Specifications

AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-16
<List of set values>
66-9
Purpose Operation test, check
Function (Content) Used to check the output operation of the FAX
sound signals.
(Sound output IC operation check)
(Only when FAX is installed.)
Section FAX
Item Operation
Operation/Procedure A voice message is outputted.
(Send level is set with SW.)
Enter a number during execution to change the
kind of signal.
Press START to start sending a voice message.
Press CUSTOM SETTINGS to terminate.
SIMULATION 66-9
MESSAGE OUTPUT CHECK.(SOFT SW.) SELECT 1-20, AND PRESS
START.
1.NONE 2.PAUSE 3.MESSAGE1
4.MESSAGE2 5.MESSAGE3 6.MESSAGE4
7.MESSAGE5 8.MESSAGE6 9.MESSAGE7
10.MESSAGE8 11.MESSAGE9 12.MESSAGE10
13.MESSAGE11 14.MESSAGE12 15.MESSAGE13
16.MESSAGE14 17.MESSAGE15 18.ALARM
19.RINGER 20.EXT.TEL.RINGER
2
SIMULATION 66-9
MESSAGE OUTPUT CHECK.(SOFT SW.) SELECT 1-20, AND PRESS
START.EXECUTING...
1.NONE 2.PAUSE 3.MESSAGE1
4.MESSAGE2 5.MESSAGE3 6.MESSAGE4
7.MESSAGE5 8.MESSAGE6 9.MESSAGE7
10.MESSAGE8 11.MESSAGE9 12.MESSAGE10
13.MESSAGE11 14.MESSAGE12 15.MESSAGE13
16.MESSAGE14 17.MESSAGE15 18.ALARM
19.RINGER 20.EXT.TEL.RINGER
1
SIMULATION 66-9
MESSAGE OUTPUT CHECK.(SOFT SW.) SELECT 1-20, AND PRESS
START.EXECUTING...
1.NONE 2.PAUSE 3.MESSAGE1
4.MESSAGE2 5.MESSAGE3 6.MESSAGE4
7.MESSAGE5 8.MESSAGE6 9.MESSAGE7
10.MESSAGE8 11.MESSAGE9 12.MESSAGE10
13.MESSAGE11 14.MESSAGE12 15.MESSAGE13
16.MESSAGE14 17.MESSAGE15 18.ALARM
19.RINGER 20.EXT.TEL.RINGER
2
Press [CUSTOM SETTINGS] key.
Press [CUSTOM SETTINGS] key.
Select 2 and press [START] key.
Select 1 and press [START] key.
Same
display
1NONE NONE
2PAUSE PAUSE
3 MESSAGE1 MESSAGE1
4 MESSAGE2 MESSAGE2
5 MESSAGE3 MESSAGE3
6 MESSAGE4 MESSAGE4
7 MESSAGE5 MESSAGE5
8 MESSAGE6 MESSAGE6
9 MESSAGE7 MESSAGE7
10 MESSAGE8 MESSAGE8
11 MESSAGE9 MESSAGE9
12 MESSAGE10 MESSAGE10
13 MESSAGE11 MESSAGE11
14 MESSAGE12 MESSAGE12
15 MESSAGE13 MESSAGE13
16 MESSAGE14 MESSAGE14
17 MESSAGE15 MESSAGE15
18 ALARM ALARM
19 RINGER RINGER
20 EXT.TEL.RINGER EXT.TEL.RINGER
66-10
Purpose User data output, check (display, print)
Function (Content) Used to clear all data of image memory
(memory send, receive). Confidential data are
also cleared. (Only when FAX is installed.)
Section FAX
Item Data
Operation/Procedure The FAX image memory is cleared.
1) Select an item with 10 digit key pad and press
START. The following is executed and the
display returns to the initial state.
1: Image memory clear 2: Not clear
Only the Flash ROM area is cleared.
2) After completion of memory clear, reset.
SIMULATION 66-10
IMAGE MEMORY CLEAR.
ARE YOU SURE ?
1. YES
2. NO
1
SIMULATION 66-10
IMAGE MEMORY CLEAR. EXECUTING...
++++++
1
Press [START] key and start clear.
During execution of image memory clear, "+" is displayed.
When one block or a certain unit of area is cleared, "+" is added.
[06]SIMULATIONS ･ FAXSOFTWARESWITCH.fm 16 ページ ２００４年１０月２６日 火曜日 午後３時４４分