. 4 Move the left guide to the appropriate slot as marked on the tray. ● When using 5-1/2" x 8-1/2" copy paper, load it into the upper paper tray.
LOADING COPY PAPER GETTING STARTED 9 Use the TRAY SELECT ( ) key to select the paper tray of which the paper size has been changed. ● ● 10 Each time the TRAY SELECT ( ) key is pressed, a paper tray will be indicated with a blinking paper feed location indicator. Use the ORIGINAL SIZE ENTER ( the paper size which is set. ● 11 The selected paper feed location indicator will blink and the corresponding paper size (which is currently set) indicator will light up steadily.
NORMAL COPYING This copier has two document input stations — a single pass feeder (SPF) for automatic document feeding and an original table for manual handling of bound documents. The SPF is designed to hold up to 30 originals measuring from 5-1/2" x 8-1/2" to 11" x 17" and in the weight range of 15 to 24 lbs. ● Before loading originals into the SPF, be sure to remove any staples or paper clips from them. ● ● ● Damaged or crumpled originals may misfeed in the SPF.
NORMAL COPYING Units digit 7 ● For photographs, select PHOTO ( ) and then adjust with the light ( ) and dark ( ) keys as desired. ● There are 5 exposure steps indicated by 3 indicator lights. (The indicators light up one or two at a time.) If exposure level 2 is selected, the two left-handmost indicators for that level will light up simultaneously. Also, if level 4 is selected, the two right-handmost indicators for that level will light up simultaneously.
NORMAL COPYING Using the original table Power on 1 Turn the power switch on. ● It will take about 35 seconds for the copier to warm up. However, you can make desired settings and press the START ( ) key during warm-up. Copying will start after warm-up. ● If the power is already on and all indicators except the POWER SAVE indicator are off, the copier is in the auto power shut-off mode. Press the START key in this case. See page 52, POWER SAVE MODES.
NORMAL COPYING Units digit 7 ● There are 5 exposure steps indicated by 3 indicator lights. (The indicators light up one or two at a time.) If exposure level 2 is selected, the two left-handmost indicators for that level will light up simultaneously. Also, if level 4 is selected, the two right-handmost indicators for that level will light up simultaneously. Set the number of copies using the two copy quantity ( , ) keys. ● Press the right copy quantity key to set the units digit from 0 to 9.
REDUCTION/ENLARGEMENT/ZOOM Reduction and enlargement ratios can be selected either automatically with the AUTO IMAGE ( ) key or manually with the PRESET RATIO selector ( , ) keys and/or the zoom ( , ) keys. The zoom function enables precise copy ratio selection from 50% to 200% in 1% increments. MAKING COPIES Automatic Reduction/enlargement/zoom 1 Place the original in the document feeder tray or on the original table.
REDUCTION/ENLARGEMENT/ZOOM 1 2 Place the original in the document feeder tray or on the original table. Use the PRESET RATIO selector ( , ) keys and the zoom ( , ) keys to select the desired copy ratio. To select a preset reduction or enlargement copy ratio, press the or key repeatedly until the indicator for the desired copy ratio is lit. Preset reduction ratios are: 95%, 77%, 64%, and 50% . Preset enlargement ratios are: 121%, 129%, 141%, and 200%.
BYPASS FEED (special paper) The bypass tray is used to copy onto transparency film, labels, and other special purpose papers. Up to 100 sheets of standard copy paper can be set in the bypass tray. For special purpose papers, the original image must be smaller than the paper or media for copying. If the original image is bigger than the paper or media, this may cause smudges on the edges of the copies.
BYPASS FEED (special paper) ) key to select the bypass 6 Press the START ( ) key. 23 Bypass feed (special paper) 5 Leave the copy quantity at 0 if using special papers. Set the number of copies if using standard copy paper or envelopes. MAKING COPIES 4 Press the TRAY SELECT ( tray.
TWO-SIDED COPYING Two-sided copies can be made on this copier using the bypass tray. MAKING COPIES 1 Place the first original on the original table and make a copy. ● Two-sided copying 2 The first copy can be made using any of the paper feed stations. Replace the first original with the second original and close the document feeder cover. ● ● Make sure that the first and second originals are oriented in the same way on the original table.
SORT/GROUP This copier has two sorter modes for different copying jobs: one sorts copies into sets matching the sequence of the originals and the second groups copies by originals. The sort/group feature cannot be used with the dual page copy feature. To change the SORT/GROUP mode, press the SORT/GROUP key to select the desired mode. ● The capacity of the paper output tray is 250 sheets.
SORT/GROUP Copying in the sort mode When copying in the sort mode, the original image will be stored in the copier memory each time an original is scanned and copying will start after all originals have been scanned. MAKING COPIES 1 Set the originals face up in the document feeder tray. 2 Press the SORT/GROUP key to select the SORT mode. 3 Ensure that the desired copy paper size is selected. 4 Set the number of copies and press the START ( ● The original table cannot be used for sort copying.
INTERRUPTING A COPY RUN INTERRUPT is used to interrupt a long copy run so that another job can be done. ● SORT or GROUP cannot be selected during interrupt copying. ) key. ● The copier will return to the initial settings. ● When the SPF is being used, the copier will stop after completing copying of the original which has been fed into the SPF. When the copier stops, remove the original(s) and set the original(s) for interrupt copying. 3 4 5 Select the desired available copier functions.
AUTOMATIC EXPOSURE ADJUSTMENT The automatic exposure level can be adjusted to suit your copying needs. This level is set for copying from the original table and copying from the SPF respectively. To set the level for the SPF, place an original in the document feeder tray and make sure that the SPF indicator lights up before proceeding to step 1. To set the level for the original table, ensure that the SPF indicator does not light up.
TONER SAVE MODE This mode reduces toner consumption by approximately 10% in the automatic and manual exposure modes. Copies will be lighter but still adequate for general use. Selection of this mode does not affect the PHOTO ( ) mode. Follow the procedure below for setting the toning level. / / / ● The MANUAL ( ) indicator will go out and the PHOTO ( indicator will begin to blink. ● The exposure indicator marked “5” will light up, indicating that the standard toner mode is active.
XY ZOOM Original Copy The XY ZOOM feature allows the horizontal and vertical copy ratios to be changed independently. To use the XY ZOOM feature with the DUAL PAGE COPY feature, set the DUAL PAGE COPY feature first and then the XY ZOOM feature. (Enlargement cannot be set.) SPECIAL FEATURES 1 Place the original in the document feeder tray or on the original table. 2 Press the XY-ZOOM ( ) key.
XY ZOOM 6 Press the copy ratio display ( ) key. ● The selected ratio for the horizontal direction will be entered and the display will change to the copy quantity display. ● To verify the copy ratios, press and hold down the copy ratio display ( ) key. The vertical and horizontal ratios will be alternately displayed. SPECIAL FEATURES 5 Use the PRESET RATIO selector ( , ) keys and , ) keys to change the copy ratio in the zoom ( horizontal direction in a similar manner as for the vertical direction.
B/W REVERSE Original Copy The B/W REVERSE feature is used to reverse black and white areas. SPECIAL FEATURES ● When the B/W REVERSE feature is selected, the exposure mode will be automatically set to the MANUAL mode. Other exposure modes cannot be selected. Even if this feature is canceled, the MANUAL mode will not automatically be canceled. 1 Place the original in the document feeder tray or on the original table. 2 Press the B/W REVERSE ( 3 Check the copy paper size.
DUAL PAGE COPY Original Copy The DUAL PAGE COPY feature produces individual copies of two documents placed side by side on the original table. It is especially useful when copying books and other bound documents. If the AUTO IMAGE feature has been selected, this feature cannot be selected. To use the DUAL PAGE COPY feature with the XY ZOOM feature, set the DUAL PAGE COPY feature first and then the XY ZOOM feature. (Enlargement cannot be set.
ROTATION COPYING Original Paper Copy Example: Copying from an 11" x 17" original onto 8-1/2" x 11" paper SPECIAL FEATURES Rotation copying 34 If user program No. 7 is set, the image of the original will rotate when the orientation of the original does not match that of the copy paper. Rotation copying will function only if the auto paper select mode or auto copy ratio mode has been selected. Even if user program No.
2 IN 1 OR 4 IN 1 2 in 1 copying Pattern Pattern Pattern Pattern The 2 in 1 or 4 in 1 feature is used to copy 2 or 4 originals, collectively in a specified order, onto one sheet. ● These features cannot be used with the dual page copying, XY zoom, erase, or margin shift features. ● Copies can be made with or without the border lines shown in the illustration. See user program No. 6 on page 49. ● The order of originals which will be arranged on the copies can be selected by user programs.
2 IN 1 OR 4 IN 1 4 Select the desired pattern number using copy quantity keys. ● SPECIAL FEATURES 2 in 1 or 4 in 1 36 The selected number will blink in the copy quantity display. For layout pattern numbers, see the previous page. 5 6 Press the START key. 7 Set the number of copies and press the START ( ● The selected number will light up steadily. Press the 2 IN 1 / 4 IN 1 key to complete the selection. ● ● The copy ratio will be calculated automatically.
ERASE Edge erase A A Center erase AB AB This copier has an edge erase mode and a center erase mode. ● Edge erase can be used to eliminate shadow lines around the edges of copies caused when thick paper or a book is used as an original. ● Center erase can be used to eliminate the shadow produced by the bindings of bound documents. ● Edge + center erase can be used to eliminate shadow lines around the edges of copies and to eliminate the shadow at the center of copies.
MARGIN SHIFT Original Copy The MARGIN SHIFT feature automatically shifts the text or image to the right to increase the left margin by approximately 1/4". ● This feature cannot be used with the 2 in 1 or 4 in 1 feature. Expanded margin Margin is expanded here. 1 Place the original in the document feeder tray or on the original table. ● SPECIAL FEATURES 2 Use the TRAY SELECT ( ) key to select the paper tray with the desired paper size. 3 Press the MARGIN SHIFT key.
TD CARTRIDGE REPLACEMENT If the machine detects an insufficient amount of toner available, copying will stop and the machine will add toner. During this time the TD cartridge replacement required ( ) indicator will blink. When sufficient toner has been added the indicator will go out indicating that copying can be resumed.
TD CARTRIDGE REPLACEMENT STATUS INDICATORS 5 Remove the protective cover from the TD cartridge by unlatching three cover hooks from the holes on the cartridge and then pulling the cover in the direction indicated by the arrow in the illustration. 6 Gently insert the TD cartridge along the guides until it locks in place. If dirt or dust is adhered to the TD cartridge, remove it before installing the cartridge.
DRUM CARTRIDGE REPLACEMENT The useful life of the drum cartridge is approximately 30,000 copies. When the internal counter reaches approximately 29,000 copies, the drum replacement required ( ) indicator will light up indicating that replacement of the drum cartridge will be needed soon. When the indicator begins to blink, replace the drum cartridge by following the procedure given below.
DRUM CARTRIDGE REPLACEMENT 5 Remove the new drum cartridge from the protective bag and gently insert the lead end of the drum cartridge along the guides. Do not touch the surface of the drum (green portion) of the cartridge. Doing so may cause smudges on the copies. STATUS INDICATORS Drum cartridge replacement 6 Remove the protective cover from the drum cartridge and then push the cartridge all the way into the copier. 7 Gently install the TD cartridge.
MISFEED REMOVAL The copier will stop when a misfeed occurs. The misfeed ( ) indicator will blink and blinking red misfeed location indicators will indicate the approximate misfeed location. If paper is accidentally torn during removal, be sure to remove all pieces. Be careful not to damage the photoconductive drum. First confirm the misfeed location. (P. 43) (P. 44, 47) (P.
MISFEED REMOVAL Location C 3 If the misfed original cannot be removed in steps 1 and 2, remove the misfed original from the exit area. Open the document feeder cover and rotate the roller in the direction indicated by the arrow if needed. If the misfed original cannot be easily removed from the exit area, open the front part of the document feeder tray to remove the original. 4 Open and close the document feeder cover to cancel the misfeed location indicator.
MISFEED REMOVAL 2 Check the misfeed location. Remove the misfed paper following the instructions for each location in the illustration below. If paper is misfed here, proceed to “B. Misfeed in the fusing area”. If the misfed paper is seen from this side, proceed to “C. Misfeed in the transport area”. If paper is misfed here, proceed to “A. Misfeed in the paper feed area”. A. Misfeed in the paper feed area 1 Push gently the right side of the front cover to open the cover.
MISFEED REMOVAL Roller rotating knob 2 Turn the roller rotating knob in the direction of the arrow. 3 Carefully remove the misfed paper. Lower the fusing unit release levers to allow easier removal. Return the release levers to their operating positions. Fusing unit release lever The fusing unit is hot. Take care in removing paper. ● ● 4 Do not touch the surface of the drum (green portion) of the drum cartridge when removing the misfed paper.
MISFEED REMOVAL 3 Close the side cover by pressing the handle on the cover. ● The misfeed ( ) indicator will go out. Misfeed in the upper paper tray Before opening the paper tray, be sure to open the bypass tray, lift slightly on the side cover and slide the cover out until it stops, and then perform steps 1 to 3 described in the “A. Misfeed in the paper feed area” section. 2 Close the paper tray. 3 Lift slightly on the side cover and slide the cover out until it stops.
MISFEED REMOVAL 2 Remove the misfed paper. 3 If the misfed paper is not seen in step 2, gently lift and pull out the lower paper tray and remove the misfed paper. ● ● STATUS INDICATORS Misfeed removal 48 Be careful not to tear the misfed paper during removal. Be careful not to tear the misfed paper during removal. 4 Close the paper tray. 5 Close the lower side cover. ● The misfeed ( ) indicator will go out.
USER PROGRAMS The user programs allow the parameters of certain functions to be set, changed, or canceled as desired. List of user programs This copier has the following user programs. Program No. Program name Description 1 Auto clear time Sets the auto clear time. The copier returns to the initial settings when the auto clear time elapses after the last copy is made. 2 Preheat mode Sets the time that elapses before the copier enters the preheat mode after any operation is made. See page 52.
USER PROGRAMS 2 Enter a program number using the left copy quantity ) key. ( ● The selected program number will blink in the copy quantity display. ● If a mistake is made in steps 2 to 4, press the CLEAR ( copier will return to step 2. ● The program numbers are shown in the table on the previous page. ) key. The For example, to change the setting of the auto power shut-off timer, enter 3. 3 Press the START ( 4 Select the desired parameter using the right copy quantity ( ) key. ● ) key.
USER PROGRAMS 5 Press the START ( 6 To continue with other user programs, press the CLEAR ( ) key and then repeat steps 2 to 5. To exit the user ) key. program mode, press the light ( ● ● ) key. The right-hand number in the copy quantity display will be steadily lit and the entered value will be stored. All the alarm indicators will go out.
POWER SAVE MODES The copier has two power save modes to reduce overall power consumption thereby reducing the cost of operation. In addition, these modes conserve natural resources and help reduce environmental pollution. The two power save modes are preheat mode and auto power shut-off mode. ● User programs The preheat activation time and the auto power shut-off time have been preset at the factory to 90 sec. for preheat mode and 30 min. for auto power shut-off mode.
POWER SAVE MODES Setting the power save modes The time that elapses before the copier enters a power save mode after any operation is made can be set manually. This time is set with user program No. 2 for the preheat mode and user program No. 3 for the auto power shut-off mode. For these settings, see page 49. ● The copier will enter the preheat mode first and then the auto power shutoff mode after a preset time has elapsed when no copier operation has been made.
USER MAINTENANCE Proper care is essential for clean, sharp copies. Please take a few minutes to regularly clean your copier. Original table and document feeder cover Stains or dirt on the original table or document feeder cover will also be copied. Wipe the original table and document feeder cover with a soft, clean cloth. ● If necessary, dampen the cloth with water. Do not use thinner, benzene, or similar volatile cleaning agents. ● Also wipe the scanning window on the orignal table.
USER MAINTENANCE Charger cleaner 1 2 Turn the power switch off. 3 Gently lift and pull out the upper paper tray and take the charger cleaner out by holding the tab. 4 Set the charger cleaner onto the transfer charger and gently slide the cleaner in the direction indicated by the arrow two or three times. Open the bypass tray. Lift slightly on the side cover and slide the cover out until it stops. If the white sheet metal is smudged with toner, wipe it with a soft, clean cloth.
COPIER TROUBLE? Problem Solution ● Copier plugged in? Plug the copier into a grounded outlet. See page 8. ● Power switch ON? Turn the power switch ON. See page 16. ● Copy density properly adjusted? See pages 16 and 28. ● Is the original placed face down on the original table or face up in the SPF? Place the original face down on the original table or face up in the SPF. ● Paper too heavy? Use copy paper within the specified range. See page 58. ● Paper damp? Replace with dry copy paper.
COPIER TROUBLE? Problem Power is on but copying is not possible. Lighting fixture flickers. Solution ● Is the POWER SAVE ( indicator blinking? ) ● Is the indicator on? Copy paper is needed. See page 13, LOADING COPY PAPER. ● Is blinking in the copy quantity display? The TD cartridge is not installed. Install the TD cartridge. ● Is steadily lit in the copy quantity display? Side cover(s) is open. Close the front and side covers securely.
SUPPLIES Types and sizes of copy paper Size Weight Capacity (21 lb. bond paper) Paper tray 5-1/2" x 8-1/2"* to 11" x 17" 15 lbs. to 21 lbs. 250 sheets Bypass tray Ordinary paper: 5-1/2" x 8-1/2" to 11" x 17" Envelopes: Commercial 10 (4-1/8" x 9-1/2") International DL (110 x 220 mm) International C5 (162 x 229 mm) 15 lbs. to 34 lbs.
SUPPLIES Genuine supplies statement Standard supplies for this copier that are to be replaced by the user are copy paper, TD cartridge, and drum cartridge. For best copying results, be sure to use only SHARP Genuine Supplies which are designed, engineered and tested to maximize the life and performance of SHARP copiers. Look for the Genuine Supplies label on the TD cartridge and drum cartridge. GENUINE SUPPLIES Proper storage 1. 2.
MOVING INSTRUCTIONS When moving this copier, follow the procedure below. When moving this copier, be sure to remove the TD cartridge in advance. TD cartridge lock release lever 1 Turn the power switch off and disconnect the power cord. 2 Open the bypass tray. Lift slightly on the side cover and slide the cover out until it stops. Push gently the right side of the front cover to open the cover.
SPECIFICATIONS COPIER Copy system Dry, electrostatic transfer Originals Sheets, bound documents Original sizes Max. 11" x 17" Copy sizes Max. 11" x 17" Min. 5-1/2" x 8-1/2" Image loss: Max. 5/32" (4 mm) (at the leading edge) Max. 5/32" (4 mm) (at the trailing edge)* Max. 5/32" (4 mm) (along other edges in total) * Max. can be 15/64" (6 mm) with the copies made from the SPF. Copying speed (at 100% copy ratio) 16 copies/min. (8-1/2" x 11") 12 copies/min. (8-1/2" x 11"R) 10 copies/min.
SPECIFICATIONS Overall dimensions (with bypass tray folded) 23-15/64" (W) x 20-23/32" (D) (590 mm (W) x 526 mm (D)) Weight Approx. 92.7 lbs. (42 kg) TD and drum cartridges included Copier dimensions 23-15/64" (W) x 20-23/32" (D) x 25-3/4" (H) (590 mm (W) x 526 mm (D) x 654 mm (H)) Operating conditions Temperature: 59°F to 86°F (15°C to 30°C) Humidity: 20% to 85% SINGLE PASS FEEDER Acceptable originals Weight: 15 to 24 lbs.
INDEX 2 2 in 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 G Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 4 4 in 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 I Initial settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 A Auto clear . . . . . . . . . . . . . . . . . . . . . . . . .
INDEX R Reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Replacement – drum cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – TD cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Rotation copying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 41 39 34 S Screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11, 60 Single pass feeder (SPF) . . . . . . . . . . . . . . . . . . . 5, 16, 62 Sort . . .
S H A R P Date Issued:Nov. 1, 1998 MATERIAL SAFETY DATA SHEET MSDS No. F-00841 Section 1. Product Identification Product: AL-160TD (Black Toner) Section 2. Supplier’s Name and Address Sharp Corporation 22-22 Nagaike-cho, Abeno-ku, Osaka, Japan Local suppliers are listed below. Please contact the nearest supplier for additional information. (Country) U.S.A. Canada United Kingdom Section 3. Ingredients Ingredients Styrene-Acrylate copolymer Carbon black Iron oxide Metal Complex dye Section 4.
Section 6. Physical Chemical Characteristics Boiling / Melting Point: Vapor Pressure: Vapor Density: Evaporation Rate: Appearance: Odor: Section 7. Not applicable Not applicable Not applicable Not applicable Fine powder Odorless Not applicable >350°C (LEL); Not applicable (UEL); Not applicable CO2, dry chemical, foam or water None This material has no unusual fire or explosion hazards.
S H A R P Date Issued :Nov. 1, 1998 MATERIAL SAFETY DATA SHEET MSDS No. F-30841 Section 1. Product Identification Product AL-160TD(Black Developer) Section 2. Supplier’s Name and Address Sharp Corporation 22-22 Nagaike-cho, Abeno-ku, Osaka, Japan Local suppliers are listed below. Please contact the nearest supplier for additional information. (Country) U.S.A. Canada United Kingdom Section 3. Ingredients Ingredients Iron powder Styrene-Acrylate copolymer Carbon black Section 4.
Section 6. Physical Chemical Characteristics Boiling / Melting Point: Vapor Pressure: Vapor Density: Evaporation Rate: Appearance: Odor: Section 7. Not applicable Not applicable Not applicable Not applicable Fine powder Odorless Not applicable >350°C (LEL); Not applicable (UEL); Not applicable CO2, dry chemical, foam or water None This material has no unusual fire or explosion hazards.
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
AL-1670 SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430-2135. www.sharp-usa.