HINA KS➀ QSZZ AR-5316-5320-EX.
AR-5316-5320-EX.book 1 ページ ２００３年１１月２６日 水曜日 午後５時３分 Do not make copies of anything which is prohibited from copying by law. The following items are normally prohibited from copying by national law. Other items may be prohibited by local law. ● Money ● Stamps ● Bonds ● Stocks ● Checks ● Passports ● Driver's licenses ● Bank drafts In some areas, the "POWER" switch positions are marked "I" and " " on the copier instead of "ON" and "OFF".
AR-5316-5320-EX.book 1 ページ ２００３年１１月２６日 水曜日 午後５時３分 CONTENTS CAUTIONS................................................................................................................................................. 3 ● ● ● ● ● CAUTIONS ON USING..................................................................................................................................... 3 IMPORTANT POINTS WHEN SELECTING AN INSTALLATION SITE ...........................................................
AR-5316-5320-EX.book 2 ページ 6 ２００３年１１月２６日 水曜日 午後５時３分 ROUTINE MAINTENANCE CHECKING THE TOTAL OUTPUT COUNT AND TONER LEVEL........................................ 55 ● CHECKING THE TOTAL OUTPUT COUNT...55 ● CHECKING THE TONER LEVEL ...................56 ROUTINE MAINTENANCE.............................. 56 ● CLEANING THE DOCUMENT GLASS AND SPF/DOCUMENT COVER .............................56 ● CLEANING THE BYPASS TRAY PAPER FEED ROLLER ...............................................
AR-5316-5320-EX.book 3 ページ ２００３年１１月２６日 水曜日 午後５時３分 CAUTIONS Follow the cautions below when using this machine. CAUTIONS ON USING Warning: • The fusing area is hot. Exercise care in this area when removing misfed paper. • Do not look directly at the light source. Doing so may damage your eyes. Caution: • Do not switch the machine rapidly on and off. After turning the machine off, wait 10 to 15 seconds before turning it back on. • Machine power must be turned off before installing any supplies.
AR-5316-5320-EX.book 4 ページ ２００３年１１月２６日 水曜日 午後５時３分 The machine should be installed near an accessible power outlet for easy connection and disconnection. Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements. Also make certain the outlet is properly grounded. Note Connect the machine to a power outlet which is not used for other electric appliances. If a lighting fixture is connected to the same outlet, the light may flicker.
AR-5316-5320-EX.book 5 ページ ２００３年１１月２６日 水曜日 午後５時３分 USING THE MANUAL This machine has been designed to provide convenient copying features in a minimum amount of office space and with maximum operational ease. To get full use of all machine features, be sure to familiarise yourself with this manual and the machine. For quick reference during machine use, keep this manual in a handy location.
AR-5316-5320-EX.book 6 ページ ２００３年１１月２６日 水曜日 午後５時３分 DIFFERENCES BETWEEN MODELS This manual covers the following models. Model AR-5320/AR-5320 X AR-5316/AR-5316 X (With optional SPF installed) (With optional SPF installed) Appearance The above illustration is used in instances where a function and/ or the operation of the machine is the same on both models.
AR-5316-5320-EX.book 7 ページ ２００３年１１月２６日 水曜日 午後５時３分 MAIN FEATURES High-speed laser copying • First-copy time*1 at 300 dpi*2 is only 7.2 seconds . • Copying speed is 20/16 copies per minute. This is ideal for business use and provides a big boost to workplace productivity. *1 First-Copy time may vary depending on the power-supply voltage, ambient temperature, and other operating conditions. *2 "dpi" ("dots per inch") is unit that is used to measure resolution.
AR-5316-5320-EX.book 8 ページ ２００３年１１月２６日 水曜日 午後５時３分 Chapter 1 1 BEFORE USING THE MACHINE This chapter contains basic information that should be read before using the machine. PART NAMES AND FUNCTIONS 1 1 15 2 16 3 6 5 3 9 4 7 10 14 8 1 2 3 4 5 6 7 8 Document feeder cover (when the SPF is installed) /document cover Open to make copies from the document glass. (p.18) Document glass Place an original that you wish to scan face down here. (p.18) Handles Use to move the machine.
AR-5316-5320-EX.book 9 ページ ２００３年１１月２６日 水曜日 午後５時３分 BEFORE USING THE MACHINE 17 18 19 1 20 21 22 24 26 25 27 23 16 17 18 19 20 21 22 Parallel connector Connect to your computer to use the printer function. (Software Setup Guide) Document feeder tray (when the SPF is installed) Place the original(s) that you wish to scan face up here. Holds up to 40 originals. Original guides (when the SPF is installed) Adjust to the size of the originals.
AR-5316-5320-EX.book 10 ページ ２００３年１１月２６日 水曜日 午後５時３分 BEFORE USING THE MACHINE OPERATION PANEL 1 2 3 The indications of the operation panel may differ depending on the country and the region. The example of a display of inch series AR-5316/ AR-5316 X 200% 141 129 121 100% 95 77 64 50% 11X17 8½X14 8½X11 8½X5½ 8½X11 8½X13 EXTRA 18 1 2 3 4 5 6 7 21 15 ON LINE key ( ) / indicator Press to toggle the machine between online and off-line.
AR-5316-5320-EX.book 11 ページ ２００３年１１月２６日 水曜日 午後５時３分 BEFORE USING THE MACHINE 6 4 (Two-tray model only) 7 5 ACC.#-C 8 AUTO A3 A4 A4 A5 B4 EXTRA 1 3 5 12 13 ZOOM 25 400% INTERRUPT 1 AUTO % ENTER 15 11 200% 141 122 115 100% 86 81 70 50% AUTO 14 10 9 16 17 18 19 20 21 22 24 23 25 26 27 Not used for this machine. 16 17 18 19 20 21 22 PAPER SIZE indicators Light up to show the selected copy paper size. (p.
AR-5316-5320-EX.book 12 ページ ２００３年１１月２６日 水曜日 午後５時３分 POWER ON AND OFF The power switch is located on the left side of the machine. POWER ON POWER OFF Turn the power switch to the "ON" position. Make sure that the machine is not in operation and then turn the power switch to the "OFF" position. It will take about 45 seconds for the machine to warm up. While the machine is warming up, the POWER SAVE indicator ( ) will blink. (The POWER SAVE indicator ( ) will go off when the machine is ready to copy.
AR-5316-5320-EX.book 13 ページ ２００３年１１月２６日 水曜日 午後５時３分 LOADING PAPER The paper required indicator ( ) will light up when there is no copy paper in the selected paper feed tray, or when the selected paper tray is not installed or is improperly installed. PAPER For best results, use only SHARP recommended paper. Paper tray type Paper tray Bypass tray Paper type Size A5*1 Weight g/m2 Standard paper Recycled paper 56 A4 (15 lbs.
AR-5316-5320-EX.book 14 ページ ２００３年１１月２６日 水曜日 午後５時３分 BEFORE USING THE MACHINE LOADING PAPER Make sure that the machine is not copying or printing, and then follow these steps to load paper. Loading the paper tray 1 Gently lift and pull out the paper tray until it stops. 2 Push the pressure plate down until it locks in place. Push the centre of the pressure plate down until it locks into place. 3 Fan the paper. If the paper is not fanned, double-feeds or misfeeds may occur.
AR-5316-5320-EX.book 15 ページ ２００３年１１月２６日 水曜日 午後５時３分 BEFORE USING THE MACHINE Loading the bypass tray 1 Unfold the bypass tray. 3 Insert the paper (print face down) all the way into the bypass tray. To prevent a misfeed, verify once more that the paper guides are adjusted to the width of the paper. When feeding large paper such as B4 and A3 (8-1/2" x 14" and 11" x 17"), pull out the bypass tray extension.
AR-5316-5320-EX.book 16 ページ ２００３年１１月２６日 水曜日 午後５時３分 BEFORE USING THE MACHINE Envelopes Do not use the following envelopes, as misfeeds will occur. • Envelopes with metal tabs, clasps, strings, holes, or windows. • Envelopes with rough fibres, carbon paper, or glossy surfaces. • Envelopes with two or more flaps. • Envelopes with tape, film, or paper attached to the flap. • Envelopes with a fold in the flap. • Envelopes with glue on the flap to be moistened for sealing. • Envelopes with labels or stamps.
AR-5316-5320-EX.book 17 ページ ２００３年１１月２６日 水曜日 午後５時３分 BEFORE USING THE MACHINE 4 Squeeze the lock lever of the front guide and slide the front guide to match the width of the paper, and move the left guide to the appropriate slot as marked on the tray. Important points when using the printer mode • Make sure that the tray's paper size setting is the same as the tray's paper size setting in the printer driver. For example, if the tray's paper size setting is A4R, set "Setting Paper Size" to "A4-R".
AR-5316-5320-EX.book 18 ページ 2 ２００３年１１月２６日 水曜日 午後５時３分 Chapter 2 COPY FUNCTIONS This chapter explains basic copying functions such as normal copying, reduction or enlargement, and exposure adjustment. NORMAL COPYING This section explains how to make a regular copy. If "Auditing mode" has been enabled (p.39), enter your 3-digit account number. Copying from the document glass 1 Open the document cover/SPF, and place the original.
AR-5316-5320-EX.book 19 ページ ２００３年１１月２６日 水曜日 午後５時３分 COPY FUNCTIONS Copying from the SPF 1 2 Make sure that an original has not been left on the document glass. Close the SPF. 5 Press the [START] key ( copying. The copy is delivered to the paper output tray. Adjust the original guides to the size of the original(s). Note 3 ) to begin Set the original(s) face up in the document feeder tray. • The paper output tray can hold up to 250 sheets of paper.
AR-5316-5320-EX.book 20 ページ ２００３年１１月２６日 水曜日 午後５時３分 COPY FUNCTIONS Auto paper select mode (Two-tray model only) When the AUTO PAPER SELECT indicator ( AUTO ) lights up, "Auto paper select mode" is enabled. This function automatically selects the paper that is the same size as the original A5, A4, A4R, B4, A3 (5-1/2" x 8-1/2", 8-1/2" x 11", 8-1/2" x 11"R, 8-1/2" x 13", 8-1/2" x 14" and 11" x 17") paper. "Auto paper select mode" can be disabled in the user programs. (p.
AR-5316-5320-EX.book 21 ページ ２００３年１１月２６日 水曜日 午後５時３分 COPY FUNCTIONS MAKING A COPY DARKER OR LIGHTER Automatic exposure adjustment is initially enabled. This function automatically adjusts the copy image according to the original being copied. If you wish to select the exposure level yourself, follow the steps below. (Select from two original types and five exposure levels for each original type.) The exposure level used in automatic exposure adjustment can also be changed.
AR-5316-5320-EX.book 22 ページ ２００３年１１月２６日 水曜日 午後５時３分 COPY FUNCTIONS SETTING THE NUMBER OF COPIES Press the numeric keys to set the number of copies. Important note when making a large number of copies ● The set number of copies appears in the display. A maximum of 999 copies (factory default setting) can be set. ● If you wish to make only a single copy, copying is possible with the display showing "0". Note The maximum number of copies can be changed in the user programs. (p.
AR-5316-5320-EX.book 23 ページ ２００３年１１月２６日 水曜日 午後５時３分 COPY FUNCTIONS 4 Press the [AUTO IMAGE] key ( AUTO % ). The AUTO IMAGE indicator ( AUTO % ) lights up and the appropriate ratio for the original size and paper size is selected. (The indicator of the selected ratio will light up.) AUTO % Note 5 Set the number of copies and other copy settings, and then press the [START] key ( ). The copy will be delivered to the paper output tray.
AR-5316-5320-EX.book 24 ページ ２００３年１１月２６日 水曜日 午後５時３分 COPY FUNCTIONS SELECTING THE VERTICAL AND HORIZONTAL COPY RATIOS SEPARATELY (XY ZOOM copying) The XY ZOOM feature allows the horizontal and vertical copy ratios to be changed independently. Example: Reduction only in the horizontal direction. Original Note Copy • To use the XY ZOOM feature with the DUAL PAGE COPY feature, set the DUAL PAGE COPY feature first and then the XY ZOOM feature.
AR-5316-5320-EX.book 25 ページ ２００３年１１月２６日 水曜日 午後５時３分 COPY FUNCTIONS 6 Use the [PRESET RATIO] selector keys ( , ) and [Zoom] keys ( , to change the copy ratio in the horizontal direction. ) Press the [PRESET RATIO] selector keys ( , ) to select a ratio close to the desired ratio, and then press the [Zoom] keys ( , ) to adjust the ratio in increments of 1%. The ratio appears in the display. 7 Press the [Copy ratio display] key ( ).
AR-5316-5320-EX.book 26 ページ ２００３年１１月２６日 水曜日 午後５時３分 TWO-SIDED COPYING USING THE BYPASS TRAY To perform manual two-sided copying, follow these steps. Example: Copying originals A and B onto each side of one sheet of paper 1 2 1 Copy Original A Original B 1 3 Copy original A. Turn the copy of original A over, and without changing the position of the edge closest to you, insert it in the bypass tray. Insert the paper all the way in.
AR-5316-5320-EX.book 27 ページ ２００３年１１月２６日 水曜日 午後５時３分 DUAL PAGE COPYING A dual page original can be automatically separated into two pages during copying. This feature is convenient for making copies of books and other dual page originals on individual sheets of paper. Original Note 1 • • • • • Copy A4 (8-1/2" x 11") paper is used for dual page copying. When used in combination with XY ZOOM copying, enlargement is not possible.
AR-5316-5320-EX.book 28 ページ ２００３年１１月２６日 水曜日 午後５時３分 INTERRUPTING A COPY RUN (Interrupt copying) A copy run can be temporarily interrupted to allow another copy job to be performed. When the other job is finished, the copy run will resume using the original copy settings. Note 1 Interrupt copying is not possible when the user programs are being configured. Press the [INTERRUPT] key ( interrupt the copy run.
AR-5316-5320-EX.book 29 ページ 3 ２００３年１１月２６日 水曜日 午後５時３分 Chapter 3 PRINTER FUNCTIONS The machine includes a USB 1.1 connector and a parallel connector as standard equipment. A computer can be connected to these connectors to use the machine as a printer. To use the machine as a printer, the printer driver must first be installed as explained in the "Software Setup Guide". Note • If a problem occurs in printer mode, see "TROUBLESHOOTING" (p.40).
AR-5316-5320-EX.book 30 ページ ２００３年１１月２６日 水曜日 午後５時３分 PRINTER FUNCTIONS Pausing a print job To pause a print job during printing, press the [ON LINE] key ( ) on the operation panel to switch the machine off-line. Printing will be paused and the ON LINE indicator ( ) will blink. To cancel a print job, press the [CLEAR] key ( ) or the [CLEAR ALL] key ( ). To resume printing, press the [ON LINE] key ( ) to switch the machine online.
AR-5316-5320-EX.book 31 ページ 4 ２００３年１１月２６日 水曜日 午後５時３分 Chapter 4 USER SETTINGS This chapter explains how to set the automatic exposure level, toner save mode/high image quality mode, and the user programs, which are custom settings that control fine points of the machine’s operation. ADJUSTING THE AUTOMATIC EXPOSURE LEVEL The exposure level used in automatic exposure adjustment, which automatically adjusts the copy exposure according to the original, can be adjusted.
AR-5316-5320-EX.book 32 ページ ２００３年１１月２６日 水曜日 午後５時３分 TONER SAVE MODE AND HIGH IMAGE QUALITY MODE Toner save mode can be enabled to reduce toner consumption by about 10%. The high image quality mode improves copy image quality in the automatic and manual exposure modes by increasing copy density with a slight increase of toner consumption. To switch between toner save mode and high image quality mode, follow the steps below. Note In Europe, high image quality mode is initially selected.
AR-5316-5320-EX.book 33 ページ ２００３年１１月２６日 水曜日 午後５時３分 CUSTOMISING SETTINGS (User programs) The user programs allow you to customise the machine to match your needs. USER PROGRAMS Program number 1 2 Program name Auto clear time Preheat mode Setting codes (factory default setting appears in bold) 1: OFF 2: 10 sec. 3: 20 sec. 4: 60 sec. 5: 90 sec. 6: 120 sec. 1: 1 min. 2: 5 min. 3: 30 min. 4: 60 min. 5: 120 min. 6: 240 min. 3 Auto power shut-off timer 1: 5 min. 2: 30 min. 3: 60 min. 4: 120 min.
AR-5316-5320-EX.book 34 ページ ２００３年１１月２６日 水曜日 午後５時３分 USER SETTINGS Program number Program name 23 Resolution in Auto/Text mode 1: 300 dpi 2: 600 dpi 25 Key auto repeat 0: OFF 1: ON 26 27 28 29 1: Minimum (current response speed) Key press time 2: 0.5 sec. 3: 1.0 sec. 4: 1.5 sec. 5: 2.0 sec.
AR-5316-5320-EX.book 35 ページ ２００３年１１月２６日 水曜日 午後５時３分 USER SETTINGS SELECTING A SETTING FOR A USER PROGRAM 1 Hold down the [Light] key ( the alarm indicators ( , , ) blink. ) until , , 4 Enter the desired setting code by pressing a numeric key. • For the setting codes, see "USER PROGRAMS". (p.33 to p.34) • The selected setting code blinks. • For example, to select 90 seconds, press the [5] key. The display shows "- -" with the left hyphen blinking.
AR-5316-5320-EX.book 36 ページ ２００３年１１月２６日 水曜日 午後５時３分 SETTINGS FOR AUDITING MODE AUDITING MODE When "Auditing mode" is enabled, a count is kept of the number of copies made by each account (up to 20 accounts can be established), and the counts can be displayed and totalled as necessary. In "Auditing mode", the display shows "- - -", and this indicates that a 3-digit account number must be entered in order to use the machine for copying.
AR-5316-5320-EX.book 37 ページ ２００３年１１月２６日 水曜日 午後５時３分 USER SETTINGS SELECTING AUDITING MODE SETTINGS 1 Hold down the [Light] key ( the alarm indicators ( , , ) blink. ) until , , The display shows "- -" with the left hyphen blinking. 5 Press the [Light] key ( the settings. ) to complete The alarm indicators ( , , , , ) go off and the display returns to the number of copies display. 1 3 5 2 Enter the program number with the numeric keys. READ END Note 3 • See "AUDITING MODE SETTINGS" (p.
AR-5316-5320-EX.book 38 ページ ２００３年１１月２６日 水曜日 午後５時３分 USER SETTINGS Auditing mode Account number deletion (program No.10) (program No.13) 1 Use this procedure to delete account numbers. A single account number can be deleted, or all account numbers at once. If no account numbers have been established, the error code "13E" will appear in the display. Press the [1] key to enable "Auditing mode" or the [0] key to disable it, and then press the [START] key ( ).
AR-5316-5320-EX.book 39 ページ ２００３年１１月２６日 水曜日 午後５時３分 USER SETTINGS Resetting account (program No.15) The copy count of a single account or all accounts can be reset to 0. If no account numbers have been established, the error code "15E" will appear in the display. Copying when "Auditing mode" is enabled When "Auditing mode" is enabled, "- - -" appears in the display. [Resetting all accounts] Press the [1] key and then press the [START] key ( ). The copy counts of all accounts will be deleted.
AR-5316-5320-EX.book 40 ページ 5 ２００３年１１月２６日 水曜日 午後５時３分 Chapter 5 TROUBLESHOOTING This chapter describes troubleshooting and misfeed removal. TROUBLESHOOTING If you experience difficulty using the machine, check the following troubleshooting guide before calling for service. Many problems can be easily resolved by the user. If you are unable to solve the problem using the troubleshooting guide, turn off the power switch and unplug the machine, and contact your authorised service representative.
AR-5316-5320-EX.book 41 ページ ２００３年１１月２６日 水曜日 午後５時３分 TROUBLESHOOTING MACHINE/COPYING PROBLEMS The following problems are related to the general operation of the machine and copying. Problem Cause and solution The machine is not plugged into a power outlet. → Plug the machine into a grounded outlet. Power switch OFF. – 12 → Turn the power switch ON. The POWER SAVE indicator ( Page ) is blinking. → Indicates that the machine is warming up.
AR-5316-5320-EX.book 42 ページ ２００３年１１月２６日 水曜日 午後５時３分 TROUBLESHOOTING Problem Cause and solution Misfeed occurs. → To remove the misfeed, see "MISFEED REMOVAL". The paper is outside of the specified size and weight range. Page 47 13 → Use copy paper within the specified range. Paper curled or damp. → Do not use curled or crimped paper. Replace with dry copy paper.
AR-5316-5320-EX.book 43 ページ ２００３年１１月２６日 水曜日 午後５時３分 TROUBLESHOOTING Problem Cause and solution The document glass or the underside of the document cover/SPF is dirty. Page 56 → Clean regularly. Copies are smudged or dirty. Original smudged or blotchy. – → Use a clean original. The scanner glass in the SPF is dirty. → Clean the long, narrow glass in the SPF. White or black lines appear on copies. The transfer charger is dirty. 57 → Clean the transfer charger.
AR-5316-5320-EX.book 44 ページ ２００３年１１月２６日 水曜日 午後５時３分 TROUBLESHOOTING PRINTING PROBLEMS In addition to this section, troubleshooting information can also be found in the README files for each of the software programs. To view a README file, see the "Software Setup Guide". Problem Cause and solution Page The machine is set to off-line mode. → Press the [ON LINE] key ( ( ). ) to turn on the ON LINE indicator 29 The machine is not correctly connected with your computer.
AR-5316-5320-EX.book 45 ページ ２００３年１１月２６日 水曜日 午後５時３分 TROUBLESHOOTING Problem Printing is slow. Cause and solution Simultaneous use of two or more application software programs. Page – → Start printing after quitting all unused application software programs. The printed image is light and uneven. The paper is loaded so that printing takes place on the back side of the paper. → Some paper types have a front and back side.
AR-5316-5320-EX.book 46 ページ ２００３年１１月２６日 水曜日 午後５時３分 INDICATORS AND DISPLAY MESSAGES If one of the following indicators lights up or one of the following messages appears in the display, check the meaning of the indicator or message in the following table and take appropriate action.
AR-5316-5320-EX.book 47 ページ ２００３年１１月２６日 水曜日 午後５時３分 MISFEED REMOVAL When a misfeed occurs, the misfeed indicator ( ) and a misfeed location indicator ( ) will blink and the machine will automatically stop. Check the blinking misfeed location indicator to identify the location of the misfeed and remove it. Note The paper may tear when you remove a misfeed. In this event, be sure to remove all torn pieces of paper from the machine, taking care not to touch the photoconductive drum (the green part).
AR-5316-5320-EX.book 48 ページ ２００３年１１月２６日 水曜日 午後５時３分 TROUBLESHOOTING Section C Remove the misfed original from the exit area. 2 Open and close the SPF to make the misfeed location indicator stop blinking. You can also make the misfeed indicator stop blinking by opening and closing the feeding roller cover or the right side cover. If the misfed original cannot be easily removed from the exit area, open the moveable part of the document feeder tray and remove the original.
AR-5316-5320-EX.book 49 ページ ２００３年１１月２６日 水曜日 午後５時３分 TROUBLESHOOTING MISFEED IN THE MACHINE 1 Open the bypass tray and the side cover. 2 Check the misfeed location. Remove the misfed paper following the instructions for each location in the illustration below. If paper is misfed here, go to "B. Misfeed in the fusing area". If the misfed paper is visible here, go to "C. Misfeed in the transport area". If paper is misfed here, go to "A. Misfeed in the paper feed area". A.
AR-5316-5320-EX.book 50 ページ ２００３年１１月２６日 水曜日 午後５時３分 TROUBLESHOOTING B. Misfeed in the fusing area 1 Push gently on both ends of the front cover. 2 Turn the roller rotating knob in the direction of the arrow. 4 Lift the fusing unit release levers, to return them to their operating positions. 5 Close the front cover and side cover. Roller rotating knob 3 The misfeed indicator ( ) will go out. Carefully remove the misfed paper. Lower the fusing unit release levers to allow easier removal.
AR-5316-5320-EX.book 51 ページ ２００３年１１月２６日 水曜日 午後５時３分 TROUBLESHOOTING C. Misfeed in the transport area 1 Open the fusing paper guide by pressing down the projection on either side of the guide and remove the misfed paper. Be careful not to tear the misfed paper during removal. The fusing unit is hot. Do not touch Warning the fusing unit when removing misfed paper. Doing so may cause a burn or injury.
AR-5316-5320-EX.book 52 ページ ２００３年１１月２６日 水曜日 午後５時３分 TROUBLESHOOTING MISFEED IN THE UPPER PAPER TRAY Note 1 Make sure that there is no misfed paper in the tray before pulling it out. (p.49) Lift and pull out the upper paper tray and remove the misfed paper. Be careful not to tear the misfed paper during removal. 2 Open and close the side cover. The misfeed indicator ( ) will go out. Note 3 • When closing the side cover, press on the handle.
AR-5316-5320-EX.book 53 ページ ２００３年１１月２６日 水曜日 午後５時３分 TROUBLESHOOTING MISFEED IN THE LOWER PAPER TRAY (Two-tray model only) Note 1 Make sure that there is no misfed paper in the tray before pulling it out. (p.49) Open the lower side cover. 5 Close the lower paper tray. Grasp the handle to open the lower side cover. 2 Remove the misfed paper. Be careful not to tear the misfed paper during removal.
AR-5316-5320-EX.book 54 ページ ２００３年１１月２６日 水曜日 午後５時３分 REPLACING THE TONER CARTRIDGE When the toner cartridge replacement required indicator ( ) lights up, the toner cartridge will need replacement soon. Obtain a new cartridge. When the toner cartridge replacement required indicator ( ) blinks, the toner cartridge must be replaced before copying can be resumed. Replace the toner cartridge by following the procedure below.
AR-5316-5320-EX.book 55 ページ 6 ２００３年１１月２６日 水曜日 午後５時３分 Chapter 6 ROUTINE MAINTENANCE This chapter explains how to keep the machine operating smoothly, including viewing copy count, the toner level indicator, and cleaning the machine. CHECKING THE TOTAL OUTPUT COUNT AND TONER LEVEL CHECKING THE TOTAL OUTPUT COUNT From the "0" display, you can check the total output count, total copy count, as explained below.
AR-5316-5320-EX.book 56 ページ ２００３年１１月２６日 水曜日 午後５時３分 ROUTINE MAINTENANCE CHECKING THE TONER LEVEL The toner level is indicated by a 6-level display. Use it as a guideline for replacing the toner cartridge. 1 Hold down the [Light] key ( the alarm indicators ( , , blink. ) until , , ) 2 The display will show "- -". Hold down the [Copy ratio display] key ( ) for more than 5 seconds. ZOOM 1 3 5 3 The approximate quantity of toner remaining will be indicated in the display as a percentage.
AR-5316-5320-EX.book 57 ページ ２００３年１１月２６日 水曜日 午後５時３分 ROUTINE MAINTENANCE CLEANING THE BYPASS TRAY PAPER FEED ROLLER If misfeeds occur frequently when feeding envelopes, thick paper, etc. through the bypass tray, wipe the paper feed roller at the feed slot of the bypass tray with a soft, clean cloth dampened with alcohol or water. Paper feed roller CLEANING THE TRANSFER CHARGER If copies start becoming streaky or blotchy, the transfer charger may be dirty.
AR-5316-5320-EX.book 58 ページ ２００３年１１月２６日 水曜日 午後５時３分 Chapter 7 7 PERIPHERAL DEVICES AND SUPPLIES Optional equipment and supplies are explained in this chapter. To purchase optional equipment and supplies, contact your authorised service representative. PERIPHERAL DEVICES Note As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice.
AR-5316-5320-EX.book 59 ページ ２００３年１１月２６日 水曜日 午後５時３分 STORAGE OF SUPPLIES Standard supplies for this product that are to be replaced by the user are paper and toner cartridge. For best copying results, be sure to use only SHARP products. Only genuine SHARP consumables carry the Genuine Supplies label. GENUINE SUPPLIES PROPER STORAGE ● Store the supplies in a location that is: clean and dry, at a stable temperature, not exposed to direct sunlight. ● Store paper in the wrapper and lying flat.
AR-5316-5320-EX.book 60 ページ 8 ２００３年１１月２６日 水曜日 午後５時３分 Chapter 8 APPENDIX SPECIFICATIONS Model AR-5316/5316 X AR-5320/5320 X Type Digital Multifunctional System, Desktop Photoconductive type OPC drum Document glass type Fixed Copy system Dry, electrostatic transfer Originals Sheets, bound documents Original sizes Max. A3 (11" x 17") Copy size Max. A3 (11" x 17") Min. A6 (5-1/2" x 8-1/2") (A6 must be fed from the bypass tray) Image loss: Max.
AR-5316-5320-EX.book 61 ページ ２００３年１１月２６日 水曜日 午後５時３分 APPENDIX Weight Approx. 31.3 kg (69.1 lbs.) (Not including toner cartridge) Approx. 36.3 kg (80.1 lbs.
AR-5316-5320-EX.book 62 ページ ２００３年１１月２６日 水曜日 午後５時３分 SOFTWARE LICENSE PLEASE READ THIS LICENSE CAREFULLY BEFORE USING THE SOFTWARE. BY USING THE SOFTWARE, YOU ARE AGREEING TO BE BOUND BY THE TERMS OF THIS LICENSE. 1. License. The application, demonstration, system and other software accompanying this License, whether on disk, in read only memory, or on any other media (the "Software") and related documentation are licensed to you by SHARP.
AR-5316-5320-EX.book 63 ページ ２００３年１１月２６日 水曜日 午後５時３分 6. Limited Warranty on Media. SHARP warrants the disks on which the Software is recorded to be free from defects in materials and workmanship under normal use for a period of ninety (90) days from the date of purchase as evidenced by a copy of the receipt. The entire liability of SHARP and/or its Licensors and your exclusive remedy will be replacement of the disk which fails to meet the limited warranty provided by this Clause 6.
AR-5316-5320-EX.book 64 ページ ２００３年１１月２６日 水曜日 午後５時３分 INDEX Symbols [ ] key..........................................................11, 55 A About the operation manuals - Online Manual.....................................................5 - Operation Manual ...............................................5 - Software Setup Guide.........................................5 Adjusting the automatic exposure level....................31 Alarm indicators .........................10, 35, 37, 43, 45, 46 Appendix ...
AR-5316-5320-EX.book 65 ページ ２００３年１１月２６日 水曜日 午後５時３分 Original types - AUTO ................................................................21 - PHOTO .............................................................21 - TEXT.................................................................21 P Paper........................................................................13 Paper feed location indicator..............................11, 16 Paper output tray........................................................
AR-5316-5320-EX.book 66 ページ ２００３年１１月２６日 水曜日 午後５時３分 INDEX BY PURPOSE Copying Automatic ratio selection ..........................................22 Cancelling a copy run.........................................18, 19 Copying, starting ................................................18, 19 Dual page copying .................................................. 27 Enlargement/reduction ............................................ 22 Exposure adjustment ..............................................
AR-5316-5320-EX.
AR-5316-5320-EX.
AR-5316-5320-EX.
AR-5316-5320-EX.
