Specifications

AR-FX12 SIMULATIONS, FAX SOFTWARE SWITCH 6-37
35 5 Received document
output setup
Used to set whether all received data are collectively printed after completion of
all FAX reception or each page is printed after completion of reception of each
page.
0 Collectively
outputted
6 Not used 0
7 Automatic reduction/
dispose setup
Used to set whether automatic reduction is made so that the received data can
be printed on a page if reduced, when a document the size of which exceeds
the printable limit but is within the magnification ratio setup range of automatic
reduction is received.
0 Reduction Receive
setup
8 Reduction/dispose
setup when printing A3,
11X 17
Used to set whether the main scan width data are reduced or data on both
edges are disposed without reduction when A3 width document is received and
printed on 11x 17 inch paper. When set to "Reduction," the data are reduced by
94%.
1 Dispose
36 1-8 Setup of magnification
ratio in automatic
reduction
Used to set the percentage by which the received document is longer than the
printable length when automatic reduction print is enabled. The setup range is
85 - 100% by binary input of N into "N x 1% + 85%."When set to outside the
range, similar to the default value of 90%.
0 90%
0
0
0
0
1
0
1
37 1,2 Reception size
specification
(Indicates reception
capacity.)
Used to set the reception allowable document width of the machine which is
notified to the other party machine when receiving
When using the installed cassette, the max. cassette size as follows :
A3 width is used when no tray is set for Fax reception and printing and when the
cassette is open in case of installed cassettes.
0 By installed
cassette
0
3 11 x 17 paper reception
width setup
Used to set the reception allowable document width when 11 x 17 paper is
selected as FAX print paper.
0A3 width
4 Date/sender print
language selection
Used to set the date and FAX No. print (depending on the destination) at the top
of the document when transmitting. Date, FAX No. and fonts are switched.
0 Follows the
date format.
5 Default date/sender
print
Used to set whether the date and sender information are added at the top of the
transmitted document as default.
0 Added Send setup
6 Date/sender information
print position setup
Used to set the print position of the date/sender information at the top of the
transmitted document.
0 Outside the
document
Send setup
SW
No.
Bit
No.
Item Switch selection and function USA Initial value Key
operator
1: Each page is printed
after reception of each
page.
0: Collectively printed
after completion of all
FAX reception
1: Automatic reduction is not made and
data exceeding the printable limit are
disposed
.
0: Printed by
automatic
reduction
1: Dispose 0: Reduction
Bit No. 1 2
By installed cassette 0 0
A4 width 0 1
B4(A4•B4) width 1 0
A3(A3•B4•A4) width 1 1
A5/5.5 x 8.5R size A4 width
B5 size B4 width
A4/8.5 x 11 size A3 width
8.5 x 13/8.5 x 14 A3 width
B4 size B4 width
11 x 17 B4/A3 width
(Switch by FAX soft SW)
A3 size A3 width
1: B4(B4•A4) width 0: A3(A3•B4•A4) width
1: For North America 0: Follows the date format.
1:Not added 0:Added
1: Top of document 0: Outside of document
[06]SIMULATIONS ･ FAXSOFTWARESWITCH.fm 37 ページ ２００４年１０月２６日 火曜日 午後３時４４分