AR-FX2 CODE: 00ZARFX2//A1E DIGITAL COPIER FAX EXPANSION KIT (For USA/Canada) AR-FX2 EXPANSION 2MB: AR-MM5 MEMORY 4MB: AR-MM6 MODEL 8MB: AR-MM7 CONTENTS [ 1 ] OUTLINE . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1 [ 2 ] SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . 2 - 1 [ 3 ] INSTALLING PROCEDURE . . . . . . . . . . . . . . . . . 3 - 1 [ 4 ] ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1 [ 5 ] SIMULATIONS . . . . . . . . . . . . . . . . . . . . . . . .
AR-FX2 [Copier mode] ● The START key indicator is lit. (Initial state.) [Fax mode] ● The display panel shows the following message (initial state): [Example] [1] OUTLINE A. Introduction This machine is the FAX expansion kit which is attached to the digital copier AR-160/200 series to provide facsimile functions. Note: 1) When attaching this machine, the SPF/RSPF, the LCD panel, and the motherboard are required.
AR-FX2 a. Fax Mode Initial State In the fax mode initial state, the messages similar to the following are shown on the display panel. Depending on user program settings, this display may differ slightly from yours. Date Day SEP 10 FRI STAND-BY Time % in memory 06:30 PM 100% b. Fax Function Features Enabled in Copier Mode ● Automatic fax reception ● Timer operations ● Programs that use timer operations ● Relay request ● Sending documents in memory from memory sending mode 3 sec. (Super G3/33600bps) 6 sec.
AR-FX2 5. Transmission function Dialing function Dialing function F code Timer mode Recall mode Rapid key dialing 35 other parties Speed dialing 150 other parties Group dialing 35 groups (including the other parties registered to rapid key dialing) Search dial Any of other parties registered to speed dialing, rapid key dialing and group dialing can be searched for using the first three letters.
AR-FX2 Book document transmission Transmission method In OC mode Received data override output NO Consecutive page transmission (page splitting) NO Transfer Transfer at occurrence of trouble YES (by user program setting) Transfer method By the special transmission key in case of a trouble Numberspecified receiving Receiving of only specified number enabled NO Receiving of only specified number disabled NO Confidential function Confidential receiving Sender Only Sharp machine having confi
AR-FX2 Number registration Speed dialing Transmission method Speed dialing keys + (000 to 149) + start key Rapid key dialing Number of other parties 35 other parties Number of other party’s number digits 40 digits Registered name 20 half-size letters (may be omitted) ∗ When omitted, register rapid key dialing number (01 to 35).
AR-FX2 9.
AR-FX2 2) Remove the operation panel. ● Remove the operation panel fixing screw, and remove the flat cable. [3] INSTALLING PROCEDURE 1. FAX expansion kit, LCD panel kit installation ● When installing the FAX expansion kit, the LCD panel kit is required.
AR-FX2 10) Attach the front cover to the copier. ● Warp the front cover by pressing the both sides, and attach it to the hinge arm of the machine. After attaching the paper tray, close the side cover and the bypass tray. 6) Install the Fax key unit. ● Connect the flat cable to the machine connector and fold the flat cable under the FAX key unit. Fix the Fax key unit with screws. Blue line-must be up 7) Stick the supplied label.
AR-FX2 14) Attach the FAX PWB. ● Fix it with (9) M3 screw (gold) packed together with the FAX expansion kit. 18) Attach the left cabinet to the copier. ● Attach the left cabinet using the screw, then pass the speaker harness through the hole of the PWB mounting frame and connect the speaker harness to the connector of the copier. M3x6 15) Attach the motherboard.
AR-FX2 21) Attach the ground plate. ● Hang the hook, and fix with M3 screw (gold) packed together. 2. Expansion memory attachment (ARMM5, MM6, MM7) M3X6 1) Remove the FAX connector cover with a screwdriver. 2) Insert the memory card so that the model name is on the back. 3) Attach the FAX connector cover. (1) (3) (1) (2) (3) Power on position Power off position M3X6 22) Attach the rear cabinet of the machine.
AR-FX2 [4] ADJUSTMENTS Section Adjustment items Density section A SIM 46-12 B FAX mode density adjustment (Individual mode) SIM 46-14 - 46-16 A Dial test SIM 66-13 1 2 Communication section Adjustment procedures FAX mode density adjustment (Overall mode) B. FAX mode density adjustment (Individual mode) ( SIM 46-14 – 16) 1. Density section A.
AR-FX2 6) Start transmission from the line. 2. Communication section Note: These items are factory adjusted when shipping according to FCC standards. Therefore, do not change the setting in the market. H:xx L:yy 1:YES 2:NO SENDING DTMF A. Dial test ( SIM 66-13) (1) Dial pulse transmission test 1) Execute SIM 66-13 in FAX mode. 2) Execute the dial pulse mode according to the instructions on the LCD display.
AR-FX2 [5] SIMULATIONS B. FAX mode 1. Entering the simulation mode A. Copy mode The following key operations allow to enter the simulation mode from the copy mode. Clear key → Interruption key → “0” key → Interruption key → Main code → Start key → Sub code → Start key Main code Sub code 22 11 Fax related counter display 14 Fax ROM ver.
AR-FX2 Main code Sub code 26 1 Content Option switch display Operational description 1 6 7 Set range Used to display the installed options with LED on the operation panel.
AR-FX2 B. FAX mode Main code Sub code 22 11 FAX related counter display The current Fax related counters are displayed on the LCD. Display Copy quantity Transmission counter Reception counter Time Accumulated transmission time Accumulated reception time 14 FAX ROM Ver. Display The currently installed ROM version is displayed on the LCD.
AR-FX2 66 ● The following signals are sent to the line and the main body speaker. 04 0db: Signals are sent in 0db. Soft SW: Signals are sent in the level set with the soft SW.
AR-FX2 66 11 300bps signal send Used to send signals in 300bps. Display/Key operation 0db: Signals are sent in 0db. 1: No signal Soft SW: Signals are sent in the 2: 111111 level set with the soft switch. 3: 111110 4: 000000 5: 010101 6: 000001 13 Dial test Used to check dial pulses (10PPS), check the DTMF signal send, adjust the dial pulse make time, and adjust the DTMF signal send level. For adjustment procedures, refer to the previous descriptions.
AR-FX2 [6] SOFTWARE SWITCH DESCRIPTIONS 1. Software switch changing procedure 2. Details 1) Execute SIM 66-01 in the FAX mode. 2) Select “1.YES” in the FAX soft SW setup. 3) FAX soft SW No. input XX (2 digits: 10-keyinput) + START key 4) Select “1.YES” in the Soft SW content check. 5) Press the bit No. to be changed, and the bit No. is highlighted. 6) Select “1.YES” in the confirmation menu of change. 7) The change is completed, and the display returns to the soft SW select menu. SW NO. Data NO.
AR-FX2 User program No. SW NO. Data NO. SW2 1 Reserved 0 2 Reserved 0 3 Reserved 0 4 Reserved 5 Remote select No. setup 6 Item 7 8 Switch selection and contents of functions 1 2 Density default setup 3 5 6 Reserved 7 Size specification 8 Used to set the density (LED) after pressing C/A key or in auto clear operation to Auto, Light, Slightly light, Medium, Slightly data, and Dark.
AR-FX2 User program No. SW NO. Data NO. SW5 1 Reserved 0 2 Reserved 0 3 Reserved 0 4 Reserved 5 Signal send level 6 Item 7 8 SW6 1 Switch selection and contents of functions ANSam (CED) signal send 3 CSI send 4 DIS reception check in G3 send 5 6 Used to set whether non-modulation carriers are sent or not in V.29 transmission. EOL detection timer Used to set the detection timer of EOL (End Of Line) in phase C reception.
AR-FX2 SW NO. Data NO. SW7 1 Item MH fixing Switch selection and contents of functions Used to fix the image data compression method in transmission to MH. However, when SW52-7 (V.34 mode function) is OFF or when SW52-7 (V.34 mode function) is ON in transmission, MH fixing is effective. This is because MMR function is indispensable in V.34 mode and the other party machine may perform checking. When SW52-7 (V.34 mode function) is ON in reception, this function is disabled.
AR-FX2 SW NO. Data NO. SW9 1 SW10 Item Communication record total time/total number of sheets print Switch selection and contents of functions Used to set whether total communication time and total number of sheets are recorded or not on the communication record table. 1.
AR-FX2 SW NO. SW13 Data NO. Item Switch selection and contents of functions 1 Reserved 0 2 Reserved 0 3 Call ring sound volume 4 Used to set the reception sound volume regardless of handset. SW13 Bit No. Silent Small Medium Large 3 0 0 1 1 Medium 1 Reserved 1 Reserved 0 7 Interface data output Interface broadcasting function Used to set whether the received document is outputted from the interface direction station when interface broadcasting direction is received. 1 V.
AR-FX2 SW NO. Data NO. SW15 1 2 Item Used to set the lower limit of busy tone detection time (ON time). Upper limit of busy tone detection time Used to set the upper limit of busy tone detection time (ON time). Reserved 4 Reserved 5 Modem speed (other than V.33 mode) 7 SW17 1 Reserved 2 External telephone connection 0 750 ms 0 0: 750 ms 0 0 Used to set the communication start speed other in a mode other than V.34 mode.
AR-FX2 SW NO. SW18 Data NO. Item Switch selection and contents of functions User program No. Initial value 1 Reserved 0 2 Reserved 0 3 Reception size specification (Shows reception capacity.) Used to set the receivable document width which is informed the other party when receiving a communication. The setup items are as follows: 11″ reception capacity setup Used to set the recording width of DIS signal when the set paper size is Ledger (11 × 17, main scanning 279.
AR-FX2 SW NO. Data NO. SW19 3 Item Output only in case of protocol monitor error Switch selection and contents of functions Effective only when SW19-1 is set to 1 (YES). Used to set whether protocol monitor is outputted only when a communication is not completed normally due to a communication error or it is outputted after completion of every communication.
AR-FX2 SW NO. SW21 Data NO. 1 2 3 4 SW22 SW23 SW24 Item Interval between the end of a communication and the next call Switch selection and contents of functions Used to set the time interval between the end of a communication and a call for the next communication. SW21 Bit No. Set range User program No.
AR-FX2 SW NO. Data NO. SW25 1 2 Item Auto reduction ratio setup 3 Used to set the auto reduction ratio when “Auto reduction print” is set to Enable. The set value is the min. reduction ratio. SW25 Bit No. Set range 4 SW26 Switch selection and contents of functions 10% 1 1 0 5 Reserved 0 6 Reserved 0 7 Reserved 0 8 Reserved 1 Read end sound 2 Reserved 3 Speaker sound volume setup 4 0 Used to set whether read end sound is made or not when read is completed.
AR-FX2 SW NO. SW28 SW29 Data NO. Item User program No. Initial value 1 Reserved 0 2 Reserved 0 3 Reserved 0 4 Reserved 0 5 Reserved 0 6 Reserved 0 7 Reserved 0 8 Standard reading setup Read mode setup in the standard mode 1: cm50% (Standard mode is read as Standard mode.) 0: Without cm50% (Standard mode is read as Fine mode.
AR-FX2 SW NO. Data NO. SW31 1 2 Item Report output (Transmission) Switch selection and contents of functions Used to set whether the communication report is outputted or not after completion of transmission (excluding sequential broadcasting, sequential send request, and interface broadcasting). SW31 Bit No.
AR-FX2 SW NO. Data NO. SW33 1 Item Page number print setup Switch selection and contents of functions Used to set whether the page number is added to the position where date and transmitter information are printed.
AR-FX2 User program No. SW NO. Data NO. SW37 1 Reserved 0 2 Reserved 0 3 Reserved 0 4 Reserved 0 5 Reserved 0 6 Reserved 1 7 Reserved 0 8 Reserved 1 1 Pause time setup SW38 2 Item 3 4 Switch selection and contents of functions Used to set the pause time. The set range is 1 sec to 15 sec by binary input. When set to 0, it is the same as 2 sec. SW38 Bit No.
AR-FX2 SW NO. Data NO. SW41 1 2 3 Item Number of recall times in case of busy state Switch selection and contents of functions Used to set the number of recall times in case of busy state of the other party or when call does not reach the other party. SW41 Bit No.
AR-FX2 SW NO. Data NO. SW45 1 Item F.A.S.T mode Switch selection and contents of functions Used to set YES/NO of the conformity for F.A.S.T 1: YES 2 3 4 Used to set the date format of LCD display, report descriptions, and the transmitter information. Time format Used to set the time format of LCD display, report descriptions, and the transmitter information.
AR-FX2 SW NO. Data NO. SW49 1 2 3 4 Item Time designation 2 (hour) print on the activity report Switch selection and contents of functions Used to set time designation 2 (hour) to be printed on the activity report. SW47 Bit No. Set range 00 0 Reserved 0 8 Reserved 1 Time designation 2 (min) print on the activity report SW48 Bit No.
AR-FX2 SW NO. Data NO. SW53 1 2 Item DTMF send level (High group) setup 3 Switch selection and contents of functions Used to set the DTMF signal send level (high group). The set range is 0 – 15 with binary input in the increment of 0.5dB. Send level = – (Set value + 16)/2 [dB] SW53 Bit No. 4 Set range 5 6 DTMF send level (Low group) setup 7 8 SW53 Bit No. Set range SW54 SW55 7 1 1 7 1 1 1 5 6 7 8 0 – 15 In the increment of 0.
AR-FX2 SW NO. SW57 SW58 Data NO. Reserved 0 Reserved 0 8 Reserved 0 1 V.34 3429 (Baud) Rate Mask Used to set whether 3429 is supported as the symbol rate in V.34 communication or not. V.34 3200 (Baud) Rate Mask Used to set whether 3200 is supported as the symbol rate in V.34 communication or not. V.34 3000(Baud) Rate Mask Used to set whether 3000 is supported as the symbol rate in V.34 communication or not. V.
AR-FX2 User program No. SW NO. Data NO.
AR-FX2 SW NO. SW67 Data NO. 1 2 Item Make time (10PPS) setup Switch selection and contents of functions Used to set the make time when dialing at 10PPS. The set range of N is 0 – 15 in binary input for the make time of (N +26 ms), which ranges from 26 to 41 ms. 40 ms 1 SW67 Bit No.
AR-FX2 SW NO. Data NO. SW72 1 Item EYE-Q check Switch selection and contents of functions Used to set whether TCF is checked or not in TCF reception. 1: EYE-Q check only SW73 SW74 SW75 0: "0" reception & EYE-Q check User program No.
AR-FX2 SW NO. SW76 SW77 SW78 SW79 Data NO. Item Switch selection and contents of functions User program No.
AR-FX2 [7] USER PROGRAMS 1. List Number Program Name Soft SW setup Function 101 DEPARTMENT CODE SETTING SW30-4 Set to restrict the use of the fax function to certain departments. 102 DIAL MODE SETTING SW44-1 ∼ 2 Set to select the type of phone line used for connection. 103 PAUSE TIME SETTING SW38-1 ∼ 4 Use to change the duration of pauses inserted in a recipient’s fax number. 104 SPEAKER VOLUME SETTING SW13-3 ∼ 4, SW26-3 ∼ 4 Set to increase or decrease the speaker volume.
AR-FX2 Number Program Name Soft SW setup Function Note IMAGE MEM. PRINT (LINE ERROR) SETTING SW1-7 139 AUTO LISTING SETTING SW19-7 SW47-1 SW48-1 SW49-1 SW50-1 140 PRINT STATION # IN RCVD DATA SETTING SW30-7 Set to choose where to print the date, your name, and your fax number on faxes you send. 141 PAGE COUNTER PRINT SETTING SW33-1 Set to print page numbers on faxes you send. 142 INDEX PRINT SW32-6 Set to print an index mark on the top of received faxes.
AR-FX2 Example [8] PRINTING 1=TIMER LIST PRESS START KEY 1. How to Print From the message display, select the type of list or report that you want to print. ● The activity report can be automatically printed by setting a user program. 1) In fax mode, press the REPORT key. The lower line of the display shows the type of list or report you are printing. The fax machine compiles the list you requested and automatically prints it.
AR-FX2 2. About Reports you can Print (Activity Report List) You can print out a list of faxes sent and received as well as the sender or recipient and the time of the operation, etc. With a user program you can print out the activity list at a certain time (2 times, maximum). (Example) P.01 ACTIVITY REPORT (SEND) SEP-10-1999 FRI 06:30 PM # XX RECEIVER'S NAME DATE START TIME COM.TIME PAGES XX XX TOTAL XX XX GRAND TTL XX XX SEP/10 XX:XX TYPE/NOTE DEPT FILE XXXXXXX XX P.
AR-FX2 Reception Result Explanation OK The reception completed successfully. P. FAIL There was a power failure during transmssion. MEM. FULL When using substitute reception, memory has become full. LENGTHOVER The received original was extra long. CONF. ERROR When receiving a confidential fax, the other fax machine entered a confidential box number that does not exist on your fax machine. RX NO POLL When polling 1) Your fax number has not been entered.
AR-FX2 (Telephone Number List) You can print out a list of number stored in rapid dialing and speed dialing. (Example) P. 01 TELEPHONE NUMBER LIST SEP-10-1999 FRI 06:30 PM RECEIVER'S FAX # RAPID/SPEED # INTL TX SET RECEIVER'S NAME RXX XXXXXXXXXXXXXX XXXX XXXXXXXXXXXXXX RXX XXXXXXXXXXXXXX XXXX XXXXXXXXXXXXXX SXXX XXXXXXXXXXXXXX XXXX XXXXXXXXXXXXXX ● The automatic dialing numbers are printed out in the following way. ∗ Rapid dial: R01, R02... ∗ Speed dial: S001, S002..
AR-FX2 (Passcode List) You can print a list of your fax information and polling security information. (Example) PASSCODE LIST SEP-10-1999 FRI 06:30 PM XXXX POLL SECURITY XXXX SYSTEM# ID# 01 XXXX 02 XXXX 03 04 05 06 07 08 09 10 PASSCODE# 01 XXXXXXXXXX 02 XXXXXXXXXX 03 04 05 06 07 08 09 10 01 RELAY ID# XXXXXXXXXXXX 02 03 04 05 06 07 08 09 10 SENDER'S N AME XXXXXXXXXXXXXXXXXX SENDER'S # XXXXXXXXXXXXXXXX FW. STA.
AR-FX2 (Department Usage List) You can only print out this list if auditing is turned on with a user program. Each time you print out the list, the data is erased. (Example) DEPARTMENT USAGE LIST SEP-10-1999 FRI 06:30 PM DEPT # DEPARTMENT N AME COM.
AR-FX2 D. Program operation [9] FIRMWARE VERSION UP PROCEDURE (1) Starting the program Double-click MFP.exe in the installed folder, or execute the program from the start menu. ∗ This program cannot be multi-started. When it is tried to be multistarted, an error message will be shown. (2) Descriptions of the main menu When MFP.exe is executed, the following main menu is displayed. 1.
AR-FX2 The following information of the inserted card is displayed. • Card information a. Kind of the card b. Version of the card c. DownLoad Program Version No. or registered data Program Version No. d. Write end • Data information a. Model name b. Main Program Version No. or registered data ID No. c. Write end The current operation mode of the application is displayed in the CardType section.
AR-FX2 7) After completion of writing, turn off the power of the notebook PC, and remove the card adapter. 8) Set the write protect switch to ON. 4. Writing to main PWB flash ROM 1) Necessary tools Small flash card (4MB) Panasonic BN-S04MF4C (UKOG0008QSZZ) 2) Select the FAX mode, then turn off the power. (Since LCD display is made in the FAX mode, be sure to select the FAX mode before turning off the power.) 3) Insert the download card into the expansion memory slot.
AR-FX2 [10] TROUBLE CODE LIST 1.
AR-FX2 2. Communication error codes Error code (Communication result) A. Error code identification Communication error xx (xxxx) (In print out, the communication error display is made. In FAX status check, “NGxxxxxx” is displayed. When transmission or reception is not executed normally due to disturbance in protocol signals and image signals by the trouble in the line, the code of 6 digits is displayed on the transmission result check menu (reception result check menu).
AR-FX2 Error code Final reception signal (Transmitting side) Final reception signal (Receiving side) 31 Timeout standby for turning off the reception control channel 91 Error in the first CC train 0 Abnormal signal Abnormal signal 92 Timeout standby for PPh 1 NSF, DIS NSS, DCS 93 Tone A/B detected in CC retrain 2 CFR NSC, DTC 94 Timeout standby for ALT 3 FTT EOP 95 Ach found 4 MCF EOM 96 FED OFF with CC data 5 PIP, PIN MPS 97 Timeout standby
AR-FX2 Error codes 2 Content of communication interruption Transmission/ Reception 01 Transmission length over Transmission 02 EOL time over Reception 03 Carrier detection time up Reception 04 Polarity reversion detection (in phase C) Transmission/ Reception 05 8 min over (in phase C) Transmission 06 Memory image decoding error Reception 07 Memory image decoding error Transmission 08 Time up between frames in phase C Transmission/ Reception 10 Communication reque
AR-FX2 CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to manufacturer’s instructions.
AR-FX2 COPYRIGHT © 1999 BY SHARP CORPORATION All rights reserved. Printed in Japan. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. Trademark acknowledgments All other trademarks and copyrights are the property of their respective owners.
