Service manual

AL-2051 UNPACKING AND INSTALLATION 5 - 5
Installing the Utility Software
11) When installing is finished, click the "Close" button.
Caution:
• If you are using Windows Vista or 7 and a security warning
window appears, be sure to click "Install this driver software
anyway".
• If you are running Windows 2000/XP and a warning message
appears regarding the Windows logo test or digital signature,
be sure to click "Continue Anyway" or "Yes".
A message will appear instructing you to connect the machine
to your computer. Click the "OK" button.
Note: After the installation, a message prompting you to restart
your computer may appear. In this case, click the "Yes"
button to restart your computer.
12) Make sure that the power of the machine is turned on, and then
connect the USB cable.
Windows will detect the machine and a Plug and Play screen
will appear.
13) Follow the instructions in the plug and play window to install the
driver.
Follow the on-screen instructions.
Caution:
• If you are using Windows Vista or 7 and a security warning
window appears, be sure to click "Install this driver software
anyway".
• If you are running Windows 2000/XP and a warning message
appears regarding the Windows logo test or digital signature,
be sure to click "Continue Anyway" or "Yes".
This completes the installation of the software.
If you installed Button Manager, set up Button Manager as
explained in "SETTING UP BUTTON MANAGER".
(2) Connecting a USB cable
Follow the procedure below to connect the machine to your com-
puter.
A USB cable for connecting the machine to your computer is not
included with the machine. Please purchase the appropriate cable
for your computer.
Caution:
• USB is available with a PC/AT compatible computer that was
originally equipped with USB and had Windows 2000 Profes-
sional, Windows XP, Windows Vista or Windows 7 preinstalled.
• Do not connect the USB cable before installing the printer driver.
The USB cable should be connected during installation of the
printer driver.
Note:
• If the machine will be connected using a USB 2.0 port of your
computer, please purchase a USB cable that supports USB 2.0.
• To obtain the fastest USB 2.0 data transfer speed, "USB2.0
MODE SWITCH" in the machine's user programs must be set to
"HISPEED". For more information, see "USER PROGRAMS".
• Use the machine's "HI-SPEED" mode only when using a com-
puter that is running Windows 2000/XP/Vista or 7.
• Even when the Microsoft USB 2.0 driver is used, it may not be
possible to obtain full USB 2.0 speed if a PC card supporting
USB 2.0 is used. To obtain the latest driver (which may enable a
higher speed), contact the manufacturer of your PC card.
• Connection is also possible using a USB 1.1 port on your com-
puter.
However, the specifications will be USB 1.1 specifications (Full-
Speed).
1) Insert the cable into the USB connector on the machine.
2) Insert the other end of the cable into your computer's USB port.
(3) Using the machine as a network printer
Note: Interface cables for connecting the machine to your
computer are not included with the machine. Please
purchase the appropriate cable for your computer.
1) Insert the LAN cable into the LAN connector on the machine.
Use a network cable that is shielded.
2) Turn on the machine.
3) Insert the "Software CD-ROM" (Disc 1) into your computer's
CD-ROM drive.
4) Click the "start" button, click "My Computer" ( ), and then
double-click the CD-ROM icon ( ).
• In Windows Vista/7, click the "Start" button, click "Computer",
and then double-click the "CD-ROM" icon.
• In Windows 2000, double-click "My Computer" and then dou-
ble-click the CD-ROM icon.
5) Double-click the "setup" icon ( ).
In Windows Vista/7, if a message screen appears asking you
for confirmation, click "Allow".
6) The "SOFTWARE LICENSE" window will appear. Make sure
that you understand the contents of the license agreement, and
then click the "Yes" button.
Note: You can show the "SOFTWARE LICENSE" in a different
language by selecting the desired language from the
language menu. To install the software in the selected
language, continue the installation with that language
selected.
7) Read the message in the "Welcome" window and then click the
"Next" button.