INA KS1 QSZZ Pegasus-E_Fax_Sec.book 1 ページ ２００４年９月２４日 金曜日 午後２時５１分 MODEL AR-FX11 FACSIMILE EXPANSION KIT OPERATION MANUAL Page • BEFORE USING 9 THE FAX FUNCTION 19 • BASIC OPERATIONS • ADVANCED TRANSMISSION 34 METHODS • TRANSMISSION USING 50 F-CODES • CONVENIENT METHODS 62 OF USE 64 • PROGRAMMING 88 • TROUBLESHOOTING • KEY OPERATOR 94 PROGRAMS 110 • APPENDIX Be sure to become thoroughly familiar with this manual to gain the maximum benefit from the product.
Pegasus-E_Fax_Sec.book 2 ページ ２００４年９月２４日 金曜日 午後２時５１分 ■ CAUTION: To reduce the risk of fire, use only UL-Listed No.26 AWG or larger telecommunication line cord. ■ WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. ■ FAX interface cable and Line cable: These special accessories must be used with the device.
Pegasus-E_Fax_Sec.book 1 ページ ２００４年９月２４日 金曜日 午後２時５１分 INTRODUCTION Thank you for purchasing this product. This manual only explains the facsimile functions of the product. For safety precautions and general information on using the machine such as loading paper, clearing misfeeds, and handling peripheral units, see the "Operation manual (for general information and copier)".
Pegasus-E_Fax_Sec.book 2 ページ ２００４年９月２４日 金曜日 午後２時５１分 CONTENTS INTRODUCTION ........................................................................................................................................ 1 CONNECTING AN EXTENSION PHONE.................................................................................................. 1 TO USE THIS PRODUCT CORRECTLY AS A FACSIMILE.....................................................................
Pegasus-E_Fax_Sec.book 3 ページ ２００４年９月２４日 金曜日 午後２時５１分 CONTENTS F-CODE RELAY BROADCAST TRANSMISSION .............................................. 60 ● USING THE F-CODE RELAY BROADCAST FUNCTION (your machine is the relay machine) ......61 ● USING THE F-CODE RELAY REQUEST FUNCTION (your machine requests a relay broadcast) ...........61 5 CONVENIENT METHODS OF USE CONNECTING AN EXTENSION PHONE........ 62 ● USING AN EXTENSION PHONE ...................62 ● SETTING THE RECEPTION MODE ..............
Pegasus-E_Fax_Sec.book 4 ページ ２００４年９月２４日 金曜日 午後２時５１分 TO USE THIS PRODUCT CORRECTLY AS A FACSIMILE Several points must be kept in mind when using this product as a facsimile. Please note the following. Line connection Be sure to use the provided telephone line cord to connect the machine to a telephone line jack. Insert one end of the telephone line cord into the LINE jack on the left side of the machine as shown. Insert the other end of the telephone line cord into a telephone line jack.
Pegasus-E_Fax_Sec.book 5 ページ ２００４年９月２４日 金曜日 午後２時５１分 TO USE THIS PRODUCT CORRECTLY AS A FACSIMILE Lithium battery A lithium battery in the machine is used to retain settings and programmed information such as auto-dial numbers (page 64). • When the battery dies, settings and programmed information will be lost, so please keep a record of this information. (See "PRINTING LISTS OF PROGRAMMED INFORMATION, SETTINGS, AND COMMUNICATION ACTIVITY" on page 83.
Pegasus-E_Fax_Sec.book 6 ページ ２００４年９月２４日 金曜日 午後２時５１分 TO USE THIS PRODUCT CORRECTLY AS A FACSIMILE FCC NOTICE TO USERS This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this information must be provided to the telephone company.
Pegasus-E_Fax_Sec.
Pegasus-E_Fax_Sec.book 8 ページ ２００４年９月２４日 金曜日 午後２時５１分 TO USE THIS PRODUCT CORRECTLY AS A FACSIMILE NOTICE FOR USERS IN CANADA NOTICE : This product meets the applicable Industry Canada technical specifications. NOTICE : The Ringer Equivalence Number is an indication of the maximum number of devices allowed to be connected to a telephone interface.
Pegasus-E_Fax_Sec.book 1 9 ページ ２００４年９月２４日 金曜日 午後２時５１分 BEFORE USING THE FAX FUNCTION This chapter contains basic information about using the fax function of the machine. Please read this chapter before using the fax function. POINTS TO CHECK AND PROGRAM AFTER INSTALLATION After installing the machine and before using it as a fax machine, check the following points and program the required information. Set the date and time The machine has an internal clock.
Pegasus-E_Fax_Sec.book 10 ページ ２００４年９月２４日 金曜日 午後２時５１分 PART NAMES AND FUNCTIONS OPERATION PANEL (1) 26 27 28 29 41 30 42 43 44 45 COPY A 31 B 32 F 36 G 37 K C 33 H 38 L D 34 I 39 M E Q 47 J 40 N P 46 35 U R 48 V W SPEAKER REDIAL/PAUSE O SHIFT S 49 T 50 XYZ SP SPEED COMM. SETTING SYMBOL SPACE/– ON LINE DATA PRINT SCAN LINE DATA FAX (9) (1) Page pallet (page 84) (2) Display (page 12) This key displays the base screen and the function setting screen.
Pegasus-E_Fax_Sec.book 11 ページ ２００４年９月２４日 金曜日 午後２時５１分 BEFORE USING THE FAX FUNCTION (2) (3) (4) (5) (6) (7) (8) FAX STATUS BACK COPY EXPOSURE PAPER ZOOM OK ABC DEF GHI JKL MNO PQRS TUV WXYZ AUTO % OUTPUT DUPLEX @.-_ SPECIAL FUNCTION SCAN COLOR MODE RESOLUTION ADDRESS FORMAT ORIGINAL SIZE DUPLEX SCAN FAX PROGRAM RESOLUTION ADDRESS BROADCAST ORIGINAL SIZE DUPLEX SCAN (16) (17) (18) (19) (20) (21) ACC.
Pegasus-E_Fax_Sec.book 12 ページ ２００４年９月２４日 金曜日 午後２時５１分 BEFORE USING THE FAX FUNCTION FAX MODE (BASE SCREEN) The base screen of fax mode is displayed by pressing the [FAX] key when the print mode, copy mode, or scan mode screen appears. The base screen of fax mode (1) (2) (3) (4) (5) (1) Stand-by. 96% MAY 10 MON 10:25 AM MEMORY AUTO CONT AUTO 812 x11R STANDARD Message display Messages appear here to indicate the current status of the machine.
Pegasus-E_Fax_Sec.book 13 ページ ２００４年９月２４日 金曜日 午後２時５１分 BEFORE USING THE FAX FUNCTION AUDITING MODE Accounts that can transmit faxes (up to 50) can be established and transmission time and other information can be tracked for each account. The Acc. Usage List (page 97) can be printed out which shows the time used for transmission and pages transmitted by each account. • This function is enabled using "ACCOUNT CONTROL" and "ACCOUNT # SET" in the key operator programs.
Pegasus-E_Fax_Sec.
Pegasus-E_Fax_Sec.book 15 ページ ２００４年９月２４日 金曜日 午後２時５１分 PLACING THE ORIGINAL An original can be placed in the SPF or on the document glass. Use the SPF when faxing a large number of sheet originals. Use the document glass to fax originals that cannot be scanned using the SPF such as thick or thin sheet originals, or books or other bound originals. USING THE SPF 1 2 Open the SPF, make sure that an original has not been left on the document glass, and then gently close the SPF.
Pegasus-E_Fax_Sec.book 16 ページ ２００４年９月２４日 金曜日 午後２時５１分 CHECKING THE SIZE OF A PLACED ORIGINAL When a standard-size* original is placed, the original size is automatically detected (automatic original detection function) and displayed in the original display. Make sure that the size has been detected correctly. (1) When an original is placed, an icon appears to indicate the original scanning mode. : One-sided scanning in the SPF. : Scanning on the document glass : Two-sided scanning in the RSPF.
Pegasus-E_Fax_Sec.book 17 ページ ２００４年９月２４日 金曜日 午後２時５１分 SELECTING RESOLUTION AND EXPOSURE SETTINGS The resolution and exposure can be adjusted to match the size and darkness of text on the original, or for an original such as a photograph. To change the settings, follow the steps below after selecting fax mode and placing the original.
Pegasus-E_Fax_Sec.book 18 ページ ２００４年９月２４日 金曜日 午後２時５１分 CONVENIENT DIALING METHODS (AUTO-DIALING) The fax function includes a convenient auto dial feature (Rapid dialing, speed dialing and group dialing). By programming frequently dialed numbers, you can call and send faxes to these locations by means of a simple dialing operation (page 22). There are three types of auto-dialing: Rapid dialing, speed dialing, and group dialing. To program auto-dial numbers, see page 64.
Pegasus-E_Fax_Sec.book 2 19 ページ ２００４年９月２４日 金曜日 午後２時５１分 BASIC OPERATIONS This chapter explains the basic procedures for sending and receiving faxes. There are three basic methods for fax transmission: memory transmission, direct transmission, and manual transmission. When memory transmission is used, the document is temporarily stored in memory before being transmitted.
Pegasus-E_Fax_Sec.book 20 ページ ２００４年９月２４日 金曜日 午後２時５１分 SENDING A FAX BASIC PROCEDURE FOR SENDING FAXES 1 Make sure that the machine is in fax mode. SCAN The FAX indicator is lit when the machine is in fax mode. If the LINE DATA COPY EXP indicator is not lit, press the FAX SCAN COL [FAX] key. If auditing mode has FAX PR been enabled for the fax function in the key operator programs, a message will appear prompting you to enter your account number when you switch to fax mode.
Pegasus-E_Fax_Sec.book 21 ページ ２００４年９月２４日 金曜日 午後２時５１分 BASIC OPERATIONS Using the SPF 6 Press the [START] key ( WXYZ Using the document glass READING No.001 MEMORY CONT AUTO STANDARD @.-_ READ-END 6 ). XX% P-XXX AUTO 812 x11R Press the [START] key ( WXYZ ). READING No.001 MEMORY CONT AUTO STANDARD @.-_ READ-END XX% P-XXX AUTO 812 x11R • Scanning begins. • If the line is free, the machine will dial the receiving machine and begin transmission as soon as the first page is scanned.
Pegasus-E_Fax_Sec.book 22 ページ ２００４年９月２４日 金曜日 午後２時５１分 BASIC OPERATIONS TRANSMISSION BY AUTO-DIALING (RAPID DIALING AND GROUP DIALING) Fax numbers can be dialed by automatic dialing (Rapid dialing and group dialing) instead of pressing the numeric keys. Follow the steps below to send a fax using an auto dial number. To use an auto dial number, the name and fax number of the destination must first be stored.
Pegasus-E_Fax_Sec.book 23 ページ ２００４年９月２４日 金曜日 午後２時５１分 BASIC OPERATIONS SEARCHING FOR A PROGRAMMED DESTINATION (USING THE [ADDRESS] KEY) At the time of dialing, you can enter letters to search for a destination stored in a Rapid key, Speed Dial number, or Group key. 1 2 Perform steps 1 to 4 of "BASIC PROCEDURE FOR SENDING FAXES" (page 20). 5 Select the desired destination with the [ ] or [ ] key. GH Press the [ADDRESS] key.
Pegasus-E_Fax_Sec.book 24 ページ ２００４年９月２４日 金曜日 午後２時５１分 BASIC OPERATIONS FAXING A TWO-SIDED ORIGINAL Follow the steps below to automatically transmit both sides of a two-sided original. (This is only possible on models that have an RSPF installed.) Note 1 Do not use an original that is not a standard size (11" x 17", 8-1/2" x 14", 8-1/2" x 11", 8-1/2" x 11"R, A4, A4R). Otherwise a scanning error or cut-off image may result. Make sure that the machine is in fax mode.
Pegasus-E_Fax_Sec.book 25 ページ ２００４年９月２４日 金曜日 午後２時５１分 BASIC OPERATIONS Transmission settings (memory transmission mode and direct transmission mode) Transmission modes include memory transmission, where the original is temporarily scanned into memory before transmission, and direct transmission, where the original is transmitted directly without being scanned into memory.
Chapter02.fm 26 ページ ２００４年１０月５日 火曜日 午後７時３４分 BASIC OPERATIONS 8 Press the [START] key. WXYZ Note When using the document glass, multiple original pages cannot be transmitted in a single transmission. @.-_ READ-END • To change from "Direct Transmission" back to "Memory Transmission", select "MEMORY TX" in step 5. • To cancel a direct transmission, press the [C] key. Faxing by manual transmission (using the [SPEAKER] key) 1 Perform steps 1 to 4 of "BASIC PROCEDURE FOR SENDING FAXES" (page 20).
Pegasus-E_Fax_Sec.book 27 ページ ２００４年９月２４日 金曜日 午後２時５１分 BASIC OPERATIONS Quick On-line When you use the SPF to send a multi-page document and there are no previously stored jobs waiting or in progress (and the line is not being used), the machine dials the destination after the first page is scanned and begins transmitting scanned pages while the remaining pages are being scanned. This transmission method is called Quick On-line.
Pegasus-E_Fax_Sec.book 28 ページ ２００４年９月２４日 金曜日 午後２時５１分 BASIC OPERATIONS CANCELING A FAX TRANSMISSION To cancel a transmission that is in progress or a stored transmission job, follow the steps below. A transmission in progress or a stored transmission job is canceled from the fax status screen. (Printing of a received fax cannot be canceled.
Pegasus-E_Fax_Sec.book 29 ページ ２００４年９月２４日 金曜日 午後２時５１分 BASIC OPERATIONS Canceling a stored transmission job If you do not wish to cancel a stored transmission job and only wish to check its status, press the [BACK] key instead of the [C] key in step 4 to exit. 1 Press the [FAX STATUS] key. Select "YES" with the [ ] or [ ] key. FAX STATUS TX/RX JOBS TX/RX RESERVE TX/RX COMPLETED FAX STATUS BACK 5 OK Job canceled. YES NO The fax job status screen is displayed.
Pegasus-E_Fax_Sec.book 30 ページ ２００４年９月２４日 金曜日 午後２時５１分 RECEIVING FAXES When another fax machine sends a fax to your machine, your machine will ring*, automatically receive the fax, and begin printing. (This is called automatic reception.) If you do not wish to have received faxes printed immediately, use the print hold function to hold received faxes in memory for printing at your convenience (all received faxes will be printed at once).
Pegasus-E_Fax_Sec.book 31 ページ ２００４年９月２４日 金曜日 午後２時５１分 BASIC OPERATIONS F-code confidential fax reception When a fax has been received by F-code confidential fax reception, an icon ( ) will appear in the base screen of fax mode (message display (1) on page 12). The icon also appears in front of the box in the F-code confidential box name screen in the display. (Step 6 on page 59) Print the received fax as explained in "PRINTING A DOCUMENT RECEIVED TO AN F-CODE CONFIDENTIAL MEMORY BOX" (page 59).
Pegasus-E_Fax_Sec.book 32 ページ ２００４年９月２４日 金曜日 午後２時５１分 BASIC OPERATIONS FAX PRINT HOLD FUNCTION Faxes are normally printed as soon as they are received. This function is used to hold received faxes in memory rather than printing them as they are received. Faxes held in memory are printed manually all at once.
Pegasus-E_Fax_Sec.book 33 ページ ２００４年９月２４日 金曜日 午後２時５１分 BASIC OPERATIONS 6 Select "ON" with the [ ] or [ ] key. 7 Press the [OK] key. OK FAX PRINT HOLD ON OFF To disable fax print hold, select "OFF". Printing received faxes held in memory To print received faxes that are held in memory when fax print hold is enabled, follow the steps below. 1 In Fax mode, press the [SPECIAL FUNCTION] key. 4 Select "PRINT HOLD DATA" with the [ ] or [ ] key.
Pegasus-E_Fax_Sec.book 3 34 ページ ２００４年９月２４日 金曜日 午後２時５１分 ADVANCED TRANSMISSION METHODS This chapter explains advanced features that are designed for specific purposes and circumstances. Please read those sections that are of interest to you. SENDING THE SAME DOCUMENT TO MULTIPLE DESTINATIONS IN A SINGLE (BROADCAST TRANSMISSION) OPERATION This feature is used to send a fax to multiple destinations in a single operation.
Pegasus-E_Fax_Sec.book 35 ページ ２００４年９月２４日 金曜日 午後２時５１分 ADVANCED TRANSMISSION METHODS USING BROADCAST TRANSMISSION 1 2 Perform steps 1 to 4 of "BASIC PROCEDURE FOR SENDING FAXES" (page 20). Press the [BROADCAST] key. ENTER RX STATION PER ZOOM AUTO % OUTPUT DUPL OLUTION ADDRESS FORMAT ORIGINAL SIZE DUPLEX OLUTION ADDRESS BROADCAST ORIGINAL SIZE DUPLEX : 4 After entering a full number with the numeric keys, press the BACK OK [OK] key to complete the entry.
Pegasus-E_Fax_Sec.book 36 ページ ２００４年９月２４日 金曜日 午後２時５１分 AUTOMATIC TRANSMISSION AT A (TIMER TRANSMISSION) SPECIFIED TIME This feature enables you to set up a transmission or polling operation to be performed automatically at a specified time up to a week in advance. This is convenient when you will be out of the office or for transmission at off-peak nighttime rates. A combined total of 50 timer transmission and memory transmission jobs can be stored.
Pegasus-E_Fax_Sec.book 37 ページ ２００４年９月２４日 金曜日 午後２時５１分 ADVANCED TRANSMISSION METHODS 8 Press the [OK] key. OK Note The selected day is set. 9 Perform the desired fax operation. The steps that follow will depend on the type of operation.
Pegasus-E_Fax_Sec.book 38 ページ ２００４年９月２４日 金曜日 午後２時５１分 TRANSMISSION AND RECEPTION USING THE POLLING FUNCTION The polling function allows your machine to call a fax machine that has a document ready for transmission and initiate reception of the document. You can also perform the reverse operation: scan a document into the memory of your machine so that another machine can call your machine and initiate reception of the document.
Pegasus-E_Fax_Sec.book 39 ページ ２００４年９月２４日 金曜日 午後２時５１分 ADVANCED TRANSMISSION METHODS USING THE POLLING FUNCTION When used in conjunction with the timer transmission function (page 36), only one polling job can be stored.
Pegasus-E_Fax_Sec.book 40 ページ ２００４年９月２４日 金曜日 午後２時５１分 ADVANCED TRANSMISSION METHODS Serial polling When performing serial polling, an auto-dial key that includes a sub-address or passcode (page 50) cannot be selected. 1 Perform steps 1 to 3 of the polling procedure (page 39). 2 Select "SERIAL POLLING" with the [ ] or [ ] key.
Pegasus-E_Fax_Sec.book 41 ページ ２００４年９月２４日 金曜日 午後２時５１分 ADVANCED TRANSMISSION METHODS USING POLLING MEMORY This function sends a document previously scanned into memory to a receiving machine when the receiving machine calls and polls your machine. (If desired, you can restrict polling to fax machines whose fax number you have programmed in your machine. See "Restricting polling access (polling security)" on page 43.
Pegasus-E_Fax_Sec.book 42 ページ ２００４年９月２４日 金曜日 午後２時５１分 ADVANCED TRANSMISSION METHODS 7 Select "1 TIME" or "REPEAT" with the [ ] or [ ] key. SELECT SENDING 1 TIME REPEAT 9 Press the [START] key ( WXYZ • Scanning begins. • If you are scanning from the document glass and have another page to scan, change pages and press the [START] key ( ). Repeat until all pages have been scanned and then press the key. @.
Chapter03.fm 43 ページ ２００４年９月３０日 木曜日 午前９時７分 ADVANCED TRANSMISSION METHODS Deleting documents from the Public Box This procedure is used to delete documents from the Public Box when they are no longer needed. 1 2 Follow steps 2 to 6 of "Scanning a document into polling memory (the Public Box)" (page 41) and then follow the steps below. 4 Select "YES" with the [ ] or [ ] key. DELETE YES NO Select "DELETE" with the [ ] or [ ] key.
Pegasus-E_Fax_Sec.book 44 ページ ２００４年９月２４日 金曜日 午後２時５１分 INCLUDING SENDER INFORMATION ON FAXES This function prints the date, time, your programmed name, your programmed fax number, and the transmitted page number at the top center of each page that you fax. All pages that you fax include this information. Example of fax page printed out by the receiving machine OCT-22-2004-FRI 03:00 PM (1) SHARP PLANNING DIV. (2) FAX No. 0666211221 (3) P.
Pegasus-E_Fax_Sec.book 45 ページ ２００４年９月２４日 金曜日 午後２時５１分 FAXING A DIVIDED ORIGINAL (DUAL PAGE SCAN) When faxing a book or other bound document, you can use this function to divide the two open pages of the book into two separate fax pages. This function can only be used when the original is scanned using the document glass.
Pegasus-E_Fax_Sec.book 46 ページ ２００４年９月２４日 金曜日 午後２時５１分 ADDING A COVER SHEET/MESSAGE TO A FAX TRANSMISSION This function automatically attaches an 8-1/2" x 11" (A4) cover sheet to your fax transmissions. The cover sheet shows the date and time, the destination name, the sender's name and fax number, and the number of pages in the transmission. A message can also be added to a transmission.
Pegasus-E_Fax_Sec.book 47 ページ ２００４年９月２４日 金曜日 午後２時５１分 USING SETTINGS STORED AS A PROGRAM This function allows you to store the steps of an operation, including the destination and scanning settings, into a program. This function is convenient when you frequently send documents, such as a daily report, to the same destination. Up to nine programs can be stored. When storing a program, a name (maximum 36 letters) can be assigned to the program.
Pegasus-E_Fax_Sec.book 48 ページ ２００４年９月２４日 金曜日 午後２時５１分 FORWARDING RECEIVED FAXES TO ANOTHER MACHINE WHEN PRINTING IS (FORWARDING FUNCTION) NOT POSSIBLE When printing is not possible because of a paper, toner, or other problem, you can forward received faxes to another fax machine if that machine has been appropriately programmed in your machine. This function can be conveniently used in an office or other workplace where there is another fax machine connected to a different phone line.
Pegasus-E_Fax_Sec.book 49 ページ ２００４年９月２４日 金曜日 午後２時５１分 ADVANCED TRANSMISSION METHODS 3 Select "RX DATA TRANSFER" with the [ ] or [ ] key. GH PQR DUPLEX SPECIAL FUNCTION SPECIAL FUNCTION PRINT ENTRY RX DATA TRANSFER DUPLEX SCAN 4 Press the [OK] key. BACK OK GHI 5 Select "TRANSFER" with the [ ] or [ ] key. 3 RX DATA TRANSFER :12345678901234 12345678901234 123456789012 TRANSFER To cancel forwarding, select "NO TRANSFER". 6 Press the [OK] key.
Pegasus-E_Fax_Sec.book 4 50 ページ ２００４年９月２４日 金曜日 午後２時５１分 TRANSMISSION USING F-CODES This chapter explains F-code transmission, which gives you a convenient means of performing advanced operations such as relay broadcast transmission and confidential transmission. Please read those sections that are of interest to you. COMMUNICATION BETWEEN MACHINES SUPPORTING F-CODES This machine supports the "F-code" standard as established by the ITU-T*.
Pegasus-E_Fax_Sec.book 51 ページ ２００４年９月２４日 金曜日 午後２時５１分 TRANSMISSION USING F-CODES When communication occurs involving a box, the communication will only take place if the sub-address and passcode that the other machine sends match the sub-address and passcode programmed in your machine for that box. Therefore, to allow communication, you must inform the other party of the sub-address and passcode of the box.
Pegasus-E_Fax_Sec.book 52 ページ ２００４年９月２４日 金曜日 午後２時５１分 F-CODE POLLING MEMORY F-code polling memory allows one fax machine to call another fax machine and initiate reception of a document that has been scanned into the other machine's F-code polling memory box. Calling another machine and initiating reception is called F-code polling, and scanning a document into a memory box for another machine to retrieve by polling is called F-code polling memory.
Pegasus-E_Fax_Sec.book 53 ページ ２００４年９月２４日 金曜日 午後２時５１分 TRANSMISSION USING F-CODES USING F-CODE POLLING MEMORY In order for another machine to retrieve a document from your machine, you must first scan the document into the F-code polling memory box. You can check the document in the memory polling box by printing it out. (See "Checking and clearing document data in a box" on page 54.) Note When using F-code polling memory, do not set the reception mode to manual reception.
Chapter04.fm 54 ページ ２００４年９月３０日 木曜日 午前９時１１分 TRANSMISSION USING F-CODES Checking and clearing document data in a box The procedures for checking document data in an F-code polling memory box by printing the data and for clearing the data are generally the same as in "Printing documents in the Public Box" (page 42) and "Deleting documents from the Public Box" (page 43). 1 2 Perform steps 2 through 4 of "Scanning a document into polling memory (the Public Box)" on page 41.
Pegasus-E_Fax_Sec.book 55 ページ ２００４年９月２４日 金曜日 午後２時５１分 TRANSMISSION USING F-CODES PROCEDURE FOR F-CODE POLLING Make sure that a document has not been placed in the document feeder tray or on the document glass, and then follow the steps below. Note 1 • You must know the sub-address (SEP) and passcode (PWD) of the other machine's F-code polling memory box.
Pegasus-E_Fax_Sec.book 56 ページ ２００４年９月２４日 金曜日 午後２時５１分 TRANSMISSION USING F-CODES 10 Enter a passcode (maximum 20 digits) with the numeric keys. 11 Press the [OK] key. OK WXYZ • Characters that can be entered are numbers, "#", and spaces. However, the initial character cannot be a space. • If you make a mistake, press the [C] key and re-enter the correct digit(s). • If the other machine has not programmed a passcode, omit the passcode and go to the next step.
Pegasus-E_Fax_Sec.book 57 ページ ２００４年９月２４日 金曜日 午後２時５１分 F-CODE CONFIDENTIAL TRANSMISSION F-Code confidential transmission provides a secure means of faxing confidential documents. The sub-address and passcode programmed in the box restrict the recipients of the fax, and once received in the box, the fax can only be printed by someone who knows the print passcode.
Pegasus-E_Fax_Sec.book 58 ページ ２００４年９月２４日 金曜日 午後２時５１分 TRANSMISSION USING F-CODES F-code confidential transmission 1 2 Follow steps 1 to 4 of "BASIC PROCEDURE FOR SENDING FAXES" (page 20) and then follow the steps below. Press the [OK] key. 9 Enter the sub-address (maximum 20 digits) with the numeric keys. WXYZ Press the [SPECIAL FUNCTION] key. DUPLEX SPECIAL FUNCTION DUPLEX SCAN DUPLEX SCAN 3 8 ACC. When the [SPECIAL FUNCTION] key is pressed, the special function selection screen appears.
Chapter04.fm 59 ページ ２００４年９月３０日 木曜日 午前９時１６分 TRANSMISSION USING F-CODES PRINTING A DOCUMENT RECEIVED TO AN F-CODE CONFIDENTIAL MEMORY BOX Faxes received in an F-code confidential memory box are printed out by entering the 4-digit print passcode (0000 to 9999) that was programmed when the box was created. Note 1 • Make sure that a Transaction Report is set to print out in the key operator programs so that you will be informed when a confidential document is received. (See "PRINT SELECTION (CONF.
Pegasus-E_Fax_Sec.book 60 ページ ２００４年９月２４日 金曜日 午後２時５１分 F-CODE RELAY BROADCAST TRANSMISSION The F-Code relay broadcast function allows the machine to act as a relay machine for a broadcast transmission. The end receiving machines are stored in the machine's F-Code relay memory box, and when the machine receives a relay request from another F-Code machine, it will relay the fax to all of the stored end receiving machines.
Pegasus-E_Fax_Sec.book 61 ページ ２００４年９月２４日 金曜日 午後２時５１分 TRANSMISSION USING F-CODES USING THE F-CODE RELAY BROADCAST FUNCTION (your machine is the relay machine) When a document is received from a relay request machine, the F-code relay broadcast function transmits the document to the end receiving machines using a memory box only if the sub-address and passcode sent by the relay request machine are correct. To create, edit, or delete an F-code relay group (box), see pages 76, 78 and 81.
Pegasus-E_Fax_Sec.book 5 62 ページ ２００４年９月２４日 金曜日 午後２時５１分 CONVENIENT METHODS OF USE This chapter explains convenient functions that can be used when sending a fax, connecting an extension phone, and other features that expand the scope of use of the fax machine. Please read those sections that are of interest to you. CONNECTING AN EXTENSION PHONE You can connect a telephone to the machine and use it as an extension phone to make and receive calls like any normal phone.
Pegasus-E_Fax_Sec.book 63 ページ ２００４年９月２４日 金曜日 午後２時５１分 CONVENIENT METHODS OF USE SETTING THE RECEPTION MODE The machine normally receives faxes automatically after ringing; however, when an extension phone is connected, you can set the reception mode to MANUAL. This will allow you to talk to the other party first and then receive a fax. This is convenient when you only have one telephone line and receive more voice calls than faxes.
Pegasus-E_Fax_Sec.book 6 64 ページ ２００４年９月２４日 金曜日 午後２時５１分 PROGRAMMING This chapter explains the procedures for programming auto dial keys (Rapid keys, Speed Dial numbers, and group keys), programs, and F-code operations, and how to print out lists of programmed information. PROGRAMMING Auto dial numbers (Rapid keys, Speed Dial numbers, and group keys), programs, and F-code operations are stored and edited at the operation panel of the machine.
Pegasus-E_Fax_Sec.book 65 ページ ２００４年９月２４日 金曜日 午後２時５１分 PROGRAMMING 3 Press the [OK] key. BACK OK [Storing Rapid keys and Speed Dial numbers] To store a Rapid key or Speed Dial number, follow steps 1 through 6 on pages 64 to 65 and then follow the steps below. 7 GHI 4 Select "DIAL" with the [ ] or [ ] key. ENTRY DIAL PROGRAM SUB ADD SETTING • If you are storing a Rapid key, press the Rapid key that you wish to use ([01] to [50]).
Chapter06.fm 66 ページ ２００４年１１月１１日 木曜日 午前１１時１分 PROGRAMMING 11 13 Press the [OK] key. OK 12 26 27 31 28 B 32 F 36 29 C 33 G 37 K • If you pressed the [START] key ( ), you will return to step 7. If you wish to store another Rapid key or Speed Dial number, repeat steps 7 to 13. If you have finished storing auto-dial numbers, press the [BACK] key. • If you pressed the [OK] key, go to the appropriate page for the option that you wish to program.
Pegasus-E_Fax_Sec.book 67 ページ ２００４年９月２４日 金曜日 午後２時５１分 PROGRAMMING 3 Enter a sub-address (maximum 20 digits) with the numeric keys. OK ABC DEF GHI JKL MNO PQRS TUV WXYZ SUB ADDRESS [Chain Dialing] To set an auto-dial number as a Chain Dial number, complete steps 1 through 13 on pages 64 to 66 and then follow the steps below. Note :123 @.-_ FUNCTION ACC. #-C READ-END Characters that can be entered are numbers, " ", "#", and spaces.
Chapter06.fm 68 ページ ２００４年９月３０日 木曜日 午前９時１４分 PROGRAMMING [Transmission speed setting] [International transmission mode setting] To set the transmission speed, complete steps 1 through 13 on pages 64 to 66 and then follow the steps below. To set the international transmission mode, complete steps 1 through 13 on pages 64 to 66 and then follow the steps below.
Pegasus-E_Fax_Sec.book 69 ページ ２００４年９月２４日 金曜日 午後２時５１分 PROGRAMMING [Storing a group key] 5 To store a group key, follow steps 1 through 6 on pages 64 to 65 and then follow the steps below. 1 • To store a Rapid key, press the Rapid key that you wish to use ([01] to [50]). Press a Rapid key ([01] to [50]). Press the Rapid key ([01] to [50]) that you wish to program as a group key. If you press a Rapid key that 26 27 28 29 30 has already been programmed, A B C D E a warning message will appear.
Pegasus-E_Fax_Sec.book 70 ページ ２００４年９月２４日 金曜日 午後２時５１分 PROGRAMMING [Editing and deleting auto-dial numbers] To edit or delete an auto-dial number, follow steps 1 through 6 on pages 64 and 65 and then follow the steps below. • To edit a Speed Dial number, press the [SPEED] key and then enter the Speed Dial number (000 to 299) that you wish to edit with the numeric keys.
Pegasus-E_Fax_Sec.book 71 ページ ２００４年９月２４日 金曜日 午後２時５１分 PROGRAMMING 11 To finish the storing procedure, press the [START] key ( ). If you wish to program an option such as F-code, chain dialing, transmission speed, or international transmission mode, press the [OK] key. • If you pressed the [START] key ( ), go to step 5. If you wish to program another Rapid key or Speed Dial number, repeat steps 5 to 11. To exit, press the [BACK] key. Editing to that point will be completed.
Pegasus-E_Fax_Sec.book 72 ページ ２００４年９月２４日 金曜日 午後２時５１分 PROGRAMMING 3 Select "CHANGE" with the [ ] or [ ] key. 9 Edit the stored information. • To add a Rapid key or Speed Dial number, enter the Rapid key ([01] to [50]) or Speed Dial number that you wish to add. A key or number that is already 26 27 28 29 30 in the group cannot be added. GROUP CHANGE DELETE A B 31 32 F G 36 4 37 K Press the [OK] key.
Pegasus-E_Fax_Sec.book 73 ページ ２００４年９月２４日 金曜日 午後２時５１分 PROGRAMMING ● Deleting a group key 1 In step 3 on page 72, select "DELETE" with the [ ] or [ ] key. GH PQR GROUP CHANGE DELETE DUPLEX SPECIAL FUNCTION DUPLEX SCAN 2 Press the [OK] key. BACK OK GHI 3 Press the group key (one of Rapid keys [01] to [50]) that you wish to edit. 26 27 A 31 28 32 F 36 4 C 33 30 D 34 G 37 K 29 B H 38 I 39 L M E 35 J 40 N O Select "DELETE" with the [ ] or [ ] key. SBC CO.
Pegasus-E_Fax_Sec.book 74 ページ ２００４年９月２４日 金曜日 午後２時５１分 PROGRAMMING STORING, EDITING AND DELETING PROGRAMS You can store a transmission method*, cover sheet/message, transmission settings, dual pages, and/or resolution/exposure settings in a program. This will allow you to use the settings for a transmission by means of a simple operation (see "USING A PROGRAM" on page 47).
Pegasus-E_Fax_Sec.book 75 ページ ２００４年９月２４日 金曜日 午後２時５１分 PROGRAMMING 10 Select the program that you wish to store with the [ ] or [ ] key. PROGRAM TX TYPE COVER SHEET/MSG [ ]:CANCEL [START]:ENTER • A transmission method, cover sheet/message, resolution/exposure settings, dual pages, sender's name, and transmission settings can be stored. A transmission method must be stored. The storing procedure cannot be completed unless a transmission method is stored.
Pegasus-E_Fax_Sec.book 76 ページ ２００４年９月２４日 金曜日 午後２時５１分 PROGRAMMING, EDITING, AND DELETING F-CODE MEMORY BOXES The procedure for programming a box for F-code transmission is explained here. There are three types of F-code boxes: F-code public boxes (page 79), F-code confidential boxes (page 77), and F-code relay group boxes (page 78). F-code boxes are programmed, edited, and deleted as explained below.
Pegasus-E_Fax_Sec.book 77 ページ ２００４年９月２４日 金曜日 午後２時５１分 PROGRAMMING [PROGRAMMING AN F-CODE CONFIDENTIAL BOX] Follow the steps below to program an F-code confidential reception box. An F-code (sub-address and passcode) for F-code confidential reception and a print passcode to print out received faxes are programmed in each box. Up to 10 boxes can be programmed. To check the contents of a programmed box, print the following list: "PRINT - REPORT - SUB ADD SET LIST".
Pegasus-E_Fax_Sec.book 78 ページ ２００４年９月２４日 金曜日 午後２時５１分 PROGRAMMING [PROGRAMMING AN F-CODE RELAY GROUP] This procedure is used to program an F-code relay group box for relay broadcast of a received fax upon receipt of an F-code relay request. Up to 10 boxes can be programmed. An F-code (sub-address and passcode) for reception of an F-code relay request and the destinations to which the fax is to be relayed are programmed in each box.
Pegasus-E_Fax_Sec.book 79 ページ ２００４年９月２４日 金曜日 午後２時５１分 PROGRAMMING [PROGRAMMING F-CODE PUBLIC (POLLING MEMORY) BOXES] This setting is used to program a box to store document data for remote transmission when polled by a machine that supports F-Code communication. Up to 10 boxes can be programmed. To check the contents of a programmed box, print the following list: "PRINT - REPORT - SUB ADD SET LIST" (page 83).
Pegasus-E_Fax_Sec.book 80 ページ ２００４年９月２４日 金曜日 午後２時５１分 PROGRAMMING ● Editing an F-code confidential box 11 Select the name of the F-code confidential box that you wish to edit with the [ ] or [ ] key. GH PQR DUPLEX SPECIAL FUNCTION DUPLEX SCAN S.A. CONF. BOX SBC CO. — — — — — — — — — — — — [#]:LIST DETAIL If not all letters of the box name appear, press the key to display all letters. Press the key once again to return to the original screen.
Pegasus-E_Fax_Sec.book 81 ページ ２００４年９月２４日 金曜日 午後２時５１分 PROGRAMMING [EDITING AND DELETING F-CODE RELAY GROUPS] 9 14 OK Select "CHANGE" or "DELETE" with the [ ] or [ ] key. GH PQR S.A. RELAY GRP CHANGE DELETE 15 DUPLEX SPECIAL FUNCTION Press the [OK] key. 16 BACK Edit the sub-address and passcode (maximum 20 digits) with the numeric keys. • See steps 3 to 6 on page 67. • If you do not need to edit the sub-address and passcode, press the [OK] key and go to the next step.
Pegasus-E_Fax_Sec.book 82 ページ ２００４年９月２４日 金曜日 午後２時５１分 PROGRAMMING [EDITING/DELETING F-CODE PUBLIC BOXES] 9 14 Select "CHANGE" or "DELETE" with the [ ] or [ ] key. GH PQR S.A. MEM POLLING CHANGE DELETE OK 15 DUPLEX SPECIAL FUNCTION DUPLEX SCAN 10 Press the [OK] key. • See steps 3 to 6 on page 67. • If you do not need to edit the sub-address and passcode, press the [OK] key and go to the next step. Press the [OK] key.
Pegasus-E_Fax_Sec.book 83 ページ ２００４年９月２４日 金曜日 午後２時５１分 PRINTING LISTS OF PROGRAMMED INFORMATION, SETTINGS, AND COMMUNICATION ACTIVITY You can print lists showing programmed information, settings, and communication activity. The following lists can be printed. • ACTIVITY REPORT: This report shows information on your most recent transmissions and receptions, including communication time and the other party. • TIMER LIST: This list shows timer transmissions and recall mode jobs. • MEM.
Pegasus-E_Fax_Sec.book 84 ページ ２００４年９月２４日 金曜日 午後２時５１分 ENTERING CHARACTERS This section explains how to enter and edit characters for names of rapid dial numbers, Speed Dial numbers, and group keys, as well as account names, program names, and search characters for the address list. CHARACTERS THAT CAN BE ENTERED Characters that can be entered for names The following characters can be entered: • Up to 36 characters can be entered for a name.
Pegasus-E_Fax_Sec.book 85 ページ ２００４年９月２４日 金曜日 午後２時５１分 PROGRAMMING CHARACTER ENTRY KEYS To enter characters, use the character entry keys on the operation panel. The characters entered by each key and key functions are as follows.
Pegasus-E_Fax_Sec.book 86 ページ ２００４年９月２４日 金曜日 午後２時５１分 PROGRAMMING INITIAL PROCEDURE FOR ENTERING CHARACTERS Entering alphabetical characters (example: TPS) 1 Entering symbols 1 Open the Rapid key overlay. 47 Press the [SYMBOL] key. 48 49 V ENTER NAME W REDIAL/PAUSE 50 XYZ SYMBOL ! " # % & ' ( ) + , - . / : ; < = > ? @ [ \ 1/ 2 SP SPEED COMM. SETTING SYMBOL SPACE/– ABC To switch between upper case letters and lower case letters, press the [SHIFT] key.
Pegasus-E_Fax_Sec.book 87 ページ ２００４年９月２４日 金曜日 午後２時５１分 PROGRAMMING Entering special characters Special characters are entered with the Rapid key overlay opened. 1 Press the [SP] key. 44 45 R S 49 W E SPEC. CHARACTER T 50 XYZ SP SPEED COMM. SETTING SYMBOL SPACE/– 2 1/ 2 Select the special character that you wish to enter with the [ ][ ][ ][ ] keys. GH SPEC.
Pegasus-E_Fax_Sec.book 7 88 ページ ２００４年９月２４日 金曜日 午後２時５１分 TROUBLESHOOTING This chapter contains information to help you make efficient use of the fax features of the machine, including solutions to common problems. WHEN A TRANSACTION REPORT IS PRINTED The machine has been set to automatically print a transaction report to notify you of the result when a transmission is not successful or when the Broadcast transmission function is used.
Pegasus-E_Fax_Sec.book 89 ページ ２００４年９月２４日 金曜日 午後２時５１分 TROUBLESHOOTING Sending result Explanation XX-XX OK When group dialing, broadcast transmission, or F-code relay request transmission was performed, xxx- : Indicates total number of transmissions. xxx OK : Indicates completed transmissions. NO S ADD FUNC When an F-code transmission was attempted, (1) The other machine did not have the F-code function. (2) An F-code was not programmed in the other machine.
Chapter07.fm 90 ページ ２００４年９月３０日 木曜日 午前９時１７分 VIEWING THE COMMUNICATION ACTIVITY REPORT AT REGULAR INTERVALS (Communication activity report) Your machine keeps a record of the most recent 50 transactions (both transmissions and receptions) that were performed. The record includes the date of the transaction, the other party's name, the duration, and result. You can have the report automatically printed when the number of transactions exceeds 50, or at a specified time.
Pegasus-E_Fax_Sec.book 91 ページ ２００４年９月２４日 金曜日 午後２時５１分 TROUBLESHOOTING Message (alarm sounds) Toner is low. Add toner. Can not copy or print. Meaning of message Solution Toner is low. Replace the toner cartridge. "REPLACING THE TONER CARTRIDGES" in the "Operation manual (for general information and copier)" There is no toner. Replace the toner cartridge.
Pegasus-E_Fax_Sec.book 92 ページ ２００４年９月２４日 金曜日 午後２時５１分 PROBLEMS AND SOLUTIONS If you experience a problem with the fax function, first check the following table. This section describes problems related to the fax function. For problems related to general operation of the machine, see "TROUBLESHOOTING" in the "Operation manual (for general information and copier)". Problem The machine does not operate. Dialing is not possible. Cannot send a fax.
Pegasus-E_Fax_Sec.book 93 ページ ２００４年９月２４日 金曜日 午後２時５１分 TROUBLESHOOTING Problem Solution Page Were line conditions poor due to thunder or another reason? Try the transmission again. Were the resolution and exposure settings suitable? Check the resolution and exposure settings. "SELECTING RESOLUTION AND EXPOSURE SETTINGS" on page 17 White or black lines appear in the transmitted image.
Pegasus-E_Fax_Sec.book 8 94 ページ ２００４年９月２４日 金曜日 午後２時５１分 KEY OPERATOR PROGRAMS The key operator programs are used by the key operator (administrator of the machine) to customize certain features of the machine to better meet the needs of users. This section explains key operator programs for the fax features of the machine. For key operator programs that are for the copy function, print function, and network scanner function, see the respective manuals for those functions.
Pegasus-E_Fax_Sec.book 95 ページ ２００４年９月２４日 金曜日 午後２時５１分 KEY OPERATOR PROGRAMS KEY OPERATOR PROGRAM MENU The key operator programs are accessed via the following menu structure. Refer to this menu when enabling or disabling the settings that are explained beginning on page 97. Some programs contain an additional level of settings (a settings screen).
Chapter08.fm 96 ページ ２００４年９月３０日 木曜日 午後１時９分 PROCEDURE FOR USING THE KEY OPERATOR PROGRAMS The key operator programs can be accessed from any mode (copy, fax, print, and scan mode). When the setting is completed, you will return to the previous mode. • Faxes cannot be sent or received while a key operator program is being used. • A key operator program cannot be used while a fax is being sent or received, while a voice call is being made, or while a received fax is being printed.
Chapter08.fm 97 ページ ２００４年９月２４日 金曜日 午後３時４１分 KEY OPERATOR PROGRAMS FOR THE FAX FUNCTION LIST PRINT/SET This program is used to print lists showing current key operator program settings and other programmed information. 1 Follow steps 1 through 6 of "INITIAL PROCEDURE" (page 96). 2 Select "LIST PRINT/SET" with the [ ] or [ ] key and then press the [OK] key. 3 Select "LIST SETTING" with the [ ] or [ key and then press the [OK] key.
Pegasus-E_Fax_Sec.book 98 ページ ２００４年９月２４日 金曜日 午後２時５１分 KEY OPERATOR PROGRAMS 2 Select "LIST PRINT/SET" with the [ ] or [ ] key and then press the [OK] key. 3 Select "LIST SETTING" with the [ key and then press the [OK] key. 4 Select "AUTO LISTING" with the [ ] or [ ] key and then press the [OK] key. 5 ] or [ INITIAL SETTING ] Select "AUTO PRINT REPT AT LIMIT (50)" with the [ ] or [ ] key and then press the [OK] key. • The setting is enabled and a checkmark appears in the checkbox.
Chapter08.fm 99 ページ ２００４年９月３０日 木曜日 午前９時１９分 KEY OPERATOR PROGRAMS 5 OWN PASSCODE SET Use this setting to program the fax number of the machine and the name of the user. The programmed name and number are printed at the top of each fax page you send. The number is also used as a passcode when performing polling reception "USING THE POLLING FUNCTION" (page 39). You can check your programmed name and number by printing out the "KEY OPE. LIST".
Chapter08.fm 100 ページ ２００４年１０月５日 火曜日 午後５時１４分 KEY OPERATOR PROGRAMS 3 Select "EXTENSION TEL" with the [ key and then press the [OK] key. ] or [ ] • The setting is enabled and a checkmark appears in the checkbox. • If this procedure is performed when the setting is enabled, the checkmark will be cleared and the setting disabled. DISTINCTIVE RING If multiple telephone numbers have been assigned to your telephone line, the number called can be identified by its ringing pattern.
Pegasus-E_Fax_Sec.book 101 ページ ２００４年９月２４日 金曜日 午後２時５１分 KEY OPERATOR PROGRAMS 6 3 Enter an account name (up to 18 characters) and then press the [OK] key. • See "ENTERING CHARACTERS" (page 84) for the procedure for entering letters. • Press the [OK] key to return to the screen of step 3. To program another account number, repeat steps 5 and 6. To exit, press the [BACK] key in step 5. • See "ENTERING CHARACTERS" (page 84) for the procedure for entering letters.
Pegasus-E_Fax_Sec.book 102 ページ ２００４年９月２４日 金曜日 午後２時５１分 KEY OPERATOR PROGRAMS 3 Select "DAYLIGHT SAVING TIME SETTING" with the [ ] or [ ] key and then press the [OK] key. • The setting is turned on and a checkmark appears in the checkbox. • If this procedure is performed when the setting is turned on, the checkmark is cleared and the setting turned off.
Pegasus-E_Fax_Sec.book 103 ページ ２００４年９月２４日 金曜日 午後２時５１分 KEY OPERATOR PROGRAMS PAGE COUNTER SET 2 This setting lets you select whether page numbers are printed at the top of fax pages by the receiving machine. The normal setting is to have page numbers printed. Select "SENDING FUNCTION" with the [ ] or [ ] key and then press the [OK] key. 3 Select "QUICK ON LINE TX" with the [ ] or [ ] key and then press the [OK] key. 1 Follow steps 1 through 6 of "INITIAL PROCEDURE" (page 96).
Pegasus-E_Fax_Sec.book 104 ページ ２００４年９月２４日 金曜日 午後２時５１分 KEY OPERATOR PROGRAMS RECALL SETTING (BUSY) RECALL SET (ERR) This program is used to set the number of recall attempts and the interval between recall attempts when a transmission is not successful due to the line being busy or other reason. Normally the machine is set to make 2 recall attempts at intervals of 3 minutes. If you do not wish to have recalling take place, set the number of attempts to "0" (steps 6 and 7).
Chapter08.fm 105 ページ ２００４年９月３０日 木曜日 午前９時１９分 KEY OPERATOR PROGRAMS RING TIMEOUT IN AUTO TX RCV. FUNCTION When sending a fax by automatic transmission (see "Storing transmission jobs (memory transmission)" on page 26), this setting lets you select the amount of time that the machine waits before breaking the connection when the other machine does not answer your machine's call. If the other machine does not respond within this set time, your machine will automatically break the connection.
Pegasus-E_Fax_Sec.book 106 ページ ２００４年９月２４日 金曜日 午後２時５１分 KEY OPERATOR PROGRAMS #OF RINGS AT. RX RECEIVED DATA PRINT CONDITION When the reception mode is set to auto, this program is used to select the number of rings on which the machine automatically receives a call and begins fax reception. (See "RECEIVING A FAX" on page 30.) Any number of rings from 0 to 9 can be selected. Normally "2" is selected. This setting determines the selection condition for paper when printing received documents.
Pegasus-E_Fax_Sec.book 107 ページ ２００４年９月２４日 金曜日 午後２時５１分 KEY OPERATOR PROGRAMS DUPLEX RECEPTION (Only on models with the two-sided printing function) This setting is used to select whether or not received faxes are printed on both sides of the paper. When two-sided printing is enabled and a fax that is two pages or longer is received (the pages must be the same size), the fax will be printed on both sides of the paper. 1 Follow steps 1 through 6 of "INITIAL PROCEDURE" (page 96). 2 Select "RCV.
Pegasus-E_Fax_Sec.book 108 ページ ２００４年９月２４日 金曜日 午後２時５１分 KEY OPERATOR PROGRAMS INDEX PRINT ANTI JUNK FAX This setting is used to have a black mark (index) printed at the top of each received fax page. The position of the mark is shifted with each fax reception, allowing you to easily distinguish where one fax reception ends and another begins. • Enable this function before receiving faxes. The function remains enabled until you disable it.
Pegasus-E_Fax_Sec.book 109 ページ ２００４年９月２４日 金曜日 午後２時５１分 KEY OPERATOR PROGRAMS 6 POLLING SECURITY These settings are used for the public box for regular polling memory. Note that they do not apply to F-code polling memory. (See "USING POLLING MEMORY" page 41.) POLLING SECURITY When performing polling memory (see "Polling security" on page 43), this setting is used to select whether any machine will be allowed to poll your machine, or only machines that have been programmed in your machine.
Pegasus-E_Fax_Sec.book 9 110 ページ ２００４年１１月４日 木曜日 午後５時２分 APPENDIX This chapter contains the specifications of the fax function and the index. SPECIFICATIONS For information on power requirements, power consumption, dimensions, weight, and other specifications that are common to all features of the machine, see "SPECIFICATIONS" in the "Operation manual (for general information and copier)".
Pegasus-E_Fax_Sec.book 111 ページ ２００４年９月２４日 金曜日 午後２時５１分 INDEX Symbols E #of rings at. RX .......................................................106 Earlier output .................................................... 30, 108 ECM ......................................................................... 27 Editing/deleting - F-code confidential boxes .................................. 79 - F-code public (polling memory) boxes ............... 82 - F-code relay groups ......................................
Pegasus-E_Fax_Sec.book 112 ページ ２００４年９月２４日 金曜日 午後２時５１分 M R Memory transmission ................................................26 Rapid dialing ............................................................ 18 Rcv. function .......................................................... 105 Read-end ................................................................. 21 Recall set (err)........................................................ 104 Recall setting (busy)............................................
Pegasus-E_Fax_Sec.book 113 ページ ２００４年９月２４日 金曜日 午後２時５１分 INDEX BY PURPOSE Advanced transmission methods Programming/settings Broadcast transmission.............................................34 Cover sheet/message function..................................46 Dual page scan .........................................................45 Forwarding function...................................................48 Own number sending ................................................44 Polling function - Polling ...
Pegasus-E_Fax_Sec.
Pegasus-E_Fax_Sec.
Pegasus-E_Fax_Sec.
Pegasus-E_Fax_Sec.
Pegasus-E_Fax_Sec.book 2 ページ ２００４年９月２４日 金曜日 午後２時５１分 AR-FX11 SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430-1163. www.sharpusa.com SHARP ELECTRONICS OF CANADA LTD.
