Service manual

AL-2051 USER PROGRAM 11 - 1
[11] USER PROGRAM
The user settings allow you to customize machine settings to better meet your needs.
1. User programs
The user settings consist of the following items.
To change the user program settings as explained in "SELECTING A SETTING FOR A USER PROGRAM".
Copy mode
Program
number
Program name
Setting codes
(factory default setting
appears in bold)
Explanation
1 AUTO CLEAR 1: 10 SEC.
2: 30 SEC.
3: 60 SEC.
4: 90 SEC.
5: 120 SEC.
6: OFF
• Auto clear time automatically returns the copy settings to the initial set-
tings if no keys are pressed for a preset period of time following the end of
a copy job.
• This program is used to select the period of time. Auto clear time can also
be disabled.
2 PREHEAT MODE 1: 30 SEC.
2: 1 MIN.
3: 5 MIN.
4: 30 MIN.
5: 60 MIN.
6: 120 MIN.
7: 240 MIN.
• This function automatically switches the machine to a low power con-
sumption state if the set duration of time elapses without the machine
being used when the power is on. The power save indicator lights up,
however, the keys on the operation panel can be used. Normal operation
automatically resumes when a key on the operation panel is pressed, an
original is placed, a print job is received.
3AUTO SHUT-OFF 1: ON
2: OFF
• Use this setting to enable or disable auto power shut-off mode.
4 AUTO SHUT-OFF TIME 1: 5 MIN.
2: 30 MIN.
3: 60 MIN.
4: 120 MIN.
5: 240 MIN.
• This function automatically switches the machine to a state that consumes
even less power than preheat mode if the set duration of time elapses
without the machine being used when the power is on. All lights except
the power save indicator go off. To resume normal operation, press the
[START] key ( ). Normal operation also resumes automatically when a
print job is received or scanning is begun from a computer. While in auto
power shut-off mode, no keys (except the [START] key ( )) can be
used.
7 LAYOUT IN 2IN1 1: PATTERN 1
2: PATTERN 2
• Use this setting to select the layout pattern when two original pages are
copied onto a single sheet of paper.
8 OFFSET FUNCTION 1: ON
2: OFF
• When enabled, this function offsets the position in the paper output tray of
sets of copies during copy job, and print jobs when using the printer func-
tion.
9 ROTATE ORIG.IMAGE 1:
ON
2: OFF
• When two-sided copying is performed, this function rotates the image on
the back of the original. This is convenient when binding the copies at the
top (tablet binding).
10 AE/TEXT
RESOLUTION
1: 300dpi
2: 600dpi
• This setting is used to change the copy resolution in AUTO and TEXT
mode from 600 x 300 dpi to 600 x 600 dpi (highquality mode). Scanning is
slower when high-quality mode is used.
11 2-SIDED COPY MODE 1: HI-SPEED
2: NORMAL
• If the memory fills up when two-sided copying is performed, "NORMAL"
can be selected to make copying possible. However, "NORMAL" results in
a slower copying speed. Normally "HISPEED" is selected to enable fast
two-sided copying.
12 MARGIN WIDTH 1: 5 mm
2: 10 mm
3: 15 mm
4: 20 mm
• Use this setting to set the margin width.
13 MEM. FOR PRINTER 1: 30%
2: 40%
3: 50%
4: 60%
5: 70%
• Use this to change the proportion of machine memory used for printer
mode.
14 AUTO KEY REPEAT 1: ON
2: OFF
• Use this setting to select whether or not holding down a key causes
repeated input of the key. For keys that normally cause a set value to
increase when held down (for example, holding down the [ ] key ( )
or [ ] key ( )), this program can be used to have the set value not
change when the key is held down.
15 KEY PRESS TIME 1: NORMAL
2: 0.5 SEC.
3: 1.0 SEC.
4: 1.5 SEC.
5: 2.0 SEC.
• Use this setting to select how long a key must be pressed for the input to
be accepted. By selecting a longer time, you can prevent settings from
being changed by the accidental pressing of a key.