Specifications

AR-FX12 MACHINE OPERATION 7-6
B. Communication report codes
This code is indicated in the column of protocol communication report in a communication repot table and a communication management table when
communication is terminated.
<1>Communication report code XX (Top 2 digits): 00 ~ 99
<2>Communication report sub code 1: YY: Not used in this machine. (Always 00)
<3>Communication report sub code 2: ZZ: Indicates details of the report.
(1) Communication report code list 1
Means of communication: S = Send, R = Receive, P = Polling, B = Bulletin board
Report code
(Communication
result)
Display in the column of result Content of communication interruption
Means of
communication
0 ~ 31 Refer to the following
descriptions.
Depends on the point of communication interruption. For 16 or later, V.34 mode
communication. Refer to "(2) Communication report code list 2" in 7-6.
33 BUSY The calling side cannot establish connection with the remote party.
34 CANCEL A communication interruption command is made during sending/receiving.The
interruption key is pressed for interruption of input.
<S/R/P/B>
35 NG35XXXX Power is failed during sending/receiving. <S/R/P/B>
36 (No record paper)
37 (Record paper jam)
38 MEM. FULL Memory over during reception.Print is not made during reception in acting
reception inhibit.
<R/P><R/P>
39 (Number of paper unmatched)
40 (Relay not received)
41 LENGTH OVER The send data length of one page exceeds the limit (2m) in sending. <S/B>
42 LENGTH OVER The receive data length of one page exceeds the limit. <R/P>
43 (Communication) (OK) Speaking before data transmission
44 ORIGINAL ERROR A document jam occurs in direct sending. <S>
45 (Picture quality error)
46 NO RESPONSE The FAX signal from the remote party is not detected within T1 time. <S/P>
47 TX DECODE ERROR A decode error occurs in the FAX board. <S/B>
48 OK Normal end of communication Normal end of
communication
OK REPLY RECEIVE OK in internet FAX send with reception confirmation.
49 NO RX POLL The called side does not have polling function in polling reception. The called side
has no data to send.
<P><P>
50 RX POLL FAIL In polling reception, DCN is received for DTC.In polling sending, there is no send
data.
<P><B>
51 PASS # NG In poling sending, the allow number is not matched. In polling sending, the
system number is not matched.
<B><B>
52 (No confidential function in
remote party)
In confidential sending, the remote party does not have confidential function.
(Including other company's machines)
<1>The NSF signal has not "Confidential function" bit.
<2>The NSF is not a Sharp machine.
<S>
53 (Confidential not received) <1>In confidential sending, DCN is received for NSS. <S>
54 (Confidential BOX NO NG) <1>In confidential reception, a confidential box number which is not registered is
specified.
<R>
55 (No relay function in remote
party)
In relay command sending, the remote machine has no relay function.
(Including other company's machine)
<1>The NSF signal has not "Confidential function" bit.
<2>The NSF is not a Sharp machine.
<S>
56 NO REL RX <1>In relay command sending, DCN is received for NSS.
<2>In relay command reception, a remote station number which is not registered
is specified.
<3>In F code relay broadcasting, an F code relay command is received.
<S><R><R>
57 (Relay ID unmatched) <1>In relay command reception, the relay ID does not match. <R>
58 REJECTED In reception, data are sent from a remote machine of receive inhibit number.
Communication report XX (YY ZZ)
[07]MACHINEOPERATION.fm 6 ページ ２００４年１０月２６日 火曜日 午後３時４５分