HINA KS2 QSZZ AR-5316-5320-EX.
AR-5316-5320-EX.book 1 ページ 2005年4月8日 金曜日 午前9時35分 ➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣ FOR YOUR RECORDS ... To protect against loss or theft, record and retain for reference the copier’s serial number located on the back of the unit. Model Number Serial Number Date of Purchase Place of Purchase Authorized Sharp Copier Service Department Number ➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣ ➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣ ➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣ Do not make copies of anything which is prohibited from copying by law.
AR-5316-5320-EX.book 1 ページ 2005年4月8日 金曜日 午前9時35分 CONTENTS CAUTIONS................................................................................................................................................. 3 ● ● ● ● CAUTIONS ON USING..................................................................................................................................... 3 IMPORTANT POINTS WHEN SELECTING AN INSTALLATION SITE ...........................................................
!Chapter0.fm 2 ページ 6 2005年4月8日 金曜日 午前11時42分 ROUTINE MAINTENANCE CHECKING THE TOTAL OUTPUT COUNT AND TONER LEVEL........................................ 56 ● CHECKING THE TOTAL OUTPUT COUNT...56 CHECKING THE TONER LEVEL AND DRUM CARTRIDGE LIFE ........................................... 57 ● TONER LEVEL ...............................................57 ● DRUM CARTRIDGE LIFE ..............................57 ROUTINE MAINTENANCE..............................
AR-5316-5320-EX.book 3 ページ 2005年4月8日 金曜日 午前9時35分 CAUTIONS Follow the cautions below when using this machine. CAUTIONS ON USING Warning: • The fusing area is hot. Exercise care in this area when removing misfed paper. • Do not look directly at the light source. Doing so may damage your eyes. Caution: • Do not switch the machine rapidly on and off. After turning the machine off, wait 10 to 15 seconds before turning it back on. • Machine power must be turned off before installing any supplies.
AR-5316-5320-EX.book 4 ページ 2005年4月8日 金曜日 午前9時35分 The machine should be installed near an accessible power outlet for easy connection and disconnection. Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements. Also make certain the outlet is properly grounded. Note Connect the machine to a power outlet which is not used for other electric appliances. If a lighting fixture is connected to the same outlet, the light may flicker.
!Chapter0.fm 5 ページ 2005年5月12日 木曜日 午後7時14分 ENVIRONMENTAL INFORMATION As an ENERGY STAR® Partner, SHARP has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. The Environmental Choice Program guidelines are applied to the products only in Canada. The products that meet the Environmental Choice Program guidelines carry the logo shown to the left. The products without the logo may not meet the Environmental Choice Program guidelines.
AR-5316-5320-EX.book 6 ページ 2005年4月8日 金曜日 午前9時35分 CONVENTIONS USED IN THIS MANUAL Warning Warns the user that injury may result if the contents of the warning are not properly followed. Caution Cautions the user that damage to the machine or one of its components may result if the contents of the caution are not properly followed. Note Notes provide information relevant to the machine regarding specifications, functions, performance, operation and such, that may be useful to the user.
AR-5316-5320-EX.book 7 ページ 2005年4月8日 金曜日 午前9時35分 MAIN FEATURES High-speed laser copying • First-copy time*1 at 300 dpi*2 is only 7.2 seconds . • Copying speed is 16 copies per minute. This is ideal for business use and provides a big boost to workplace productivity. *1 First-Copy time may vary depending on the power-supply voltage, ambient temperature, and other operating conditions. *2 "dpi" ("dots per inch") is unit that is used to measure resolution.
!Chapter1.fm 8 ページ 2005年4月12日 火曜日 午後3時49分 Chapter 1 1 BEFORE USING THE MACHINE This chapter contains basic information that should be read before using the machine. PART NAMES AND FUNCTIONS 1 2 7 6 2 16 3 17 4 4 10 5 8 11 15 9 1 2 3 4 5 6 7 8 8 Glass cleaner Use to clean the original scanning glass. Document feeder cover (when the SPF is installed) /document cover Open to make copies from the document glass. (p.
AR-5316-5320-EX.book 9 ページ 2005年4月8日 金曜日 午前9時35分 BEFORE USING THE MACHINE 25 18 19 24 20 1 23 21 22 29 28 17 18 19 20 21 22 23 24 25 26 Parallel connector Connect to your computer to use the printer function. (Software Setup Guide) Document feeder tray (when the SPF is installed) Place the original(s) that you wish to scan face up here. Holds up to 40 originals. Original guides (when the SPF is installed) Adjust to the size of the originals.
AR-5316-5320-EX.book 10 ページ 2005年4月8日 金曜日 午前9時35分 BEFORE USING THE MACHINE OPERATION PANEL 1 2 3 XYZOOM ON LINE DUAL PAGE COPY 1 2 3 4 5 6 ON LINE key / indicator Press to toggle the machine between online and off-line. The indicator lights up when the machine is online, and goes off when the machine is off-line. The indicator blinks while the machine is receiving print data and while printing is paused. (p.
AR-5316-5320-EX.book 11 ページ 2005年4月8日 金曜日 午前9時35分 BEFORE USING THE MACHINE 4 6 5 AUDIT CLEAR AUTO TEXT PHOTO 7 POWER SAVE ORIGINAL PAPER SIZE SIZE 11X17 8½X14 8½X11 8½X5½ 8½X11 EXTRA ORIGINAL SIZE ENTER 14 10 ZOOM 11 12 25 400% INTERRUPT CLEAR 200% 141 129 121 100% 95 77 64 50% 1 3 5 13 9 8 START AUTO TRAY SELECT IMAGE PRESET RATIO 15 16 17 18 19 20 1 CLEAR ALL 21 23 22 24 25 26 Not used for this machine.
AR-5316-5320-EX.book 12 ページ 2005年4月8日 金曜日 午前9時35分 POWER ON AND OFF The power switch is located on the left side of the machine. POWER ON POWER OFF Turn the power switch to the "ON" position. Make sure that the machine is not in operation and then turn the power switch to the "OFF" position. It will take about 45 seconds for the machine to warm up. While the machine is warming up, the POWER SAVE indicator will blink. (The POWER SAVE indicator will go off when the machine is ready to copy.
AR-5316-5320-EX.book 13 ページ 2005年4月8日 金曜日 午前9時35分 LOADING PAPER The paper required indicator ( ) will light up when there is no copy paper in the selected paper feed tray, or when the selected paper tray is not installed or is improperly installed. PAPER For best results, use only SHARP recommended paper.
AR-5316-5320-EX.book 14 ページ 2005年4月8日 金曜日 午前9時35分 BEFORE USING THE MACHINE LOADING PAPER Make sure that the machine is not copying or printing, and then follow these steps to load paper. Loading the paper tray 1 Gently lift and pull out the paper tray until it stops. 5 Gently push the paper tray into the machine. 15 2 Push the pressure plate down until it locks in place. Push the center of the pressure plate down until it locks into place. 3 Fan the paper.
AR-5316-5320-EX.book 15 ページ 2005年4月8日 金曜日 午前9時35分 BEFORE USING THE MACHINE Loading the bypass tray 1 Unfold the bypass tray. 3 Insert the paper (print face down) all the way into the bypass tray. To prevent a misfeed, verify once more that the paper guides are adjusted to the width of the paper. When feeding large paper such as 8-1/2" x 14" and 11" x 17", pull out the bypass tray extension. 2 Note If you loaded paper in the bypass tray, press the [TRAY SELECT] key ( ) to select the bypass tray.
AR-5316-5320-EX.book 16 ページ 2005年4月8日 金曜日 午前9時35分 BEFORE USING THE MACHINE Envelopes Do not use the following envelopes, as misfeeds will occur. • Envelopes with metal tabs, clasps, strings, holes, or windows. • Envelopes with rough fibers, carbon paper, or glossy surfaces. • Envelopes with two or more flaps. • Envelopes with tape, film, or paper attached to the flap. • Envelopes with a fold in the flap. • Envelopes with glue on the flap to be moistened for sealing. • Envelopes with labels or stamps.
AR-5316-5320-EX.book 17 ページ 2005年4月8日 金曜日 午前9時35分 BEFORE USING THE MACHINE 4 Press the [START] key ( ) and then the [PAPER SIZE ENTER] key. START Note To change the paper size setting of another tray, repeat steps 2 to 5 after pressing the [START] key ( ). 1 Affix the paper size label for the paper size selected in step 3 to the label position on the right end of the tray.
AR-5316-5320-EX.book 18 ページ 2 2005年4月8日 金曜日 午前9時35分 Chapter 2 COPY FUNCTIONS This chapter explains basic copying functions such as normal copying, reduction or enlargement, and exposure adjustment. NORMAL COPYING This section explains how to make a regular copy. If "Auditing mode" has been enabled (p.39), enter your 3-digit account number. Copying from the document glass 1 Open the document cover/SPF, and place the original. 3 Press the [ORIGINAL SIZE ENTER] key and select the original size.
!Chapter2.fm 19 ページ 2005年4月8日 金曜日 午後1時15分 COPY FUNCTIONS Copying from the SPF 1 2 Make sure that an original has not been left on the document glass. Close the SPF. Adjust the original guides to the size of the original(s). 5 Press the [START] key ( copying. START Note 3 Set the original(s) face up in the document feeder tray. ) to begin The copy is delivered to the paper output tray. • The paper output tray can hold up to 250 sheets of paper.
!Chapter2.fm 20 ページ 2005年4月8日 金曜日 午後2時0分 COPY FUNCTIONS Removing the document cover Originals that can be used in the SPF To copy large originals like newspapers, remove the document cover. To remove the cover, lift straight up as shown. To replace the cover, do the reverse. The SPF cannot be removed. Originals that are 5-1/2" x 8-1/2" to 11" x 17" and 15 lbs. to 24 lbs. (56 g/m2 to 90 g/m2) can be used. A maximum of 40 pages can be placed at once.
AR-5316-5320-EX.book 21 ページ 2005年4月8日 金曜日 午前9時35分 COPY FUNCTIONS MAKING A COPY DARKER OR LIGHTER Automatic exposure adjustment is initially enabled. This function automatically adjusts the copy image according to the original being copied. If you wish to select the exposure level yourself, follow the steps below. (Select from two original types and five exposure levels for each original type.) The exposure level used in automatic exposure adjustment can also be changed.
AR-5316-5320-EX.book 22 ページ 2005年4月8日 金曜日 午前9時35分 COPY FUNCTIONS SETTING THE NUMBER OF COPIES Press the numeric keys to set the number of copies. Important note when making a large number of copies ● The set number of copies appears in the display. A maximum of 999 copies (factory default setting) can be set. ● If you wish to make only a single copy, copying is possible with the display showing "0". Note The maximum number of copies can be changed in the user programs. (p.
AR-5316-5320-EX.book 23 ページ 2005年4月8日 金曜日 午前9時35分 COPY FUNCTIONS 4 5 Press the [AUTO IMAGE] key. The AUTO IMAGE indicator lights up and the appropriate ratio for the original size and paper size is selected. (The indicator of the selected ratio will light up.) AUTO IMAGE Set the number of copies and other copy settings, and then press the [START] key ( ). The copy will be delivered to the paper output tray. Note To cancel automatic ratio selection, press the [AUTO IMAGE] key again.
AR-5316-5320-EX.book 24 ページ 2005年4月8日 金曜日 午前9時35分 COPY FUNCTIONS SELECTING THE VERTICAL AND HORIZONTAL COPY RATIOS SEPARATELY (XY ZOOM copying) The XY ZOOM feature allows the horizontal and vertical copy ratios to be changed independently. Example: Reduction only in the horizontal direction. Original Note Copy • To use the XY ZOOM feature with the DUAL PAGE COPY feature, set the DUAL PAGE COPY feature first and then the XY ZOOM feature.
!Chapter2.fm 25 ページ 2005年4月8日 金曜日 午後3時38分 COPY FUNCTIONS 6 Use the [PRESET RATIO] selector keys ( , ) and [Zoom] keys ( , to change the copy ratio in the horizontal direction. ) Press the [PRESET RATIO] selector keys ( , ) to select a ratio close to the desired ratio, and then press the [Zoom] keys ( , ) to adjust the ratio in increments of 1%. The ratio appears in the display. 7 Press the [Copy ratio display] key ( ).
AR-5316-5320-EX.book 26 ページ 2005年4月8日 金曜日 午前9時35分 TWO-SIDED COPYING USING THE BYPASS TRAY To perform manual two-sided copying, follow these steps. Example: Copying originals A and B onto each side of one sheet of paper 1 2 1 Copy Original A Original B 1 3 Copy original A. Turn the copy of original A over, and without changing the position of the edge closest to you, insert it in the bypass tray. Insert the paper all the way in.
AR-5316-5320-EX.book 27 ページ 2005年4月8日 金曜日 午前9時35分 DUAL PAGE COPYING A dual page original can be automatically separated into two pages during copying. This feature is convenient for making copies of books and other dual page originals on individual sheets of paper. Original Note 1 • • • • • Copy 8-1/2" x 11" paper is used for dual page copying. When used in combination with XY ZOOM copying, enlargement is not possible. Dual page copying cannot be used in combination with the enlargement copying.
AR-5316-5320-EX.book 28 ページ 2005年4月8日 金曜日 午前9時35分 INTERRUPTING A COPY RUN (Interrupt copying) A copy run can be temporarily interrupted to allow another copy job to be performed. When the other job is finished, the copy run will resume using the original copy settings. Note 1 Interrupt copying is not possible when the user programs are being configured. Press the [INTERRUPT] key ( interrupt the copy run.
AR-5316-5320-EX.book 29 ページ 2005年4月8日 金曜日 午前9時35分 Chapter 3 3 PRINTER FUNCTIONS The machine includes a USB 1.1 connector and a parallel connector as standard equipment. A computer can be connected to these connectors to use the machine as a printer. To use the machine as a printer, the printer driver must first be installed as explained in the "Software Setup Guide". Note • If a problem occurs in printer mode, see "TROUBLESHOOTING" (p.40).
AR-5316-5320-EX.book 30 ページ 2005年4月8日 金曜日 午前9時35分 PRINTER FUNCTIONS Pausing a print job To pause a print job during printing, press the [ON LINE] key on the operation panel to switch the machine off-line. Printing will be paused and the ON LINE indicator will blink. To cancel a print job, press the [CLEAR] key ( ) or the [CLEAR ALL] key ( ). To resume printing, press the [ON LINE] key to switch the machine online.
AR-5316-5320-EX.book 31 ページ 4 2005年4月8日 金曜日 午前9時35分 Chapter 4 USER SETTINGS This chapter explains how to set the automatic exposure level, toner save mode/high image quality mode, and the user programs, which are custom settings that control fine points of the machine’s operation. ADJUSTING THE AUTOMATIC EXPOSURE LEVEL The exposure level used in automatic exposure adjustment, which automatically adjusts the copy exposure according to the original, can be adjusted.
AR-5316-5320-EX.book 32 ページ 2005年4月8日 金曜日 午前9時35分 TONER SAVE MODE AND HIGH IMAGE QUALITY MODE Toner save mode can be enabled to reduce toner consumption by about 10%. The high image quality mode improves copy image quality in the automatic and manual exposure modes by increasing copy density with a slight increase of toner consumption. To switch between toner save mode and high image quality mode, follow the steps below. 1 Press the [AUTO/TEXT/PHOTO] key to select "TEXT".
AR-5316-5320-EX.book 33 ページ 2005年4月8日 金曜日 午前9時35分 CUSTOMIZING SETTINGS (User programs) The user programs allow you to customize the machine to match your needs. USER PROGRAMS Program number 1 2 Program name Auto clear time Preheat mode Setting codes (factory default setting appears in bold) 1: OFF 2: 10 sec. 3: 20 sec. 4: 60 sec. 5: 90 sec. 6: 120 sec. 1: 1 min. 2: 5 min. 3: 30 min. 4: 60 min. 5: 120 min. 6: 240 min. 3 Auto power shut-off timer 1: 5 min. 2: 30 min. 3: 60 min. 4: 120 min.
AR-5316-5320-EX.book 34 ページ 2005年4月8日 金曜日 午前9時35分 USER SETTINGS Program number Setting codes (factory default setting appears in bold) 23 Resolution in Auto/Text mode 1: 300 dpi 2: 600 dpi 25 Key auto repeat 0: OFF 1: ON 26 27 28 29 34 Program name 1: Minimum (current response speed) Key press time 2: 0.5 sec. 3: 1.0 sec. 4: 1.5 sec. 5: 2.0 sec.
AR-5316-5320-EX.book 35 ページ 2005年4月8日 金曜日 午前9時35分 USER SETTINGS SELECTING A SETTING FOR A USER PROGRAM 1 Hold down the [Light] key ( the alarm indicators ( , , blink. ) until , , ) 4 Enter the desired setting code by pressing a numeric key. • For the setting codes, see "USER PROGRAMS". (p.33 to p.34) • The selected setting code blinks. • For example, to select 90 seconds, press the [5] key. The display shows "- -" with the left hyphen blinking.
AR-5316-5320-EX.book 36 ページ 2005年4月8日 金曜日 午前9時35分 SETTINGS FOR AUDITING MODE AUDITING MODE When "Auditing mode" is enabled, a count is kept of the number of copies made by each account (up to 20 accounts can be established), and the counts can be displayed and totaled as necessary. In "Auditing mode", the display shows "- - -", and this indicates that a 3-digit account number must be entered in order to use the machine for copying.
AR-5316-5320-EX.book 37 ページ 2005年4月8日 金曜日 午前9時35分 USER SETTINGS SELECTING AUDITING MODE SETTINGS 1 Hold down the [Light] key ( the alarm indicators ( , , blink. ) until , , ) The display shows "- -" with the left hyphen blinking. 5 Press the [Light] key ( ) to complete the settings. The alarm indicators ( , , , , ) go off and the display returns to the number of copies display. 1 3 5 2 Enter the program number with the numeric keys.
AR-5316-5320-EX.book 38 ページ 2005年4月8日 金曜日 午前9時35分 USER SETTINGS Auditing mode Account number deletion (program No.10) (program No.13) 1 Press the [1] key to enable "Auditing mode" or the [0] key to disable it, and then press the [START] key ( ). Use this procedure to delete account numbers. A single account number can be deleted, or all account numbers at once. If no account numbers have been established, the error code "13E" will appear in the display.
AR-5316-5320-EX.book 39 ページ 2005年4月8日 金曜日 午前9時35分 USER SETTINGS Resetting account (program No.15) The copy count of a single account or all accounts can be reset to 0. If no account numbers have been established, the error code "15E" will appear in the display. Copying when "Auditing mode" is enabled When "Auditing mode" is enabled, "- - -" appears in the display. [Resetting all accounts] Press the [1] key and then press the [START] key ( ). The copy counts of all accounts will be deleted.
AR-5316-5320-EX.book 40 ページ 5 2005年4月8日 金曜日 午前9時35分 Chapter 5 TROUBLESHOOTING This chapter describes troubleshooting and misfeed removal. TROUBLESHOOTING If you experience difficulty using the machine, check the following troubleshooting guide before calling for service. Many problems can be easily resolved by the user. If you are unable to solve the problem using the troubleshooting guide, turn off the power switch and unplug the machine, and contact your SHARP service center.
AR-5316-5320-EX.book 41 ページ 2005年4月8日 金曜日 午前9時35分 TROUBLESHOOTING MACHINE/COPYING PROBLEMS The following problems are related to the general operation of the machine and copying. Problem Cause and solution The machine is not plugged into a power outlet. → Plug the machine into a grounded outlet. Power switch OFF. → Turn the power switch ON. Page – 12 The POWER SAVE indicator is blinking. → Indicates that the machine is warming up. Copies cannot be made until the machine has finished warming up.
AR-5316-5320-EX.book 42 ページ 2005年4月8日 金曜日 午前9時35分 TROUBLESHOOTING Problem Cause and solution Misfeed occurs. → To remove the misfeed, see "MISFEED REMOVAL". The paper is outside of the specified size and weight range. Page 47 13 → Use copy paper within the specified range. Paper curled or damp. → Do not use curled or crimped paper. Replace with dry copy paper.
AR-5316-5320-EX.book 43 ページ 2005年4月8日 金曜日 午前9時35分 TROUBLESHOOTING Problem Cause and solution The document glass or the underside of the document cover/SPF is dirty. Copies are smudged or dirty. Original smudged or blotchy. The scanner glass in the SPF is dirty. → Clean the long, narrow glass in the SPF. The transfer charger is dirty. → Clean the transfer charger. Copying or printing is performed. → Set the paper size after copying is complete. Paper size for a paper tray cannot be set.
!Chapter4.fm 44 ページ 2005年4月11日 月曜日 午前9時18分 TROUBLESHOOTING PRINTING PROBLEMS In addition to this section, troubleshooting information can also be found in the README files for each of the software programs. To view a README file, see the "Software Setup Guide". Problem Cause and solution The machine is set to off-line mode. → Press the [ON LINE] key to turn on the ON LINE indicator. Page 29 The machine is not correctly connected with your computer.
AR-5316-5320-EX.book 45 ページ 2005年4月8日 金曜日 午前9時35分 TROUBLESHOOTING Problem Printing is slow. Cause and solution Simultaneous use of two or more application software programs. Page – → Start printing after quitting all unused application software programs. The printed image is light and uneven. The paper is loaded so that printing takes place on the back side of the paper. → Some paper types have a front and back side.
AR-5316-5320-EX.book 46 ページ 2005年4月8日 金曜日 午前9時35分 INDICATORS AND DISPLAY MESSAGES If one of the following indicators lights up or one of the following messages appears in the display, check the meaning of the indicator or message in the following table and take appropriate action.
AR-5316-5320-EX.book 47 ページ 2005年4月8日 金曜日 午前9時35分 MISFEED REMOVAL When a misfeed occurs, the misfeed indicator ( ) and a misfeed location indicator ( ) will blink and the machine will automatically stop. Check the blinking misfeed location indicator to identify the location of the misfeed and remove it. Note The paper may tear when you remove a misfeed. In this event, be sure to remove all torn pieces of paper from the machine, taking care not to touch the drum cartridge (the green part).
AR-5316-5320-EX.book 48 ページ 2005年4月8日 金曜日 午前9時35分 TROUBLESHOOTING Section C Remove the misfed original from the exit area. 2 Open and close the SPF to make the misfeed location indicator stop blinking. You can also make the misfeed indicator stop blinking by opening and closing the feeding roller cover or the right side cover. If the misfed original cannot be easily removed from the exit area, open the moveable part of the document feeder tray and remove the original.
AR-5316-5320-EX.book 49 ページ 2005年4月8日 金曜日 午前9時35分 TROUBLESHOOTING MISFEED IN THE MACHINE 1 Open the bypass tray and the side cover. 2 Check the misfeed location. Remove the misfed paper following the instructions for each location in the illustration below. If paper is misfed here, go to "B. Misfeed in the fusing area". If the misfed paper is visible here, go to "C. Misfeed in the transport area". If paper is misfed here, go to "A. Misfeed in the paper feed area". A.
AR-5316-5320-EX.book 50 ページ 2005年4月8日 金曜日 午前9時35分 TROUBLESHOOTING B. Misfeed in the fusing area 1 Push gently on both ends of the front cover. 2 Turn the roller rotating knob in the direction of the arrow. 4 Lift the fusing unit release levers, to return them to their operating positions. 5 Close the front cover and side cover. Roller rotating knob 3 The misfeed indicator ( ) will go out. Carefully remove the misfed paper. Lower the fusing unit release levers to allow easier removal.
AR-5316-5320-EX.book 51 ページ 2005年4月8日 金曜日 午前9時35分 TROUBLESHOOTING C. Misfeed in the transport area 1 Open the fusing paper guide by pressing down the projection on either side of the guide and remove the misfed paper. Be careful not to tear the misfed paper during removal. The fusing unit is hot. Do not touch Warning the fusing unit when removing misfed paper. Doing so may cause a burn or injury.
AR-5316-5320-EX.book 52 ページ 2005年4月8日 金曜日 午前9時35分 TROUBLESHOOTING MISFEED IN THE PAPER TRAY Note 1 Make sure that there is no misfed paper in the tray before pulling it out. (p.49) Lift and pull out the paper tray and remove the misfed paper. Be careful not to tear the misfed paper during removal. 2 Open and close the side cover. The misfeed indicator ( ) will go out. Note 3 • When closing the side cover, press on the handle.
AR-5316-5320-EX.book 53 ページ 2005年4月8日 金曜日 午前9時35分 REPLACING THE TD CARTRIDGE When the TD cartridge replacement required indicator ( ) lights up, the TD cartridge will need replacement soon. Obtain a new cartridge. When the TD cartridge replacement required indicator ( ) blinks, the TD cartridge must be replaced before copying can be resumed. Replace the TD cartridge by following the procedure below.
AR-5316-5320-EX.book 54 ページ 2005年4月8日 金曜日 午前9時35分 TROUBLESHOOTING 6 Close the front cover. Note The TD cartridge replacement required indicator ( ) will go out. • Before closing the front cover, make sure that the TD cartridge is correctly installed. • When closing the front cover, gently hold both ends. REPLACING THE DRUM CARTRIDGE The useful life of the drum cartridge is approximately 30,000 copies.
AR-5316-5320-EX.book 55 ページ 2005年4月8日 金曜日 午前9時35分 TROUBLESHOOTING 5 Remove the new drum cartridge from the protective bag and gently insert the lead end of the drum cartridge along the guides. Do not touch the drum cartridge (green Caution portion). Doing so may damage the drum and cause smudges on copies. 6 Remove the protective cover from the drum cartridge and then push the cartridge all the way into the machine. 1 2 7 5 Insert the TD cartridge along the guides until it locks in place.
AR-5316-5320-EX.book 56 ページ 6 2005年4月8日 金曜日 午前9時35分 Chapter 6 ROUTINE MAINTENANCE This chapter explains how to keep the machine operating smoothly, including viewing copy count, the toner level indicator, and cleaning the machine. CHECKING THE TOTAL OUTPUT COUNT AND TONER LEVEL CHECKING THE TOTAL OUTPUT COUNT From the "0" display, you can check the total output count, total copy count, as explained below.
AR-5316-5320-EX.book 57 ページ 2005年4月8日 金曜日 午前9時35分 CHECKING THE TONER LEVEL AND DRUM CARTRIDGE LIFE TONER LEVEL DRUM CARTRIDGE LIFE The toner level is indicated by a 6-level display. Use it as a guideline for replacing the TD cartridge. To find out how many more copies can be made before the 30,000 mark is reached, follow the procedure described below. 1 Hold down the [Light] key ( the alarm indicators ( , , blink. ) until , , ) 1 The display will show "- -".
!Chapter5.fm 58 ページ 2005年4月8日 金曜日 午後1時11分 ROUTINE MAINTENANCE CLEANING THE DOCUMENT GLASS AND SPF/ DOCUMENT COVER If the document glass, SPF, underside of the document cover, or the scanner for originals coming from the SPF (the long narrow glass surface on the right side of the document glass) become dirty, the dirt may appear on copies. Always keep these parts clean. Stains or dirt on the document glass/SPF will also be copied.
!Chapter5.fm 59 ページ 2005年4月8日 金曜日 午前11時14分 ROUTINE MAINTENANCE CLEANING THE BYPASS TRAY PAPER FEED ROLLER If misfeeds occur frequently when feeding envelopes, thick paper, etc. through the bypass tray, wipe the paper feed roller at the feed slot of the bypass tray with a soft, clean cloth dampened with alcohol or water. Paper feed roller CLEANING THE TRANSFER CHARGER If copies start becoming streaky or blotchy, the transfer charger may be dirty. Clean the charger using the following procedure.
!Chapter6.fm 60 ページ 2005年4月8日 金曜日 午後1時27分 Chapter 7 7 PERIPHERAL DEVICES AND SUPPLIES Optional equipment and supplies are explained in this chapter. To purchase optional equipment and supplies, contact SHARP service. PERIPHERAL DEVICES Note As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units.
AR-5316-5320-EX.book 61 ページ 2005年4月8日 金曜日 午前9時35分 STORAGE OF SUPPLIES Standard supplies for this product that are to be replaced by the user are paper and TD cartridge. For best copying results, be sure to use only SHARP Genuine Supplies which are designed, engineered and tested to maximize the life and performance of SHARP copiers. Look for the Genuine Supplies label on the toner package.
AR-5316-5320-EX.book 62 ページ 8 2005年4月8日 金曜日 午前9時35分 Chapter 8 APPENDIX SPECIFICATIONS Type Digital Multifunctional System, Desktop Photoconductive type OPC drum Document glass type Fixed Copy system Dry, electrostatic transfer Originals Sheets, bound documents Original sizes Max. 11" x 17" Copy size Max. 11" x 17" Min. 5-1/2" x 8-1/2" (must be fed from the bypass tray) Image loss: Max. 5/32" (4 mm) (leading and trailing edges) Max.
!Chapter7.fm 63 ページ 2005年4月11日 月曜日 午前11時22分 APPENDIX Weight Approx. 69.1 lbs. (31.3 kg) (Not including TD cartridge) Dimensions 23-15/64" (W) x 22-23/32" (D) x 18-33/64" (H) (590 mm (W) x 577 mm (D) x470 mm (H)) Operating conditions Temperature: 59°F to 86°F (15°C to 30°C), Humidity: 20% to 85% Noise level Sound Power Level LwA(1B=10dB) Copying: 6.2[B] Standby: 3.
AR-5316-5320-EX.book 64 ページ 2005年4月8日 金曜日 午前9時35分 SOFTWARE LICENSE PLEASE READ THIS LICENSE CAREFULLY BEFORE USING THE SOFTWARE. BY USING THE SOFTWARE, YOU ARE AGREEING TO BE BOUND BY THE TERMS OF THIS LICENSE. 1. License. The application, demonstration, system and other software accompanying this License, whether on disk, in read only memory, or on any other media (the "Software") and related documentation are licensed to you by SHARP.
AR-5316-5320-EX.book 65 ページ 2005年4月8日 金曜日 午前9時35分 6. Limited Warranty on Media. SHARP warrants the disks on which the Software is recorded to be free from defects in materials and workmanship under normal use for a period of ninety (90) days from the date of purchase as evidenced by a copy of the receipt. The entire liability of SHARP and/or its Licensors and your exclusive remedy will be replacement of the disk which fails to meet the limited warranty provided by this Clause 6.
AR-5316-5320-EX.book 66 ページ 2005年4月8日 金曜日 午前9時35分 MATERIAL SAFETY DATA SHEET Page : 1/4 Date Issued : Jun. 1, 2005 MSDS No. F-01381 1.PRODUCT AND COMPANY IDENTIFICATION : AR-016TD (Black Toner) Product Name : Sharp Corporation 22-22 Nagaike-cho, Abeno-ku, Osaka, Japan Local suppliers are listed below. Please contact the nearest supplier for additional information. Area (Country) (Name and Telephone Number) U.S.A.
AR-5316-5320-EX.book 67 ページ 2005年4月8日 金曜日 午前9時35分 MATERIAL SAFETY DATA SHEET Page : 2/4 Date Issued : Jun. 1, 2005 MSDS No. F-01381 3.HAZARDS IDENTIFICATION Most Important Hazards and Effects of the Products Human Health Effects : There are no anticipated carcinogenic effects from exposure based on animal tests performed using toner. When used as intended according to instructions, studies do not indicate any symptoms of fibrosis will occur. Environmental Effects : No data are available.
AR-5316-5320-EX.book 68 ページ 2005年4月8日 金曜日 午前9時35分 MATERIAL SAFETY DATA SHEET Page : 3/4 Date Issued : Jun. 1, 2005 MSDS No. F-01381 Exposure Limit Values OSHA-PEL(USA) ACGIH-TLV(USA) Personal Protective Equipment Respiratory Protection Hand Protection Eye Protection Skin Protection Other Protective Equipment 3 : 15mg/m (Total Dust), 3 : 10mg/m (Total Dust), 3 5mg/m (Respirable Dust) 3 3mg/m (Respirable Dust) : Not required under intended use. : Not required under intended use.
AR-5316-5320-EX.book 69 ページ 2005年4月8日 金曜日 午前9時35分 MATERIAL SAFETY DATA SHEET Chronic Effect Page : 4/4 Date Issued : Jun. 1, 2005 MSDS No.
AR-5316-5320-EX.book 70 ページ 2005年4月8日 金曜日 午前9時35分 MATERIAL SAFETY DATA SHEET Page : 1/4 Date Issued : Jun. 1, 2005 MSDS No. F-31381 1.PRODUCT AND COMPANY IDENTIFICATION Product Name : AR-016TD (Black Developer) Supplier Identification : Sharp Corporation 22-22 Nagaike-cho, Abeno-ku, Osaka, Japan Local suppliers are listed below. Please contact the nearest supplier for additional information. Area (Country) (Name and Telephone Number) U.S.A.
AR-5316-5320-EX.book 71 ページ 2005年4月8日 金曜日 午前9時35分 MATERIAL SAFETY DATA SHEET Page : 2/4 Date Issued : Jun. 1, 2005 MSDS No. F-31381 3.HAZARDS IDENTIFICATION Most Important Hazards and Effects of the Products Human Health Effects : There are no anticipated carcinogenic effects from exposure based on animal tests performed using toner. When used as intended according to instructions, studies do not indicate any symptoms of fibrosis will occur. Environmental Effects : No data are available.
AR-5316-5320-EX.book 72 ページ 2005年4月8日 金曜日 午前9時35分 MATERIAL SAFETY DATA SHEET Page : 3/4 Date Issued : Jun. 1, 2005 MSDS No. F-31381 Exposure Limit Values OSHA-PEL(USA) ACGIH-TLV(USA) Personal Protective Equipment Respiratory Protection Hand Protection Eye Protection Skin Protection Other Protective Equipment 3 : 15mg/m (Total Dust), 3 : 10mg/m (Total Dust), 3 5mg/m (Respirable Dust) 3 3mg/m (Respirable Dust) : Not required under intended use. : Not required under intended use.
AR-5316-5320-EX.book 73 ページ 2005年4月8日 金曜日 午前9時35分 MATERIAL SAFETY DATA SHEET Chronic Effect Page : 4/4 Date Issued : Jun. 1, 2005 MSDS No.
AR-5316-5320-EX.book 74 ページ 2005年4月8日 金曜日 午前9時35分 INDEX Symbols [ ] key..........................................................11, 56 A About the operation manuals - Online Manual.....................................................5 - Operation Manual ...............................................5 - Software Setup Guide.........................................5 Adjusting the automatic exposure level....................31 Alarm indicators .........................10, 35, 37, 43, 45, 46 Appendix ....
AR-5316-5320-EX.book 75 ページ 2005年4月8日 金曜日 午前9時35分 O ON LINE indicator ..............................................10, 29 ON LINE key ......................................................10, 29 Operation in copy and printer modes .......................30 Operation panel....................................................8, 10 Original guides .....................................................9, 19 ORIGINAL SIZE ENTER key .......................10, 16, 18 ORIGINAL SIZE indicator ....................
AR-5316-5320-EX.book 76 ページ 2005年4月8日 金曜日 午前9時35分 INDEX BY PURPOSE Copying Automatic ratio selection ..........................................22 Canceling a copy run .........................................18, 19 Copying, starting ................................................18, 19 Dual page copying .................................................. 27 Enlargement/reduction ............................................ 22 Exposure adjustment ..............................................
AR-5316-5320-EX.book 1 ページ 2005年4月8日 金曜日 午前9時35分 For users in the USA This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Cover4.fm 1 ページ 2005年5月20日 金曜日 午前11時11分 AR-5316 SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430-1163. www.sharp-usa.com SHARP ELECTRONICS OF CANADA LTD. 335 Britannia Road East, Mississauga, Ontario, L4Z 1W9 SHARP CORPORATION This manual has been printed using a vegetable-based soy oil ink to help protect the environment.