TopPage LC-52/60/70LE640U,C6400U (1st Edition) SERVICE MANUAL No. S12V452LE640U LCD COLOR TELEVISION MODELS LC-52LE640U LC-52C6400U LC-60LE640U LC-60C6400U LC-70LE640U LC-70C6400U In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used. CONTENTS SAFETY PRECAUTION IMPORTANT SERVICE SAFETY PRECAUTION ............................................................
LC-52/60/70LE640U,C6400U (1st Edition) LC52LE640U SAFETY PRECAUTION Service Manual IMPORTANT SERVICE SAFETY PRECAUTION Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the servicing guidelines which follow: WARNING • Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.
LC-52/60/70LE640U,C6400U (1st Edition) PRECAUTIONS A PRENDRE LORS DE LA REPARATION Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement accoutumé à toute vérification de sécurité et aux conseils suivants. AVERTISSEMENT • A l'aide de deux fils à pinces, brancher une résistance de 1.5 kΩ 10 watts en parallèle avec un condensateur de 0.
LC-52/60/70LE640U,C6400U (1st Edition) PRECAUTIONS FOR USING LEAD-FREE SOLDER Employing lead-free solder • “PWBs” of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The alphabetical character following LF shows the type of lead-free solder. Example: Indicates lead-free solder of tin, silver and copper. Indicates lead-free solder of tin, silver and copper.
LC-52/60/70LE640U,C6400U (1st Edition) LC52LE640U OUTLINE Service Manual MAJOR SERVICE PARTS PWB Unit Ref No. N N N N N N N N N N N N N Parts No.
LC-52/60/70LE640U,C6400U (1st Edition) CHAPTER 1.
LC-52/60/70LE640U,C6400U (1st Edition) CHAPTER 2.
LC-52/60/70LE640U,C6400U (1st Edition) Remote Control Unit 1 18 2 19 3 4 5 20 21 1 POWER: Switch the TV power on or enter standby. 2 TV, STB, DVD.VCR, AUDIO: Switches the remote control for TV, STB, BD, DVD, VCR and AUDIO operation. * To enter the code registration mode, you need to press an appropriate button (STB, DVD VCR or AUDIO) and DISPLAY at the same time. 3 External equipment operational buttons: Operate the external equipment. 4 OPTION: Display the Link Operation Menu screen.
LC-52/60/70LE640U,C6400U (1st Edition) QUICK REFERENCE Attaching the Stand • Before attaching (or detaching) the stand, unplug the AC cord. • Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being damaged. CAUTION • • • • 1 Attach the stand in the correct direction. Do not remove the stand from the TV unless using an optional wall mount bracket to mount it. Be sure to follow the instructions.
LC-52/60/70LE640U,C6400U (1st Edition) CHAPTER 3. DIMENSIONS LC52LE640U Service Manual [1] DIMENSIONS (LC-52LE640U/C6400U) LC-52LE640U/LC-52C6400U 1 3/ 64 (26.4)*2 47 9/ 16 (1208) 2 27/ 32 (72) 5 41/ 64 (143) 16 1/ 2 (419) 5° (400) 15 3/ 4 43/ 64 8 15/ 32 (215) 4 1/ 2 (114) 6 17/ 64 (159) AN-52AG4 *1 *2 2 1/ 64 (51) (400) (17) 15 13 1/ 8 (333) 15 25/ 64 (391) 13 19/ 32 (345) 21 7/ 64 (536) 11 17/ 64 (286) 25 33/ 64 (648.0)*1 29 3/ 32 (739) 30 23/ 64 (771) 45 23/ 64 (1152.
LC-52/60/70LE640U,C6400U (1st Edition) [2] DIMENSIONS (LC-60/70LE640U,C6400U) LC-70LE640U/LC-70C6400U 63 19/ 32 (1615) 3 1/ 2 (89) 5 23/ 64 (136) 10 23/ 64 (263) 21 3/ 16 (538) 34 3/ 32 (865.62)*1 38 7/ 16 (976) 60 19/ 32 (1538.
LC-52/60/70LE640U,C6400U (1st Edition) Service CHAPTER 4. REMOVING OF MAJOR PARTS LC52LE640U Manual [1] REMOVING OF MAJOR PARTS (LC-52LE640U/C6400U) 1. Removing of Stand Unit and Rear Cabinet. 1. Remove the 4 lock screws 2. Remove the 1 lock screw and detach the Stand Unit . and detach the AC Cord Cover 3. Disconnect AC wire and detach the AC Cord 4. Remove the 4 VESA Hole Covers . . , 11 lock screws , 3 lock screws and 17 lock screws and detach the Rear Cabinet .
LC-52/60/70LE640U,C6400U (1st Edition) [Precautions when fixing the Rear Cabinet] When fixing the Rear Cabinet, be careful not to catch the backlight LED harness, speaker harness and other harnesses in it. • The hooks on the external wall of the Rear Cabinet are fitted in the Front Cabinet Ass’y. After putting the Rear Cabinet in place, fit the hooks securely; then tighten the screws.
LC-52/60/70LE640U,C6400U (1st Edition) 2. Removing of Speaker (L/R), KEY Unit and Fixing Metal Angle. 1. Detach the Bottom Cover 2. Disconnect the SP wire. 3. Detach the Speaker (L) , Speaker (R) . 4. Disconnect the RC wire. 5. Detach the KEY Unit Ass’y . 6. Disconnect the KM wire. 7. Remove the 2 lock screws 8. Detach the KEY Unit and detach the Key Button from Key Button 9. Remove the 19 lock screws from Key Button Cover . . and detach the Fixing Metal Angle .
LC-52/60/70LE640U,C6400U (1st Edition) 3. Removing of Connectors 1. Disconnect the following connectors from the MAIN Unit. (PD, LV, PL, Cl, UB) 2. Disconnect the following connectors from the POWER/DRIVE Unit. (PD, LA) 3. Disconnect the following connectors from the LCD CONTROL Unit.
LC-52/60/70LE640U,C6400U (1st Edition) 4. Removing of 60” LCD Panel Module Unit, LCD CONTROL Unit, MAIN Unit, POWER/DRIVE Unit. 1. Remove the 8 lock screws . 2. Detach the 14 Fixing Metal Angles . 3. Remove the 8 Hooks and detach the 60” LCD Panel Module Unit 4. Remove the 2 Connecting Cords , 2 Ferrite Cores . and 6 lock screws 5. Remove the 5 lock screws and detach the Shield (MAIN Unit) 6. Remove the 3 lock screws and detach the MAIN Unit 7.
LC-52/60/70LE640U,C6400U (1st Edition) 5. Removing of R/C OPC Unit, ICON Unit, WiFi Unit. 1. Detach the R/C OPC Unit . 2. Disconnect the RA wire. 3. Remove the 1 lock screw and detach the ICON Unit . 4. Disconnect the CI wire. 5. Detach the WiFi Unit . 6. Disconnect the UB wire.
LC-52/60/70LE640U,C6400U (1st Edition) [2] REMOVING OF MAJOR PARTS (LC-60LE640U/C6400U) 1. Removing of Stand Unit and Rear Cabinet. 1. Remove the 4 lock screws 2. Remove the 1 lock screw and detach the Stand Unit . and detach the AC Cord Cover 3. Disconnect AC wire and detach the AC Cord 4. Remove the 4 VESA Hole Covers . . , 11 lock screws , 20 lock screws and detach the Rear Cabinet .
LC-52/60/70LE640U,C6400U (1st Edition) [Precautions when fixing the Rear Cabinet] When fixing the Rear Cabinet, be careful not to catch the backlight LED harness, speaker harness and other harnesses in it. • The hooks on the external wall of the Rear Cabinet are fitted in the Front Cabinet Ass’y. After putting the Rear Cabinet in place, fit the hooks securely; then tighten the screws.
LC-52/60/70LE640U,C6400U (1st Edition) 2. Removing of Speaker (L/R), KEY Unit and Fixing Metal Angle. 1. Detach the Speaker (L) , Speaker (R) . 2. Disconnect the SP wire. 3. Disconnect the RC wire. 4. Detach the KEY Unit Ass’y . 5. Disconnect the KM wire. 6. Remove the 2 lock screws 7. Detach the KEY Unit and detach the Key Button from Key Button from Key Button Cover . . 8. Remove the 4 Hooks and detach the 2 Bottom Cover .
LC-52/60/70LE640U,C6400U (1st Edition) 3. Removing of Connectors 1. Disconnect the following connectors from the MAIN Unit. (PD, LV, PL, Cl, UB) 2. Disconnect the following connectors from the POWER/DRIVE Unit. (PD, LA) 3. Disconnect the following connectors from the LCD CONTROL Unit.
LC-52/60/70LE640U,C6400U (1st Edition) 4. Removing of 60” LCD Panel Module Unit, LCD CONTROL Unit, MAIN Unit, POWER/DRIVE Unit. 1. Remove the 21 Hooks and detach the 60” LCD Panel Module Unit 2. Remove the 2 Connecting Cords , 2 Ferrite Cores . and 6 lock screws 3. Remove the 5 lock screws and detach the MAIN PWB Shield 4. Remove the 3 lock screws and detach the MAIN Unit 5. Remove the 6 lock screws and detach the POWER/DRIVE Unit 6. Remove the 12 lock screws and detach the 2 Support Ass’y 7.
LC-52/60/70LE640U,C6400U (1st Edition) 5. Removing of R/C OPC Unit, ICON Unit, WiFi Unit. 1. Detach the R/C OPC Unit . 2. Disconnect the RA wire. 3. Detach the ICON Unit . 4. Disconnect the CI wire. 5. Detach the Wi-Fi Unit . 6. Disconnect the UB wire.
LC-52/60/70LE640U,C6400U (1st Edition) [3] REMOVING OF MAJOR PARTS (LC-70LE640U/C6400U) 1. Removing of Stand Unit and Rear Cabinet Ass’y. 1. Remove the 4 lock screws 2. Remove the 1 lock screw and detach the Stand Unit . and detach the AC Cord Cover 3. Disconnect AC wire and detach the AC Cord 4. Remove the 4 VESA Hole Covers . . , 9 lock screws and 21 lock screws and detach the Rear Cabinet Ass’y .
LC-52/60/70LE640U,C6400U (1st Edition) [Precautions for assembly] Push Push Push CAUTION Set it so that there may not be a clearance between Front Cabinet Ass'y and Rear Cabinet Ass'y. Push Push The fingernail is surely fixed when Rear cabinet Ass'y is firmly pushed, and the gap disappears. There is a gap without the fingernail fitting in completely only when covering with Rear Cabinet Ass'y.
LC-52/60/70LE640U,C6400U (1st Edition) 2. Removing of Speaker (L/R) and KEY Unit. 1. Disconnect the SP wire. 2. Remove the 2 lock screws and detach the Speaker (L) , Speaker (R) . 3. Disconnect the RC wire. 4. Detach the KEY Unit Ass’y . 5. Disconnect the KM wire. 6. Remove the 2 lock screws 7. Detach the KEY Unit and detach the Key Button from Key Button from Key Button Cover . . 8. Remove the 4 Hooks and detach the 2 Bottom Cover .
LC-52/60/70LE640U,C6400U (1st Edition) 3. Removing of Connectors 1. Disconnect the following connectors from the MAIN Unit. (PD, LV, PL, Cl, UB) 2. Disconnect the following connectors from the POWER/DRIVE Unit. (PD, LA) 3. Disconnect the following connectors from the LCD CONTROL Unit.
LC-52/60/70LE640U,C6400U (1st Edition) 4. Removing of 70” LCD Panel Module Unit, LCD CONTROL Unit, MAIN Unit, POWER Unit. 1. Remove the 24 Hooks and detach the 70” LCD Panel Module Unit 2. Remove the 2 Connecting Cords , 2 Ferrite Cores . , 6 lock screws 3. Remove the 2 look screws and detach the 2 Spacers 4. Remove the 6 lock screws and detach the POWER Unit and detach the LCD CONTROL Unit . . . 5. Remove the 5 lock screws and detach the MAIN PWB Shield 6.
LC-52/60/70LE640U,C6400U (1st Edition) 5. Removing of R/C OPC Unit, ICON Unit, WiFi Unit. 1. Detach the R/C OPC Unit . 2. Disconnect the RA wire. 3. Detach the ICON Unit . 4. Disconnect the CI wire. 5. Detach the Wi-Fi Unit . 6. Disconnect the UB wire.
LC-52/60/70LE640U,C6400U (1st Edition) [4] The location putting on the heat measure sheet 1. MAIN PWB Unit • LC-60LE640U/C6400U Put 䇼PSPAZC805WJKZ䇽 along these ruled lines. • LC-70LE640U/6400U PSPAZC741WJKZ 835 2.
LC-52/60/70LE640U,C6400U (1st Edition) [5] Precautions for assembly 1. Points to be checked and precautions when servicing the unit Mount the main PWB Ass’y on the backlight chassis and check that the EMI-prevention parts are not peeled and twisted from the access holes. (The EMI-prevention parts, conductive nonwoven fabric gaskets, must be seen from the access holes.) [Countermeasure] Attach the conductive nonwoven fabric gaskets on the shielded case on the main PWB.
LC-52/60/70LE640U,C6400U (1st Edition) • LC-70LE640U/C6400U PMLT-A691WJQZ PMLT-A690WJQZ PMLT-A690WJQZ PMLT-A691WJQZ 4 – 21
LC-52/60/70LE640U,C6400U (1st Edition) State where the main PWB and shielded case are assembled Access hole Access hole The following is a drawing mounting the main PWB Ass’y on the backlight chassis. (The parts indicated by -> are the access holes for confirmation.
LC-52/60/70LE640U,C6400U (1st Edition) CHAPTER 5. ADJUSTMENT LC52LE640U Service Manual [1] ADJUSTMENT PROCEDURE The adjustment values are set to the optimum conditions at the factory before shipping. If a value should become improper or an adjustment is required due to part replacement, make an adjustment according to the following procedure. 1. After replacement of any PWB unit and/or IC for repair, please note the following.
LC-52/60/70LE640U,C6400U (1st Edition) 2.2.3 How to upgrade the software 1. Unplug the AC cord. 2. Insert the USB Memory for version upgrade into the service socket. 3. Plug in the AC cord with power button pressed down. 4. After 5 seconds, unpress the power button. 5. After the unit startup, the system upgrade screen as shown below within 20-40 seconds.
LC-52/60/70LE640U,C6400U (1st Edition) 2.3. Monitor microprocessor software version upgrade Create the USB memory for monitor microprocessor software version upgrade in the same manner as explained in the “Main software version upgrade”. Copy the file BSMK_LE640_xxx.USB and BM2SMxxx.SMB. (named temporarily) for monitor microprocessor software version upgrade to the USB memory. 2.3.1 How to upgrade the software 1. Unplug the AC cord. 2. Insert the USB Memory for version upgrade into the service socket. 3.
LC-52/60/70LE640U,C6400U (1st Edition) 3. Entering and exiting the adjustment process mode 1) Before entering the adjustment process mode, the AV position RESET in the video adjustment menu. 2) While holding down the “VOL (–)” and “INPUT” keys at a time, plug in the AC cord of the main unit to turn on the power. The letter “” appears on the screen. 3) Next, hold down the “VOL (–)” and “CH ( (The “VOL (–)” and “CH ( )” keys at a time. )” keys should be pressed and held until the display appears.
LC-52/60/70LE640U,C6400U (1st Edition) 5. List of adjustment process mode menu The character string in brackets [ ] will appear as a page title in the adjustment process menu header.
LC-52/60/70LE640U,C6400U (1st Edition) Page 7 8 9 10 11 12 13 Line 1 2 3 4 5 6 7 8 1 1 2 3 4 5 6 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 10 11 12 1 2 3 4 5 6 7 8 9 10 11 12 13 Item ANALOG RGB ADJ R A_GAIN G A_GAIN B A_GAIN R OFFSET G OFFSET B OFFSET RGB_A_CLAMP VCOM ADJ LEV1 LEV2 LEV3 LEV4 LEV5 LEV6 MG1R MG1G MG1B MG2R MG2G MG2B MG3R MG3G MG3B MG4R MG4G MG4B MG5R MG5G MG5B MG6R MG6G MG6B LO R 1 LO G 1 LO B 1 LO Y 1 LO R 2 LO G 2 LO B 2 LO Y 2 LO R 3 LO G 3 LO B 3 LO Y 3 LO R 4 LO G 4 LO
LC-52/60/70LE640U,C6400U (1st Edition) Page 14 15 16 17 18 19 20 21 Line 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 9 1 2 3 1 2 3 4 5 6 7 1 2 3 4 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 9 10 11 Item MODE SELECT POS SELECT POS MIN POS MID1 POS MID2 POS MID3 POS MID4 POS MID5 POS MID6 POS MAX CD MIN CD MID1 CD MID2 CD MID3 CD MID4 CD MID5 CD MID6 CD MAX CALC RESET VAL1 VAL2 VAL3 VAL4 VAL5 VAL6 GAMMA ADJ TEMP MONITOR TIME OUT MONITOR MAX TEMP MONITOR ERROR CAUSE RESET LCD TEST PATTERN LCD TEST PATTE
LC-52/60/70LE640U,C6400U (1st Edition) Page 22 23 24 25 26 27 28 Line 1 2 3 4 5 6 7 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 7 8 9 10 11 12 13 Item POWER KEY SENSITIVITY MENU KEY SENSITIVITY INPUT KEY SENSITIVITY CH UP KEY SENSITIVITY CH DOWN KEY SENSITIVITY VOL UP KEY SENSITIVITY VOL DOWN KEY SENSITIVITY KEY STRENGTH GET MODE POWER KEY STRENGTH MENU KEY STRENGTH INPUT KEY STRENGTH CH UP KEY STRENGTH CH DOWN KEY STRENGTH VOL UP KEY STRENGTH VOL DOWN KEY STR
LC-52/60/70LE640U,C6400U (1st Edition) *1 Details of P1.12 (NORMAL STANDBY CAUSE) When TV set is powered off due to normal use or product specification, the last cause will be recorded. The code, character string and description for the standby cause are below. If you power off by remote, the cause will not be recorded. Code 2 3 6 8 Character string NO_OPERT NO_SIGNA SLEEP_TM OFF_232C Description No operation off No signal off Off timer Command from RS232C *2 Details of P1.
LC-52/60/70LE640U,C6400U (1st Edition) 6. Special features * STANDBY CAUSE (Page 1/28) Display of a cause (code) of the last standby The cause of the last standby is recorded in EEPROM whenever possible. Checking this code will be useful in finding a problem when you repair the troubled set. * EEP SAVE (Page 28/28) * EEP RECOVER (Page 28/28) Storage of EEP adjustment value Retrieval of EEP adjustment value from storage area 7. Writing the microprocessor software 7.1.
LC-52/60/70LE640U,C6400U (1st Edition) 8.2. Image adjustment 8.2.1 Device check Before adjustment, check that the adjustment jig and signal source are set for Sharp LCD US. Signal generator level adjustment check (Adjust to the standard value level.) • Composite signal: • 15K component signal: • 33K component signal: • Analog RGB: Y level: PB/PR level: Y level: PB/PR level: RGB level: 0.714Vp-p ± 0.02Vp-p (Pedestal to white) 0.714Vp-p± 0.02Vp-p (Pedestal to white) 0.7Vp-p ± 0.02Vp-p 0.7Vp-p ± 0.
LC-52/60/70LE640U,C6400U (1st Edition) 8.2.5 Component 33K signal adjustment 1 Adjustment point Setting Adjustment conditions 1080i signal Adjustment procedure • Send the 100% color bar signal to the component input. Color saturation: 100% 100% white 2 Automatic adjustment execution 1080i 100% color bar 0% black Point the cursor to [ COMP33K ADJ(INPUT1)] and press the [Enter] key. The adjustment is complete when [ COMP33K ADJ(INPUT1) OK] is displayed. 8.2.
LC-52/60/70LE640U,C6400U (1st Edition) 9. White balance adjustment 9.1. White balance adjustment (For details about the adjustment procedure, refer to “Kameyama Model Integrated Monitor WB Adjustment Specification V1.92”.
LC-52/60/70LE640U,C6400U (1st Edition) 10. Key writing 10.1. EDID writing (Main PWB: QPWBXF733WJN2) 1. Write the MAC key data on IC8455 mounted on the main PWB. 2. Carry out thorough data management to avoid redundant writing of data. If the IC where data is written is damaged, replace the PWB since only the IC cannot be changed. 10.2. MAC key writing (MAIN PWB: QPWBXF733WJN2) 1. Write the NETFLIX/WMDRM key data on IC8401 mounted on the main PWB. 2.
LC-52/60/70LE640U,C6400U (1st Edition) [2] PUBLIC MODE SETTING PROCEDURE 1. How to start Public Mode • There are the following two ways to get the public mode setup screen displayed. In the adjustment process mode, turn on “PUBLIC MODE”. Also press the “CH ( power. )” and “VOL (+)” keys on the set at once and turn on the 1) Press the “INPUT” and “VOL (+)” keys on the set at once and turn on the power. 2) Get the password input screen displayed. Procedure ˴The input starts with the leftmost digit.
LC-52/60/70LE640U,C6400U (1st Edition) 4. Public Mode Menu The guidance is not displayed on screen. Setup procedure • To move the cursor up and down, use the “cursor UP/DOWN” key (remote controller) and “CH ( )/( )” key (remote controller and set). • To change the settings, use the “cursor RIGHT/LEFT” key (remote controller) and “VOL (+)/(–)” key (remote controller and set). • To save new settings, keep the cursor at “EXECUTE” and use “ENTER” key (remote controller and set).
LC-52/60/70LE640U,C6400U (1st Edition) 5. On Setting Items * “EZ-SETUP” discussed below indicates “EZ-SETUP after the first power-on”. 1) POWER ON FIXED Selection Default Explanation Limit in Setting Exception Remarks Selection between “Variable” and “Fixed” (loop provided) – (Variable) In “Fixed” setting, the power-off by the power key of the unit is invalidated and the image is kept being received. The power can be turned off by stopping the power supply from AC. Refer to the “Power-On Fixed” sheet.
LC-52/60/70LE640U,C6400U (1st Edition) 6) PANEL BUTTON Selection Default Explanation Limit in Setting Exception Selection between “Respond” and “No respond” (loop provided) Respond All the operations by keys (except the power key) of the unit can be invalidated. • Adjustment process, inspection mode and hotel menu mode can be started irrespective of setting. • All the keys can be used in adjustment process, inspection mode and hotel menu irrespective of setting.
LC-52/60/70LE640U,C6400U (1st Edition) 10)INPUT MODE FIXED Selection Default Explanation Limit in Setting Exception Remarks Selection between “Variable”, “Fixed”, “ACON (AC CTRL)” and “AC/RCON (AC/RC CTRL)” (loop provided) – (Variable) • At the “Fixed” setting, the TV set gets started with the settings of “Input mode start”, and then any other channels and inputs are not accepted. • At the “ACON (AC CTRL)” setting, the TV set gets started with the settings of “Input mode start” under AC control.
LC-52/60/70LE640U,C6400U (1st Edition) 15)PUBLIC MODE (ON/OFF) Selection Default Explanation Limit in Setting Exception Remarks Selection between “ON” and “OFF” (loop provided) OFF In case of “ON”, public mode settings are effected. None None The public-mode settings are operable only when this item is set at ON.
LC-52/60/70LE640U,C6400U (1st Edition) Service CHAPTER 6. TROUBLESHOOTING TABLE LC52LE640U Manual [1] Failure diagnosis by LED in front of cabinet START Is the Center Icon flashing? Yes Check "[2] LED flashing specification at the time of an error (Center icon LED used)". No No Is the Center Icon lighting When AC plug on? Check Power-Unit and AC-cable. Yes No Is the Backlight lighting? Check "LED Backlight does not turn on.". Yes Check "Picture does not display.".
LC-52/60/70LE640U,C6400U (1st Edition) Table 1. Concrete flashing pattern Detail display Item Inverter/Lamp system failure Power PWB failure (Power failure, etc.) Slow flashing Flashes once Flashes twice Main PWB failure (Communication failure, etc.
LC-52/60/70LE640U,C6400U (1st Edition) LED flashing timing chart at the time of an error 100ms 400ms 1.6sec 1) Inverter/Lamp failure details (Flashes slowly once and flashes fast) Error type Lamp failure Flashes fast once Center icon LED operation H: On L: Off 2) Power failure details (Flashes slowly twice and flashes fast) Error type PS_ON AC_DET failure Flashes fast once SM_POW Main 13V failure Flashes fast twice D_POW Digital 3.
LC-52/60/70LE640U,C6400U (1st Edition) 4) Other failure details (Flashes slowly 4 times and flashes fast) Error type Monitor temperature failure Flashes fast once Note Center icon LED operation H: On L: Off Main failure Flashes fast 3 times H: On L: Off 6–4 Pins are monitor microcomputer pins unless otherwise specified. If the panel temperature is 60°C or more for 15 seconds or more in a row, CAUTION appears on the OSD (flashes in red in the lower right screen).
LC-52/60/70LE640U,C6400U (1st Edition) [3] TROUBLESHOOTING TABLE • LED Backlight does not turn on. If it is not an error of power supply/LED driver, It is start-up in the lamp error disregard mode. Do you start? YES When main unit is replaced, does it start normally? YES Replace main unit. NO en LCD control unit is replaced, does it start normally? YES Replace LCD control unit. NO When the parts in the panel can be replaced. →Replace all LED-bars in the panel module.
LC-52/60/70LE640U,C6400U (1st Edition) Trouble Shooting Panel Module When C-S FPC is replaced, does screen display normally? YES Replace C-S FPC. NO When C-PWB is replaced, does screen display normally? YES Replace C-PWB. (Adjust “VCOM ADJ” after replace C-PWB) NO Replace Panel HIRAKI.
LC-52/60/70LE640U,C6400U (1st Edition) • Picture does not display. No video (1) COMPOSITE: No external input video [INPUT-6] COMPOSITE: No external input video [INPUT-7] Is INPUT-6 selected on the input select menu screen? Is INPUT-7 selected on the input select menu screen? NO Select INPUT-6 on the input select menu screen for the right input signal. NO Select INPUT-7 on the input select menu screen for the right input signal.
LC-52/60/70LE640U,C6400U (1st Edition) No video (2) COMPONENT: No external input video [INPUT-5] Is INPUT-5 selected on the input select menu screen? Is the INPUT-SELECT for the input signal? NO Select INPUT-5 on the input select menu screen for the right input signal. Does the COMP1_PLUG detection function? Check the line between pin (17) of input terminal (J510) and pin (L32) of IC3303 (CPU).
LC-52/60/70LE640U,C6400U (1st Edition) No video (3) No video at UHF/VHF broadcast signal reception No video at digital broadcast signal reception Is the specified TV signal selected on the input select menu screen? Is there the analog video signal output (CVBS) at pin (9) of tuner (TU1105)? Are there the IF signal outputs (D_IF+/-) at the pins (11) and (10) of tuner (TU1105)? NO Check TU1105 and its peripheral circuits (TU_SDATA: Pin4 of TU1105 TU_SCLK: Pin5 of TU1105, etc.).
LC-52/60/70LE640U,C6400U (1st Edition) No video (4) PC: No external input video [INPUT-8] Is INPUT-8 selected on the input select menu screen? NO Select INPUT-8 on the input select menu screen for the right input signal. YES Is IC1504 (HDMI switch) accessed by I2C, with PC connected, to read the VGA_SCL/SDA data? Check the DDC line and its peripheral circuits. (IC1504 and its peripherals).
LC-52/60/70LE640U,C6400U (1st Edition) No video (5)-1 HDMI: No external input video [INPUT-1] Is INPUT-1 selected on the input select menu screen? NO Select INPUT-1 on the input select menu screen for the right input signal.
LC-52/60/70LE640U,C6400U (1st Edition) No video (5)-2 HDMI: No external input video [INPUT-2] Is INPUT-2 selected on the input select menu screen? NO Select INPUT-2 on the input select menu screen for the right input signal.
LC-52/60/70LE640U,C6400U (1st Edition) No video (5)-3 HDMI: No external input video [INPUT-3] Is INPUT-3 selected on the input select menu screen? NO Select INPUT-3 on the input select menu screen for the right input signal.
LC-52/60/70LE640U,C6400U (1st Edition) No video (5)-4 HDMI: No external input video [INPUT-4] Is INPUT-4 selected on the input select menu screen? NO YES Does the HOT PLUG detection function? NO Does the DDC5V signal come from pin (18) of SC1505 to pin (51) of IC1504 (HDMI_SW)? YES Does the HPD signal come from pin (50) of IC1504 to pin (19) of SC1505? NO Select INPUT-4 on the input select menu screen for the right input signal.
LC-52/60/70LE640U,C6400U (1st Edition) • Does not sound. No audio (1) INPUT-6 No audio. INPUT-7 No audio. INPUT-5 No audio. Is INPUT-6 selected on the input select menu screen? Is INPUT-7 selected on the input select menu screen? Is INPUT-5 selected on the input select menu screen? NO Refer to “: No external input video [INPUT-6]”. NO Refer to “: No external input video [INPUT-7]”. NO Refer to “: No external input video [INPUT-5]”.
LC-52/60/70LE640U,C6400U (1st Edition) No audio (2) [PC analog audio input] INPUT-8 No audio. [HDMI analog audio input] INPUT-2 No audio. Is INPUT-8 selected on the input select menu screen? Is INPUT-2 selected on the input select menu screen? NO Refer to “: No external input video [INPUT-8]”. NO Refer to “: No external input video [INPUT-2]”.
LC-52/60/70LE640U,C6400U (1st Edition) No audio (3) No audio at UHF/VHF broadcast signal reception. No audio at digital broadcast signal reception. Is TV selected on the input select menu screen? Is TV selected on the input select menu screen? NO Refer to “No video at UHF/VHF broadcast signal reception”. NO Refer to “No video at digital broadcast signal reception”.
LC-52/60/70LE640U,C6400U (1st Edition) No audio (4) INPUT-1 No audio (HDMI connected) INPUT-2 No audio (HDMI connected) INPUT-3 No audio (HDMI connected) INPUT-4 No audio (HDMI connected) [INPUT-1 input] Is INPUT-1 selected on the input select menu screen? [INPUT-2 input] Is INPUT-2 selected on the input select menu screen? [INPUT-3 input] Is INPUT-3 selected on the input select menu screen? [INPUT-4 input] Is INPUT-4 selected on the input select menu screen? YES NO Refer to “: No external input video [
LC-52/60/70LE640U,C6400U (1st Edition) No audio signal at Digital Audio Output terminal (Analog sound heard) No INPUT-1/2/3/4 (HDMI) audio. No audio at digital broadcast signal reception. If no video appears, refer to “No external input video (HDMI) [INPUT-1/2/3/4]”. If no video appears, refer to “No video at digital broadcast signal reception”. Is there the SPDIF signal output (CPU_ASPDIF) at pin (AA31) of IC3303 (CPU)? NO Check the IC3303 and its peripheral circuits.
LC-52/60/70LE640U,C6400U (1st Edition) No monitor audio output Is the audio output from the monitor set at “VARIABLE” or “FIXED” on the menu screen? NO Check IC3303 (CPU) and its peripheral circuits. YES Are there the audio signal outputs at pins (AJ31) (HP_MON_L) and (AJ32) (HP_MON_R) of IC3303 (CPU)? NO Check IC3303 (CPU) and its peripheral circuits.
LC-52/60/70LE640U,C6400U (1st Edition) CHAPTER 7. MAJOR IC INFORMATIONS Service LC52LE640U Manual [1] MAJOR IC INFORMATIONS 1. MAJOR IC INFORMATIONS 1.1. IC1504 (VHiSii9387+-1Q) This IC is 5 input and 1 output HDMI port processor. The TMDS cores run at 2.25Gbps. (Supports video resolutions up to 1080p, 60Hz, 12bit.) The adaptive equalizer provides long cable support. This IC has been pre-programmed with HDCP keys. EDID and DDC support for 5 HDMI/DVI ports and 1 VGA port.
LC-52/60/70LE640U,C6400U (1st Edition) 1.11. IC9505 (VHiPD720114-1Q) This IC is a USB hub controller.
LC-52/60/70LE640U,C6400U (1st Edition) ― MEMO ― 7–3
LC-52/60/70LE640U,C6400U (1st Edition) CHAPTER 8.
LC-52/60/70LE640U,C6400U (1st Edition) [2] SYSTEM BLOCK DIAGRAM J CVBS2_IN CVBS INPUT 7 MAIN CVBS2_IN_L/R LR T-CON VBO_LOCKN CVBS1_IN CVBS LR L VBO_HTPDN PWM1 I2C_READY INPUT 5 PNL_EN LR COMP1_IN_L/R Component COMP1_Y/Pb/Pr N_PNL_EN PNL_WP I2C_0(400KHz) IC2601 Spliter HC2G66DP PNL_I2C_EN IIC2001 Reset UCOM_RST BU+3.
LC-52/60/70LE640U,C6400U (1st Edition) PartsGuide PARTS GUIDE No.
LC-52/60/70LE640U,C6400U (1st Edition) NO.
LC-52/60/70LE640U,C6400U (1st Edition) [4] CABINET PARTS (LC-60LE640U/C6400U) 24 19 16 16 60"LCD Panel Module Unit 25 D E 13 q s R/C OPC Unit j A 1-3 m 32 37 Wi-Fi Unit ICON Unit 1-2 B 30 p KEY Unit 1-7 5 38 B k 6 7 43 00 00 B 00 C 41 F h 34 00 11 00 00 A 00 27 00 1 43 n 00 B 1-1 9 39 10 00 1-8 17 43 20 23 22 r 8 D 3 43 3-1 3 15 3-1 3 43 3-1 43 s m j 2 43 l n 43 28 4 3 3-1 43 18 31 F 26 3-2 POWER/LED Drive Unit 21 i 2 3-2 E 2
LC-52/60/70LE640U,C6400U (1st Edition) NO.
LC-52/60/70LE640U,C6400U (1st Edition) [5] CABINET PARTS (LC-70LE640U/C6400U) 14 24 70"LCD Panel Module Unit 12 s R/C OPC Unit j A 1-3 41 D E m q 33 31 F h Wi-Fi Unit 36 18 ICON Unit 1-2 B 1-7 28 p 37 KEY Unit 6 18 B 7 k 8 41 1-4 B 2-3 1-5 C 1-6 2-2 A 1-5 2-4 40 11 9 B 1-1 38 42 n 26 10 1 16 1-8 41 21 20 19 r 25 17 D MAIN Unit 41 4-1 m 20 4 4-1 41 4-1 15 4 4-2 s 41 j 3 4-2 3 i l POWER/LED Drive Unit 17 30 41 4-1 42 29 5 4 E 41 41 n F
LC-52/60/70LE640U,C6400U (1st Edition) NO.
LC-52/60/70LE640U,C6400U (1st Edition) [6] SUPPLIED ACCESSORIES/PACKING PARTS (LC-52LE640U/C6400U) X1 X2 Stand Base Ass'y Stand Support Ass'y X8 Remote control unit X9 “AAA” size battery X6 Operation manual X3 Stand Screw Ass'y X7 Connection guide X4 Ennquete Card X5 Guarantee Card S3 X2 S5 X8 X9 S9 X3 S6 X4 X5 X6 X7 S8 S6 S6 S1 X1 S4 S7 S7 S7 S10 S2 7
LC-52/60/70LE640U,C6400U (1st Edition) NO.
LC-52/60/70LE640U,C6400U (1st Edition) [7] SUPPLIED ACCESSORIES/PACKING PARTS (LC-60LE640U/C6400U) X1 X2 Stand Base Ass'y Stand Support Ass'y X8 Remote control unit X9 “AAA” size battery X6 Operation manual X3 Stand Screw Ass'y X7 Connection guide X4 Ennquete Card X5 Guarantee Card S3 X2 S5 X8 X9 S9 X3 S6 X4 X5 X6 X7 S8 S6 S6 S1 X1 S4 S7 S7 S7 S10 S2 9
LC-52/60/70LE640U,C6400U (1st Edition) NO.
LC-52/60/70LE640U,C6400U (1st Edition) [8] SUPPLIED ACCESSORIES/PACKING PARTS (LC-70LE640U/C6400U) X S X8 Remote control unit pport Ass'y X9 “AA AAA” size battery X6 Operation manual X7 Connection guide X4 Ennquete Card X5 Guarantee Card 'y X2 S5 X8 S3 X9 S9 X3 S6 X4 X5 X6 X7 S8 S6 S6 S11 S12 S1 X1 S4 S7 S7 S7 S10 S2 11
LC-52/60/70LE640U,C6400U (1st Edition) NO.
LC-52/60/70LE640U,C6400U (1st Edition)
LC-52/60/70LE640U,C6400U (1st Edition) COPYRIGHT © 2012 BY SHARP CORPORATION ALL RIGHTS RESERVED. No Part of this publication may be reproduced, stored in a retrieval system, or transmitted in any from or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. Jan. 2012 SH.