Manual

ManualsBrandsSharp ManualsPrintersAR-M208

• GETTING STARTED

• MAKING COPIES

• SPECIAL FUNCTIONS

• COPIER TROUBLE?

• GENERAL INFORMATION

• OPTIONAL EQUIPMENT

DIGITAL MULTIFUNCTIONAL

SYSTEM

OPERATION MANUAL

Page

CHINA

KS➀

812QSZZ

MODEL

AR-M208

Ar-M208_sec.book 1 ページ２００２年６月１３日　木曜日　午後２時３７分

Summary of content (128 pages)

PAGE 1
Ar-M208_sec.
PAGE 2
Ar-M208_sec.book 2 ページ２００２年６月１３日木曜日午後２時３７分 ➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣ FOR YOUR RECORDS ... To protect against loss or theft, record and retain for reference the copier’s serial number located on the back of the unit.
PAGE 3
Ar-M208_sec.book 1 ページ２００２年６月１３日木曜日午後２時３７分 2 OUTLINE OF THIS MANUAL 1. GETTING STARTED This chapter describes the basic information on the use of this copier. 2. MAKING COPIES This chapter describes the basic copying functions such as normal copying, reduction or enlargement, and exposure adjustments. 3. 4 GENERAL INFORMATION This chapter describes general information about the use of the copier and the loading of paper and toner. 6.
PAGE 4
Ar-M208_sec.book 2 ページ２００２年６月１３日木曜日午後２時３７分 CONTENTS Page CHAPTER 1 GETTING STARTED INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 COPIER INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 MAIN FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 5
Ar-M208_sec.book 3 ページ２００２年６月１３日木曜日午後２時３７分 CONTENTS Page CHAPTER 4 COPIER TROUBLE? STATUS MESSAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MISFEED REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ● Misfeed in the RSPF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ● Misfeed in the bypass tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ● Misfeed in the copier . . . . . . . . . . .
PAGE 6
Ar-M208_sec.
PAGE 7
Ar-M208_sec.book 5 ページ２００２年６月１３日木曜日午後２時３７分 1 CHAPTER 1 GETTING STARTED This chapter describes the basic information on the use of this copier. Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 ● CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 ● COPIER INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 ● MAIN FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 8
Ar-M208_sec.book 6 ページ２００２年６月１３日木曜日午後２時３７分 INTRODUCTION This copier has been designed to provide convenient copying features in a minimum amount of office space and with maximum operational ease. To get full use of all copier features, be sure to familiarize yourself with this manual and the copier. For quick reference during copier use, keep this manual in a handy location.
PAGE 9
Ar-M208_sec.book 7 ページ２００２年６月１３日木曜日午後２時３７分 CAUTIONS Follow the cautions below when using this copier. WARNING: 1 ● The ● Do fusing area is hot. Exercise care in this area when removing misfed paper. not look directly at the light source. Doing so may damage your eyes. CAUTION: ● The SAFETY PRECAUTIONS ● This Digital Copier is rated Class 1 and complies with 21 CFR 1040.10 and 1040.11 of the CDRH standards. This means that the copier does not produce hazardous laser radiation.
PAGE 10
Ar-M208_sec.book 8 ページ２００２年６月１３日木曜日午後２時３７分 COPIER INSTALLATION Improper installation may damage the copier. Please note the following during initial installation and whenever the copier is moved. CAUTION: If the copier is moved from a cool place to a warm place, condensation may form inside the copier. Operation in this condition will cause poor copy quality and malfunctions. Leave the copier at room temperature for at least 2 hours before use.
PAGE 11
Ar-M208_sec.book 9 ページ２００２年６月１３日木曜日午後２時３７分 COPIER INSTALLATION Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements (See page 97.). Also make certain the outlet is properly grounded. NOTE: Connect the copier to a power outlet which is not used for other electric appliances. If a lighting fixture is connected to the same outlet, the light may flicker. 12" (30 cm) A small amount of ozone is produced within the copier during operation.
PAGE 12
Ar-M208_sec.book 10 ページ２００２年６月１３日木曜日午後２時３７分 MAIN FEATURES 1 High-speed laser copying ● ● GETTING STARTED 2 High-quality digital image ● ● ● 3 First-copy time at 600 dpi is only 4.8 seconds (except when recovering from a power save mode or immediately after power on). Copying speed is 20 copies/min. at 600 dpi, which lends itself for business use, providing improvement in working efficiency. High-quality copying at 600 dpi is performed.
PAGE 13
Ar-M208_sec.book 11 ページ２００２年６月１３日木曜日午後２時３７分 MAIN FEATURES 4 Scan once/ Print many ● The copier is equipped with a memory buffer allowing the copier to scan an original once and make up to 999 copies of the scanned image. This improves workflow, reduces operating noise from the copier and reduces wear and tear on the scanning mechanism, which provides for a higher reliability. Printer features 6 Optional features ● ● ● ● ● 7 This copier can be used as a network laser printer.
PAGE 14
Ar-M208_sec.book 12 ページ２００２年６月１３日木曜日午後２時３７分 PART NAMES AND FUNCTIONS Exterior GETTING STARTED Document feeder tray (p. 26) Hold up to 40 originals. Original guides Ajust to the size of the originals. Right side cover (p. 74) Open to remove misfed originals. Feeding roller cover (p. 73) Open to remove misfed originals. Exit area Finished originals are output here. Platen glass (p. 24) Place an original to be copied here. USB interface connector Plug a USB interface cable into this connnector.
PAGE 15
Ar-M208_sec.book 13 ページ２００２年６月１３日木曜日午後２時３７分 PART NAMES AND FUNCTIONS Interior 1 GETTING STARTED Bypass tray paper guides (p. 42) Adjust to the width of the copy paper. Bypass tray (p. 41) Paper including special paper (such as transparency film) can be fed from the bypass tray. Bypass tray extension (p. 41) Pull out when feeding large paper such as 8-1/2" x 11"R, 8-1/2" x 14" and 11" x 17". Fusing unit release levers (p. 78) Lower to remove misfed paper. WARNING: The fusing unit is hot.
PAGE 16
Ar-M208_sec.book 14 ページ２００２年６月１３日木曜日午後２時３７分 PART NAMES AND FUNCTIONS Operation panel GETTING STARTED COPY key and indicator (p. 84, 92) Press to select the COPY mode. Press and hold during standby or during warmup to display the total output count and the quantity of toner remaining. Mode keys and indicators Use these keys when relevant components are installed. Copy quantity display Displays the specified copy quantity during standby and displays the copy countdown as copies are made.
PAGE 17
Ar-M208_sec.book 15 ページ２００２年６月１３日木曜日午後２時３７分 PART NAMES AND FUNCTIONS 1 Ready to copy. 81/2 11 100% 81/2 11 AUTO IMAGE key (p. 37) Press for automatic copy ratio selection. 2-SIDED COPY key (p. 28) Press to select the 1-sided to 1-sided, 1-sided to 2-sided, 2-sided to 2-sided or 2-sided to 1-sided copy mode. OUTPUT key (p. 49) Press to select the sort, group or staple sort* mode. * To select the staple sort mode, an optional finisher must be installed.
PAGE 18
Ar-M208_sec.book 16 ページ２００２年６月１３日木曜日午後２時３７分 POWER ON AND OFF The power switch is located on the left side of the copier. Power on Turn the power switch to the "ON" position. Power on GETTING STARTED Power off ● When the power switch is turned to the "ON" position, the message "System check." will appear in the message display and warm-up will start.
PAGE 19
Ar-M208_sec.book 17 ページ２００２年６月１３日木曜日午後２時３７分 POWER ON AND OFF Initial settings The copier assumes the initial settings when it is first turned on, when the CLEAR ALL (CA) key is pressed, or a preset time (auto clear time) after the last copy is made in any mode. The initial settings that appear in the display are shown below. Ready to copy.
PAGE 20
Ar-M208_sec.book 18 ページ２００２年６月１３日木曜日午後２時３７分 FUNCTION ICONS The following function icons will be indicated on the setting screen of each copier function.
PAGE 21
Ar-M208_sec.book 19 ページ２００２年６月１３日木曜日午後２時３７分 FUNCTION REVIEW The current settings of copier functions that have been selected can be viewed in the display. ● The XY ZOOM and TRANSPARENCY functions cannot be viewed on the function review screen. 1 Press the JOB STATUS key. 2 Use the ● The 1 review screen will appear. GETTING STARTED and keys to select a function. FUNCTION REVIEW DUAL PAGE COPY ● The setting for the selected function will appear in the display.
PAGE 22
Ar-M208_sec.book 20 ページ２００２年６月１３日木曜日午後２時３７分 AUDITING ACCOUNTS If this copier has been programmed in the auditing mode, it will not perform copier functions until an assigned 5-digit account number has been entered. ★ KEY OPERATOR See page 17 of the KEY OPERATOR'S GUIDE for setting the auditing mode.
PAGE 23
Ar-M208_sec.book 21 ページ２００２年６月１３日木曜日午後２時３７分 AUDITING ACCOUNTS 2 When copying is completed, press the AUDIT CLEAR key. 1 Please see your key operator for assistance. ★KEY OPERATOR security. See page 19 of the KEY OPERATOR'S GUIDE for account number 21 GETTING STARTED NOTE: If an unassigned number is entered, "Enter your account number." will appear again in the display, indicating that the number was not accepted.
PAGE 24
Ar-M208_sec.
PAGE 25
Ar-M208_sec.book 23 ページ２００２年６月１３日木曜日午後２時３７分 CHAPTER 2 2 MAKING COPIES This chapter describes the basic copying functions such as normal copying, reduction or enlargement, and exposure adjustments. Page FROM THE PLATEN GLASS. . . . . . . . . . . . . . . . . . . . 24 ● COPYING FROM THE RSPF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 About reversing single pass feeder (RSPF). . . . . . . . . . . . . . . . . . 26 Using the RSPF . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 26
Ar-M208_sec.book 24 ページ２００２年６月１３日木曜日午後２時３７分 COPYING FROM THE PLATEN GLASS The basic copying procedure is described below. ● Image loss (max. 5/32" (4 mm)) can occur at the leading and trailing edges of the copies. Also image loss (max. 1/8" (3 mm)) can occur along the other edges of the copies. NOTE: If the copier has been programmed in the auditing mode, enter a 5-digit account number. See page 20. 1 Place an original face down on the platen glass and align it with the original size scale.
PAGE 27
02B_sec.fm 25 ページ２００２年６月１３日木曜日午後５時３２分 COPYING FROM THE PLATEN GLASS 3 Ensure that the desired paper tray is selected. Ready to copy. 81/2 11 AUTO 100% 81/2 11 4 AUTO Set the number of copies using the numeric keys. MAKING COPIES ●A 2 single copy can be made even when "0" is displayed. the CLEAR (C) key to clear an entry if a mistake is made. ● Press 5 Press the START ( ) key. ● The number in the copy quantity display will decrease by 1 each time a copy is made.
PAGE 28
Ar-M208_sec.book 26 ページ２００２年６月１３日木曜日午後２時３７分 COPYING FROM THE RSPF About reversing single pass feeder (RSPF) The reversing single pass feeder (RSPF) hold up to 40 originals each for automatic document feeding. If the RSPF is being used, two-sided originals can be copied automatically without having to manually turn them over. Acceptable originals Up to 40 originals ranging from 5-1/2" x 8-1/2" to 11" x 17" and from 15 lbs. to 23 lbs. can be used. The total aggregate thickness must not exceed 5/32".
PAGE 29
Ar-M208_sec.book 27 ページ２００２年６月１３日木曜日午後２時３７分 COPYING FROM THE RSPF 3 Set the originals face up in the document feeder tray. ● The original size will be indicated in the display, and the paper tray with the corresponding paper size will be automatically selected. ★KEY OPERATOR The auto paper select function can be disabled using a key operator program. If this function has been disabled, use the PAPER SELECT key to select the desired paper tray. See page 15 of the KEY OPERATOR'S GUIDE.
PAGE 30
Ar-M208_sec.book 28 ページ２００２年６月１３日木曜日午後２時３７分 TWO-SIDED COPYING Two-sided copies can be made by manually placing originals on the platen glass as described in the procedure below. Fully automatic two-sided copies can be made from one-sided originals. Additionally, fully automatic two-sided copying of two-sided originals or one-sided copying of two-sided originals can be made.
PAGE 31
Ar-M208_sec.book 29 ページ２００２年６月１３日木曜日午後２時３７分 TWO-SIDED COPYING 3 Use the ● Also and keys to select one-sided to two-sided copying. the 2-SIDED COPY key can be used to select a 2-sided copy mode. COPY MODE 1 to 1 1 2 1 to 2 2 2 2 to 2 BINDING CHANGE OFF 2 4 Use the or the OK key. key to select binding change if desired. Then, press MAKING COPIES ● The image of one side can be rotated 180º using the image rotation feature.
PAGE 32
Ar-M208_sec.book 30 ページ２００２年６月１３日木曜日午後２時３７分 TWO-SIDED COPYING 2 Press the 2-SIDED COPY key. ● The 2-sided copy mode selection screen will appear. COPY MODE 1 to 1 1 to 2 3 Use the 4 Use the OK key. ● Also and keys to select one-sided to two-sided copying. the 2-SIDED COPY key can be used to select a 2-sided copy mode. MAKING COPIES or key to select binding change if desired.
PAGE 33
Ar-M208_sec.book 31 ページ２００２年６月１３日木曜日午後２時３７分 TWO-SIDED COPYING 7 Place the second original face down on the platen glass and press the START ( ) key again. ● To stop a copy run during duplex copying, press the CLEAR (C) key. cancel the 2-sided copy mode, press the 2-SIDED COPY key, select the one-sided to one-sided mode, and press the OK key. ● If an uneven number of originals are being copied, press the READ-END key after the last original is scanned. The last copy will be output single-sided.
PAGE 34
Ar-M208_sec.book 32 ページ２００２年６月１３日木曜日午後２時３７分 TWO-SIDED COPYING 3 Use the and keys to select two-sided to two-sided copying and press the OK key. ● Also the 2-SIDED COPY key can be used to select a 2-sided copy mode. COPY MODE 1 to 1 1 2 1 to 2 2 2 2 to 2 4 Set the number of copies and press the START ( ) key. MAKING COPIES ● Be sure not to touch the originals as they move on the reversing tray. This may cause misfeeds.
PAGE 35
Ar-M208_sec.book 33 ページ２００２年６月１３日木曜日午後２時３７分 TWO-SIDED COPYING 2 Press the 2-SIDED COPY key. ● The 2-sided copy mode selection screen will appear. COPY MODE 1 to 1 1 2 1 to 2 2 2 2 to 2 2 3 Use the and keys to select two-sided to one-sided copying. MAKING COPIES COPY MODE 1 2 1 to 2 2 2 2 to 2 2 1 2 to 1 BINDING CHANGE OFF 4 Use the OK key. or key to select binding change if desired. Then, press the ● The image of one side can be rotated 180º using the image rotation feature.
PAGE 36
Ar-M208_sec.book 34 ページ２００２年６月１３日木曜日午後２時３７分 EXPOSURE ADJUSTMENT This copier has four exposure modes to choose from: AUTO, TEXT, TEXT/PHOTO, and PHOTO. Auto This is the standard initial setting for this copier. In this mode, the characteristics of an original being copied are "read" by the exposure system, and exposure adjustments are made automatically. This optimizes the contrast of the copied images by reducing the effect of colored or shaded background areas.
PAGE 37
Ar-M208_sec.book 35 ページ２００２年６月１３日木曜日午後２時３７分 EXPOSURE ADJUSTMENT 3 Use the ● Copy and keys to adjust the copy density as desired. density cannot be adjusted manually in the AUTO exposure mode. EXPOSURE AUTO AUTO TEXT TEXT/PHOTO 2 4 Press the OK key. return to the AUTO mode, press the EXPOSURE key, use the "AUTO", and press the OK key.
PAGE 38
Ar-M208_sec.book 36 ページ２００２年６月１３日木曜日午後２時３７分 REDUCTION/ ENLARGEMENT/ZOOM Reduction and enlargement ratios can be selected either automatically with the AUTO IMAGE key or manually with the COPY RATIO key. The zoom function enables precise copy ratio selection from 25% to 400% in 1% increments. NOTE: When using the RSPF, the zoom range is 50% to 200%. Automatic selection ● When the auto image function is enabled, the reduction or enlargement ratio cannot be selected manually.
PAGE 39
Ar-M208_sec.book 37 ページ２００２年６月１３日木曜日午後２時３７分 REDUCTION/ENLARGEMENT/ZOOM 3 Press the AUTO IMAGE key. ● The 4 Enter the number of copies and press the START ( ) key. ● To cancel the automatic reduction/enlargement mode, press the AUTO IMAGE key again. ● When copying from a RSPF, the automatic reduction/enlargement feature will be effective only for the current copy run. 37 2 MAKING COPIES copy ratio will be automatically set.
PAGE 40
Ar-M208_sec.book 38 ページ２００２年６月１３日木曜日午後２時３７分 REDUCTION/ENLARGEMENT/ZOOM Manual selection 1 Place an original on the platen glass and close the platen cover. Document feeder tray 2 Press the COPY RATIO key. ● The copy ratio adjustment screen will appear. MAKING COPIES COPY RATIO 121% 100% 95% ZOOM 100% 3 AUTO Use the and keys to select a preset copy ratio or use the keys to select a zoom ratio. and A.Preset reduction ratios are: 95%, 77%, 64%, 50%, and 25%. B.
PAGE 41
Ar-M208_sec.book 39 ページ２００２年６月１３日木曜日午後２時３７分 REDUCTION/ENLARGEMENT/ZOOM 4 Press the OK key. ● The display will return to the basic screen. Ensure that the desired paper tray is selected. 6 Set the number of copies and press the START ( ● If the auto paper select function has been enabled, the appropriate copy paper size will have been automatically selected based on the original size and the selected copy ratio.
PAGE 42
Ar-M208_sec.book 40 ページ２００２年６月１３日木曜日午後２時３７分 ROTATION COPYING If rotation of original image is enabled using a key operator program, the image of the original will rotate when the orientation of the original does not match that of the copy paper. Rotation copying will function only if the auto paper select mode or the auto image mode has been selected.
PAGE 43
Ar-M208_sec.book 41 ページ２００２年６月１３日木曜日午後２時３７分 BYPASS FEED (special paper) The bypass tray must be used to feed special papers such as transparency film and labels but can also be used to feed standard copy paper. Acceptable paper for copying from the bypass tray Weight Capacity (21 lb. bond paper) Special paper Ordinary paper: 5-1/2" x 8-1/2" to 11" x 17" 14 lbs. to 34 lbs.
PAGE 44
Ar-M208_sec.book 42 ページ２００２年６月１３日木曜日午後２時３７分 BYPASS FEED (special paper) 2 Set the paper guides to the copy paper width. 3 Insert the copy paper (print face down) all the way into the bypass tray. MAKING COPIES ● For the number of sheets which can be loaded into the tray, see the previous page. adding paper, first remove any paper remaining in the tray, combine it with the paper to be added and then reload as a single stack.
PAGE 45
Ar-M208_sec.book 43 ページ２００２年６月１３日木曜日午後２時３７分 BYPASS FEED (special paper) 5 Set the number of copies and press the START ( ) key. NOTE: The bypass tray can be used to copy onto the two sides of paper manually. When copying the second original, be sure to turn over the copy of the first original left to right and place it into the bypass tray as shown in the illustration.
PAGE 46
Ar-M208_sec.book 44 ページ２００２年６月１３日木曜日午後２時３７分 INTERRUPTING A COPY RUN INTERRUPT is used to interrupt a long copy run so that another job can be done. ● Two-sided and 2 in 1/ 4 in 1 copying jobs cannot be interrupted. ● Two-sided copying, sort, group, staple sort, job programs and 2 in 1/ 4 in 1 cannot be selected for interrupt copying. Key operator programs cannot be used in the interrupt mode. 1 Press the INTERRUPT ( ) key.
PAGE 47
Ar-M208_sec.book 45 ページ２００２年６月１３日木曜日午後２時３７分 INTERRUPTING A COPY RUN 5 When all INTERRUPT copies are finished, press the INTERRUPT ( ) key again to cancel the INTERRUPT mode, and remove the original used for interrupt copying. ● All 6 2 settings for the interrupted job will be automatically restored. Replace the original(s) for the interrupted job and press the START ( ) key to resume copying.
PAGE 48
Ar-M208_sec.
PAGE 49
Ar-M208_sec.book 47 ページ２００２年６月１３日木曜日午後２時３７分 CHAPTER 3 SPECIAL FUNCTIONS This chapter describes special copying functions including various image editing functions. Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Copying in the sort or group mode. . . . . . . . . . . . . . . . . . . . . . . . . 48 ● MARGIN SHIFT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 ● ERASE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 50
Ar-M208_sec.book 48 ページ２００２年６月１３日木曜日午後２時３７分 SORT/GROUP The copier has two sorter modes for different copying jobs: one sorts copies into sets matching the sequence of the originals and the second groups copies by originals. Sort mode Sets of copies will be sequentially delivered to the center tray. 1 2 3 3 1 2 3 2 1 1 2 3 Group mode Multiple copies of each original will be grouped in the center tray.
PAGE 51
Ar-M208_sec.book 49 ページ２００２年６月１３日木曜日午後２時３７分 SORT/GROUP 2 Press the OUTPUT key. ● The output mode selection screen will appear. SORT NO SORT 12 3 SORT 111 GROUP 3 Use the OK key. ● Also and keys to select the desired output mode and press the the OUTPUT key can be used to select an output mode. 3 Make all other desired copier selections and press the START ( key. ) ● If originals have been set in a RSPF in step 1, copying will start.
PAGE 52
Ar-M208_sec.book 50 ページ２００２年６月１３日木曜日午後２時３７分 SORT/GROUP 6 After all originals have been scanned, press the READ-END key. ● Copying will start. the memory becomes full of scanned original image data, a warning message will appear. Press the START ( ) key to start copying the data in memory or the CLEAR ALL (CA) key to cancel copying. ● The memory can be extended to a maximum of 272 MB to increase the capacity for storing image data by adding commercially available memory modules.
PAGE 53
Ar-M208_sec.book 51 ページ２００２年６月１３日木曜日午後２時３７分 MARGIN SHIFT The MARGIN SHIFT feature, in its initial setting, automatically shifts the text or image to increase the margin by approximately 1/2". Original Increased Copy margin A A Original A Copy A Original Copy A A Increased margin Increased margin ● The location of the margin to be increased can be selected at the left edge, the right edge or the top edge of the page. To select the location, see step 4 overleaf.
PAGE 54
Ar-M208_sec.book 52 ページ２００２年６月１３日木曜日午後２時３７分 MARGIN SHIFT 3 Press the OK key. ● The setting screen for MARGIN SHIFT will appear. MARGIN SHIFT OFF DOWN RIGHT 1/2 inch(1/4~1) 4 Use the and keys to select the shift direction and the to select the shift amount. ● Select ● Select SPECIAL FUNCTIONS 5 the shift direction from DOWN, RIGHT, and LEFT. the shift amount from 1/4", 1/2", 3/4", and 1". display will return to the basic screen.
PAGE 55
Ar-M208_sec.book 53 ページ２００２年６月１３日木曜日午後２時３７分 ERASE This copier has an edge erase mode and a center erase mode. Center erase Edge erase AB A A Edge + Center erase AB AB AB ● Edge erase can be used to eliminate shadow lines around the edges of copies which appear when thick paper or a book is used as an original. ● Center erase can be used to eliminate the shadow produced by the bindings of bound documents. ● Edge + center erase can be used together to eliminate both types of shadow lines.
PAGE 56
Ar-M208_sec.book 54 ページ２００２年６月１３日木曜日午後２時３７分 ERASE 4 Use the 5 Use the 6 Press the OK key. ● Select SPECIAL FUNCTIONS ● The 7 keys to select the desired erase mode. "EDGE", "CENTER" or "EDGE + CENTER". and keys to adjust the amount of erase if needed. display will return to the basic screen. Make all other desired copier selections and press the START ( key. ● To 54 and cancel the erase feature, select the erase feature again and select "OFF".
PAGE 57
Ar-M208_sec.book 55 ページ２００２年６月１３日木曜日午後２時３７分 DUAL PAGE COPY The DUAL PAGE COPY feature produces individual copies of two documents placed side by side on the platen glass. It is especially useful when copying books and other bound documents. Original Copy ● This feature can be used in the one-sided to two-sided copying mode. feature cannot be used with the 2 in 1 / 4 in 1, center erae, edge+center erase, enlargement or staple sort features.
PAGE 58
Ar-M208_sec.book 56 ページ２００２年６月１３日木曜日午後２時３７分 DUAL PAGE COPY 3 Use the key. and keys to select "DUAL PAGE COPY" and press the OK SPECIAL MODES MARGIN SHIFT ERASE DUAL PAGE COPY [OK]:OFF ON ●A check mark will appear to the left of "DUAL PAGE COPY", and the display will return to the basic screen. 4 Check to be sure that 8-1/2" x 11" sized copy paper is selected. 5 Make all other desired copier selections and press the START ( key.
PAGE 59
Ar-M208_sec.book 57 ページ２００２年６月１３日木曜日午後２時３７分 2 IN 1 OR 4 IN 1 The 2 in 1 or 4 in 1 feature is used to copy 2 or 4 originals, collectively in a specified order, onto one sheet. 2 in 1 copying Pattern Pattern Pattern Pattern Pattern Pattern Pattern 4 in 1 copying Pattern ● These features cannot be used with the dual page copying, XY zoom, erase or margin shift features. ● Copies can be made with or without the border lines.
PAGE 60
Ar-M208_sec.book 58 ページ２００２年６月１３日木曜日午後２時３７分 2 IN 1 OR 4 IN 1 3 Press the SPECIAL FUNCTION key. Then press the OK key. ● The SPECIAL MODES screen will appear. SPECIAL MODES MARGIN SHIFT ERASE DUAL PAGE COPY [OK]:ADJUST 4 Use the ● The and keys to select "2in1/4in1" and press the OK key. selection screen for 2 in 1 / 4 in 1 will appear. 2in1/4in1 OFF 2in1 4in1 [OK]:CHANGE----SPECIAL FUNCTIONS 5 Use the ● The and keys to select "2in1" or "4in1" and press the OK key.
PAGE 61
Ar-M208_sec.book 59 ページ２００２年６月１３日木曜日午後２時３７分 2 IN 1 OR 4 IN 1 7 Use the ● Select and keys to select a type of border line. the solid line, broken line or no border line. 2in1 PATTERN 1 BORDER 8 Press the OK key. 3 ● The Make all other desired copier selections and press the START ( key. ● The copy ratio will be calculated automatically. ● If a RSPF is used, copying will start after originals are ● If the platen glass is used, proceed to the next step. ) scanned.
PAGE 62
Ar-M208_sec.book 60 ページ２００２年６月１３日木曜日午後２時３７分 B/W REVERSE The B/W REVERSE feature is used to reverse black and white areas. Original Copy ● When the B/W REVERSE feature is selected, the exposure mode will be automatically set to the TEXT mode. Other exposure modes cannot be selected. Even if this feature is canceled, the TEXT mode will not automatically be canceled. 1 Place an original on the platen glass or in the document feeder tray. Document feeder tray 2 Press the SPECIAL FUNCTION key.
PAGE 63
Ar-M208_sec.book 61 ページ２００２年６月１３日木曜日午後２時３７分 B/W REVERSE 4 Make all other desired copier selections and press the START ( key. ) ● To cancel the B/W reverse feature, highlight "B/W REVERSE" with a check mark on the SPECIAL MODES screen and press the OK key.
PAGE 64
Ar-M208_sec.book 62 ページ２００２年６月１３日木曜日午後２時３７分 XY ZOOM The XY ZOOM feature allows the horizontal and vertical copy ratios to be changed independently. Example: Reduction only in the horizontal direction Original Copy ● This feature cannot be used with the 2 in 1 or 4 in 1 feature. use the XY ZOOM feature with the DUAL PAGE COPY feature, set the DUAL PAGE COPY feature first and then the XY ZOOM feature. (Enlargement cannot be set.) ● The copy ratios can be set from 25% to 400%.
PAGE 65
03sec.fm 63 ページ２００２年６月１３日木曜日午後７時３８分 XY ZOOM 3 Use the and keys to select "XY ZOOM" and press the OK key. ● The setting screen for XY ZOOM will appear. The copy ratio in the horizontal direction will be highlighted. XY ZOOM 121% ZOOM 100% X: 100% 95% Y: 100% [ ]:X Y 4 Use the , , direction. , and keys to change the copy ratio in the horizontal 3 the and keys to set the approximate ratio, then press the ratio or key to increase the ratio. 5 Press the ● The key to decrease the key.
PAGE 66
Ar-M208_sec.book 64 ページ２００２年６月１３日木曜日午後２時３７分 XY ZOOM 7 Press the OK key. ● The display will return to the basic screen. Ready to copy. 81/2 11R AUTO X121% Y 99% 81/2 14 AUTO 8 Ensure that the desired paper tray is selected. 9 Make all other desired copier selections and press the START ( key. ● If the auto paper select function has been enabled, the appropriate copy paper size will have been automatically selected based on the original size and the selected copy ratios.
PAGE 67
Ar-M208_sec.book 65 ページ２００２年６月１３日木曜日午後２時３７分 TRANSPARENCY The TRANSPARENCY feature is used to copy onto transparency film. ● When copying onto transparency film, use this feature to obtain better copy quality. When this feature is selected, the bypass tray will be automatically selected and "TRANSPARENCY" will appear in the paper size display. ● This feature cannot be used with duplex copying or staple sort copying. ● Recommended transparency film is SF-85A.
PAGE 68
Ar-M208_sec.book 66 ページ２００２年６月１３日木曜日午後２時３７分 TRANSPARENCY 4 Load transparency film into the bypass tray. 5 Make all other desired copier selections and press the START ( key. ● Load ● To transparency film one sheet at a time in the portrait orientation. ) cancel the transparency feature, highlight "TRANSPARENCY" with a check mark on the SPECIAL MODES screen and press the OK key.
PAGE 69
Ar-M208_sec.book 67 ページ２００２年６月１３日木曜日午後２時３７分 JOB MEMORY Nine frequently used job programs can be stored in each of nine storage registers. This is convenient for quick job recall without losing time manually reprogramming each aspect of a job. ● The following functions cannot be stored in the job memory: copy quantity, original size, document station (platen glass or document feeder tray), paper size, interrupt, extra image adjustment.
PAGE 70
Ar-M208_sec.book 68 ページ２００２年６月１３日木曜日午後２時３７分 JOB MEMORY 4 Select a program number from 1 to 9 using the numeric keys. ●A screen indicating that the settings have been stored will appear and then the display will return to the basic screen. ● The numbers with a check mark are program numbers which already contain job programs. If a program number containing a job program is entered, the message "Storage number selected is already used. Replace it?" will appear to confirm the selection.
PAGE 71
Ar-M208_sec.book 69 ページ２００２年６月１３日木曜日午後２時３７分 JOB MEMORY 3 Select a program number from 1 to 9 using the numeric keys. ● The numbers with a check mark are program numbers which contain job programs. If a checked number is entered, the message "Delete job program?" will appear to confirm the selection to delete the program. To delete the program, select "YES" with the and keys and press the OK key. ● If "NO" is selected, the previous screen will reappear.
PAGE 72
Ar-M208_sec.book 70 ページ２００２年６月１３日木曜日午後２時３７分 JOB MEMORY 3 Select a program number from 1 to 9 using the numeric keys. ● The numbers with a check mark are program numbers which contain job programs. If a checked number is entered, the settings for that job program will be recalled and the display will return to the basic screen. ● The recalled settings may be modified for a particular job run, but any changes made will not be stored in the job memory.
PAGE 73
Ar-M208_sec.book 71 ページ２００２年６月１３日木曜日午後２時３７分 CHAPTER 4 COPIER TROUBLE? This chapter describes how to remove misfed paper and how to remedy minor problems. Page MESSAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 ● MISFEED REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Misfeed in the RSPF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Misfeed in the bypass tray . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 74
Ar-M208_sec.book 72 ページ２００２年６月１３日木曜日午後２時３７分 STATUS MESSAGES If any of the following messages appears in the display, carry out the prescribed remedy. Message Remedy Maintenance required soon. Service by an authorized SHARP service technician will be required soon. Contact your service center as soon as possible. (This message will be displayed if the information key is pressed when the information ( ) icon is displayed.) Maintenance required. Call for service.
PAGE 75
Ar-M208_sec.book 73 ページ２００２年６月１３日木曜日午後２時３７分 MISFEED REMOVAL When a misfeed occurs, the copier will stop. The message "Clear paper path." will appear in the display along with an illustration showing paper misfeed locations. ● If paper becomes accidentally torn during removal, be sure to remove all pieces. Be careful not to damage the photoconductive drum. ● For misfeeds in optional equipment, see their respective sections of the operation manual.
PAGE 76
Ar-M208_sec.book 74 ページ２００２年６月１３日木曜日午後２時３７分 MISFEED REMOVAL Location B ● Open the document feeder cover, rotate the rollers in the direction indicated by the arrow to feed the misfed paper, and then gently remove the misfed original after closing the document feeder cover. Rollers ● If a small original such as 5-1/2" x 8-1/2" original has misfed or an original has misfed in the reversing tray, open the right side cover and gently remove the misfed original. Close the right side cover.
PAGE 77
Ar-M208_sec.book 75 ページ２００２年６月１３日木曜日午後２時３７分 MISFEED REMOVAL 2 Open and close the document feeder cover to cancel the misfeed display. ● You can also cancel the misfeed display by opening and closing the feeding roller cover or the right side cover. ● The number of originals that must be returned to the document feeder tray will be indicated in the display. 3 Return the indicated number of originals to the document feeder tray and press the START ( ) key to resume copying.
PAGE 78
Ar-M208_sec.book 76 ページ２００２年６月１３日木曜日午後２時３７分 MISFEED REMOVAL Misfeed in the copier Check the misfeed location. Remove the misfed paper following the instructions for each location in the illustration below. If the misfed paper is seen from this side, proceed to “C. Misfeed in the transport area”. If paper is misfed here, proceed to “A. Misfeed in the paper feed area”. A. Misfeed in the paper feed area COPIER TROUBLE? 76 1 Open the bypass tray and the side cover.
PAGE 79
Ar-M208_sec.book 77 ページ２００２年６月１３日木曜日午後２時３７分 MISFEED REMOVAL 3 Carefully remove the misfed paper. Turn the roller rotating knob in the direction of the arrow to assist in removing it. Roller rotating knob WARNING: The fusing unit is hot. Take care in removing paper. CAUTION: Do not touch the photoconductive drum (green portion) when removing the misfed paper. Doing so may damage the drum and cause smudges on copies. 4 Close the front cover and the side cover.
PAGE 80
Ar-M208_sec.book 78 ページ２００２年６月１３日木曜日午後２時３７分 MISFEED REMOVAL 3 Turn the roller rotating knob in the direction of the arrow. Roller rotating knob 4 Carefully remove the misfed paper. Lower the fusing unit release levers to allow easier removal. After removal, return the release levers to their operating positions. Fusing unit release levers WARNING: The fusing unit is hot. Take care in removing paper. CAUTION: not touch the photoconductive drum (green portion) when removing the misfed paper.
PAGE 81
Ar-M208_sec.book 79 ページ２００２年６月１３日木曜日午後２時３７分 MISFEED REMOVAL C. Misfeed in the transport area 1 Open the bypass tray and the side cover. 2 Use the green tabs on either side of the paper guide to rotate the guide open and remove the misfed paper. WARNING: The fusing unit is hot. Take care in removing paper. 3 Close the side cover. ● Confirm 4 that the misfeed display has been cleared. COPIER TROUBLE? Misfeed in the center tray 1 Remove the paper by pulling it into the center tray.
PAGE 82
Ar-M208_sec.book 80 ページ２００２年６月１３日木曜日午後２時３７分 MISFEED REMOVAL Misfeed in the upper paper tray Before opening the upper paper tray, be sure to open the bypass tray and the side cover and then perform steps 1 to 3 described in the "A. Misfeed in the paper feed area" section. 1 Pull out the upper paper tray and remove the misfed paper. 2 Close the paper tray. 3 Open and close the side cover to cancel the misfeed display.
PAGE 83
Ar-M208_sec.book 81 ページ２００２年６月１３日木曜日午後２時３７分 MISFEED REMOVAL 2 Remove the misfed paper. ● Be 3 careful not to tear the misfed paper during removal. If the misfed paper is not seen in step 2, pull out the lower paper tray and remove the misfed paper. ● Be careful not to tear the misfed paper during removal. 4 Close the paper tray. 5 Close the lower side cover. COPIER TROUBLE? ● Confirm 4 that the misfeed display has been cleared.
PAGE 84
Ar-M208_sec.book 82 ページ２００２年６月１３日木曜日午後２時３７分 MISFEED REMOVAL COPIER TROUBLE? 82 2 Gently pull the misfed paper out. 3 Close the upper exit area cover. ● Confirm that the misfeed display has been cleared.
PAGE 85
Ar-M208_sec.book 83 ページ２００２年６月１３日木曜日午後２時３７分 TROUBLESHOOTING Always check the message display whenever the copier stops during an operation or operation is not possible. Messages in the display will give you easy-to-follow directions. For other troubles not described by messages, check the chart below. Problem Solution Copier plugged in? Plug the copier into a grounded outlet as specified. See page 97. ● Power switch ON? Turn the power switch ON. See page 16. Copies are too dark or too light.
PAGE 86
Ar-M208_sec.book 84 ページ２００２年６月１３日木曜日午後２時３７分 TROUBLESHOOTING Problem Solution ● Platen glass or platen cover dirty? Clean regularly. See page 93. ● Original smudged or blotchy? Use a clean original. Black or white stripes appear on copies. ● Is the scanning window of a RSPF dirty? Clean the scanning window. Paper size for a paper tray cannot be set. ● Is the COPY indicator off? Press the COPY key to select the COPY mode. See page 14.
PAGE 87
Ar-M208_sec.book 85 ページ２００２年６月１３日木曜日午後２時３７分 CHAPTER 5 GENERAL INFORMATION This chapter describes general information about the use of the copier and the loading of paper and toner. Page ● PAPER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 Types and sizes of copy paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 Loading copy paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 88
Ar-M208_sec.book 86 ページ２００２年６月１３日木曜日午後２時３７分 PAPER Types and sizes of copy paper Types and sizes of copy paper which can be fed from the paper trays are shown below. For paper acceptable for feeding from the bypass tray, see page 41. Size Weight Capacity (21 lb. bond paper) 5-1/2" x 8-1/2" to 11" x 17" 15 lbs. to 21 lbs. 500 sheets A5 to A3 ● 5-1/2" x 8-1/2" and A5 copy papers cannot be fed from any tray except the uppermost tray.
PAGE 89
Ar-M208_sec.book 87 ページ２００２年６月１３日木曜日午後２時３７分 PAPER 3 Move the left guide to the appropriate slot as marked on the tray. 4 Fan the copy paper and insert it into the tray. ● When using 11" x 17" copy paper, store the left guide in the slot at the left front of the paper tray. Maximum height line ● Set the paper along the guides. tray holds up to 500 sheets of 21 lb. bond paper. ● Do not load paper above the maximum height line. ● The Push the paper tray firmly back into the copier.
PAGE 90
Ar-M208_sec.book 88 ページ２００２年６月１３日木曜日午後２時３７分 PAPER Changing the copy paper size in the tray Paper size setting can only be done while the machine is not operating and the COPY mode has been selected. ● B5 paper cannot be set for paper tray 2. 1 Press the SPECIAL FUNCTION key. ● The SPECIAL FUNCTION screen will appear. SPECIAL FUNCTION SPECIAL MODES ORIG. SIZE ENTER PAPER SIZE SET DISPLAY CONTRAST 2 Use the key.
PAGE 91
Ar-M208_sec.book 89 ページ２００２年６月１３日木曜日午後２時３７分 PAPER 5 Use the ● To 6 keys to select the paper size that has been set. change the size of another paper tray, press the key and then repeat steps 3 to 5. Press the OK key. ●A 7 and confirmation message for paper size setting will appear. Press the OK key. ● The specified paper size will be registered and the display will return to the basic screen.
PAGE 92
Ar-M208_sec.book 90 ページ２００２年６月１３日木曜日午後２時３７分 TONER CARTRIDGE REPLACEMENT The approximate quantity of toner remaining can be displayed by pressing and holding the COPY key during standby or warm-up. See page 92. When the quantity of toner remaining is less than 25%, obtain a new cartridge. When the toner cartridge replacement required icon ( ) appears in the display, replacement of the toner cartridge will be needed soon. If you press the information key, the message "Toner is low.
PAGE 93
Ar-M208_sec.book 91 ページ２００２年６月１３日木曜日午後２時３７分 TONER CARTRIDGE REPLACEMENT 3 Remove the new toner cartridge from the bag. Grasp the cartridge on both sides and shake it horizontally approximately 20 times. After shaking the cartridge, remove the tape. NOTE: Grasp the grip when holding the cartridge. Do not hold the cartridge by the shutter. Be sure to only shake the cartridge before the tape is removed. Approx.
PAGE 94
Ar-M208_sec.book 92 ページ２００２年６月１３日木曜日午後２時３７分 CHECKING THE TONER QUANTITY AND TOTAL OUTPUT COUNT The approximate quantity of toner remaining and the total output count can be displayed by the procedure below. The total count value displayed is the output count in the copy, print, and fax modes including the output count by the self-print function of the printer and facsimile features. 1 Press and hold the COPY key during standby or warm-up.
PAGE 95
Ar-M208_sec.book 93 ページ２００２年６月１３日木曜日午後２時３７分 CLEANING THE PLATEN GLASS AND RSPF Proper care is essential for clean, sharp copies. Please take a few minutes to regularly clean your copier. Stains or dirt on the platen glass or RSPF will also be copied. Wipe the platen glass, platen cover portion of the RSPF and the scanning window on the platen glass with a soft, clean cloth. ● If necessary, dampen the cloth with water. Do not use thinner, benzene, or similar volatile cleaning agents.
PAGE 96
Ar-M208_sec.book 94 ページ２００２年６月１３日木曜日午後２時３７分 CLEANING THE BYPASS TRAY PAPER FEED ROLLER If misfeeds occur frequently when feeding postcards, envelopes, thick paper, etc. through the bypass tray, wipe the paper feed roller at the feed slot of the bypass tray with a soft, clean cloth dampened with alcohol or water.
PAGE 97
Ar-M208_sec.book 95 ページ２００２年６月１３日木曜日午後２時３７分 DISPLAY CONTRAST ADJUSTMENT The contrast of the display can be adjusted as below. 1 Press the SPECIAL FUNCTION key. ● The SPECIAL FUNCTION screen will appear. SPECIAL FUNCTION SPECIAL MODES ORIG. SIZE ENTER PAPER SIZE SET DISPLAY CONTRAST 2 Use the OK key. ● The and keys to select "DISPLAY CONTRAST" and press the screen for contrast setting will appear. DISPLAY CONTRAST 3 Use the and keys to adjust the contrast.
PAGE 98
Ar-M208_sec.book 96 ページ２００２年６月１３日木曜日午後２時３７分 STORAGE OF SUPPLIES Standard supplies for this copier that are to be replaced by the user are copy paper, toner cartridge, and staple cartridge for the optional finisher (AR-FN5 N). For best copying results, be sure to use only SHARP Genuine Supplies which are designed, engineered, and tested to maximize the life and performance of SHARP copiers. Look for the Genuine Supplies label on the toner package.
PAGE 99
Ar-M208_sec.book 97 ページ２００２年６月１３日木曜日午後２時３７分 SPECIFICATIONS Type Desktop Copy system Dry, electrostatic transfer Originals Sheets, bound documents Original sizes Max. 11" x 17" Copy sizes Max. 11" x 17", Min. 5-1/2" x 8-1/2" Image loss: Max. 5/32" (4 mm) (leading and trailing edges), Max. 1/8" (3 mm) (along other edges) Copying speed (one-sided copying at 100% copy ratio) 600 dpi : 20 copies/min. (8-1/2" x 11") 00 copies/min. (8-1/2" x 11"R) 00 copies/min. (8-1/2" x 14") 00 copies/min.
PAGE 100
Ar-M208_sec.book 98 ページ２００２年６月１３日木曜日午後２時３７分 SPECIFICATIONS Noise level Sound Power Level LWA Copying: 6.3 [B], Standby: 3.9 [B] Sound Pressure Level LPA (bystander positions) Copying: 49 [dB (A)], Standby: 24 [dB (A)] Noise emission measurement in accordance with ISO 7779. Emission concentration (measurement according to RAL-UZ 62) Ozone: 0.02 mg/m3 or less Optional equipment Finisher (AR-FN5 N) Dust: 0.075 mg/m3 or less Styrene: 0.
PAGE 101
Ar-M208_sec.book 99 ページ２００２年６月１３日木曜日午後２時３７分 CHAPTER 6 OPTIONAL EQUIPMENT This chapter describes operating instructions for the Single Pass Feeder (AR-SP4), the Reversing Single Pass Feeder (AR-RP3), the Finisher (AR-FN5 N), the 500-Sheet Paper Feed Unit (AR-D11), and the 2 x 500-Sheet Paper Feed Unit (AR-D12). Page CONFIGURATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 ● FINISHER (AR-FN5 N) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 Part names . . . . . . .
PAGE 102
Ar-M208_sec.book 100 ページ２００２年６月１３日木曜日午後２時３７分 SYSTEM CONFIGURATION A number of options are available for the copier which allow you to configure a copier system to meet your particular needs. The options include the following.
PAGE 103
Ar-M208_sec.book 101 ページ２００２年６月１３日木曜日午後２時３７分 FINISHER (AR-FN5 N) The copier has two different finisher modes: one sorts copies into sets matching the sequence of the originals and the second groups copies by original. When an optional finisher (AR-FN5 N) is installed, the copier can automatically staple the sorted copies. Each collated set of copies or group of copies can be stacked offset from the previous set.
PAGE 104
Ar-M208_sec.book 102 ページ２００２年６月１３日木曜日午後２時３７分 FINISHER (AR-FN5 N) Specifications Tray capacity Top tray: 100 sheets Offset tray: 1,000 sheets (500 sheets for sizes larger than 8-1/2" x 11") Paper size Top tray: 5-1/2" x 8-1/2" to 11" x 17" Offset tray: 8-1/2" x 11" to 11" x 17" Paper weight Top tray: 15 lbs. to 21 lbs. Offset tray: 15 lbs. to 21 lbs. Offset Approx.
PAGE 105
Ar-M208_sec.book 103 ページ２００２年６月１３日木曜日午後２時３７分 FINISHER (AR-FN5 N) Finisher functions When the finisher is installed, the following four output modes can be selected: sort, staple sort, group, and non-sort. Press the OUTPUT key, use the and keys (or the OUTPUT key) to select the desired output mode, and then press the OK key. When copying in the sort or group mode, the output tray can be selected using the and keys and pressing the OK key.
PAGE 106
Ar-M208_sec.book 104 ページ２００２年６月１３日木曜日午後２時３７分 FINISHER (AR-FN5 N) Staple sort In the staple sort mode, 8-1/2" x 11", 8-1/2" x 11"R, 8-1/2" x 13", 8-1/2" x 14", and 11" x 17" (B5, A4, A4R, B4, and A3) size copies can be stapled. NOTE: Different size originals cannot be copied onto copy paper of their respective sizes in the staple sort mode. Using the RSPF 1 Set the originals in the document feeder tray.
PAGE 107
Ar-M208_sec.book 105 ページ２００２年６月１３日木曜日午後２時３７分 FINISHER (AR-FN5 N) 3 Use the 4 Set the number of copies and press the START ( ● Also and keys to select "STAPLE SORT" and press the OK key. the OUTPUT key can be used to select an output mode. ) key. ● When copying of a set is completed, the copies will be automatically stapled and delivered to the offset tray. Using the platen glass 1 Set an original face down on the platen glass with the corner to be stapled to the upper right position.
PAGE 108
Ar-M208_sec.book 106 ページ２００２年６月１３日木曜日午後２時３７分 FINISHER (AR-FN5 N) 2 Press the OUTPUT key. ● The output mode selection screen will appear. OUTPUT NO SORT 12 3 SORT STAPLE SORT EXIT CENTER OPTIONAL EQUIPMENT 106 3 Use the 4 Set the number of copies and press the START ( 5 Replace the scanned original with the next original and press the START ( ) key after it lights up. Repeat this step until all originals have been scanned. ● Also and keys to select "STAPLE SORT" and press the OK key.
PAGE 109
Ar-M208_sec.book 107 ページ２００２年６月１３日木曜日午後２時３７分 FINISHER (AR-FN5 N) 6 After all originals have been scanned, press the READ-END key. ● Copying will start and each set of completed copies will be automatically stapled and delivered to the offset tray. ● If the message "Can not continue. Remove paper from the offset tray." appears in the display, remove the copies from the offset tray. Staple cartridge replacement When the message "Add staples.
PAGE 110
Ar-M208_sec.book 108 ページ２００２年６月１３日木曜日午後２時３７分 FINISHER (AR-FN5 N) 4 Insert the new staple cartridge into the box until it clicks into place. ● Insert the new cartridge by aligning the arrows on the cartridge with those on the box. Check that the cartridge locks in place by pulling it slightly. ● A cartridge holds 3,000 staples. 5 Remove the tape from the cartridge. 6 Insert the staple box into the stapler unit until it clicks into place. 7 Close the stapler cover.
PAGE 111
Ar-M208_sec.book 109 ページ２００２年６月１３日木曜日午後２時３７分 FINISHER (AR-FN5 N) 2 Grasp the green portion of the staple box and remove the staple box from the stapler. 3 Raise the lever at the end of the staple box and remove the jammed staples. 4 Return the lever to its original position. 5 Insert the staple box into the stapler unit until it clicks into place. 6 Close the stapler cover.
PAGE 112
Ar-M208_sec.book 110 ページ２００２年６月１３日木曜日午後２時３７分 FINISHER (AR-FN5 N) Misfeed removal The copier will stop when a misfeed occurs. The message "Clear paper path." will appear along with a display of paper misfeed locations. When a misfeed is indicated for the finisher, follow the procedure below. OPTIONAL EQUIPMENT 110 1 Pull the handle of the stapler compiler cover and open the cover. 2 Remove any misfed paper from the transport area.
PAGE 113
Ar-M208_sec.book 111 ページ２００２年６月１３日木曜日午後２時３７分 FINISHER (AR-FN5 N) 4 Close the stapler compiler cover. 5 If the offset tray is being used, remove any misfed paper from the offset tray. 6 If the top tray is being used, open the top cover, remove any misfed paper, and close the top cover. ● Confirm that the misfeed display has been cleared.
PAGE 114
Ar-M208_sec.book 112 ページ２００２年６月１３日木曜日午後２時３７分 500-SHEET PAPER FEED UNIT (AR-D11)/2x500-SHEET PAPER FEED UNIT (AR-D12) These paper feed units provide the convenience of increased paper capacity for the copier and a greater choice of paper sizes readily available for copying. The AR-D11 contains one 500-sheet paper tray and the AR-D12 contains two 500-sheet paper trays.
PAGE 115
Ar-M208_sec.book 113 ページ２００２年６月１３日木曜日午後２時３７分 500-SHEET PAPER FEED UNIT (AR-D11)/2x500-SHEET PAPER FEED UNIT (AR-D12) Loading copy paper The method of loading copy paper for these paper feed units is the same as for the paper trays in the copier. See page 86. Changing the copy paper size in the tray The method of changing the copy paper size is the same as for the paper trays in the copier. See page 88. Misfeed removal The copier will stop when a misfeed occurs. The message "Clear paper path.
PAGE 116
Ar-M208_sec.book 114 ページ２００２年６月１３日木曜日午後２時３７分 500-SHEET PAPER FEED UNIT (AR-D11)/2x500-SHEET PAPER FEED UNIT (AR-D12) OPTIONAL EQUIPMENT 114 2 Pull out the paper tray which was in use. 3 Remove any misfed paper. 4 Close the paper tray. 5 Close the side cover. ● Confirm that the misfeed display has been cleared.
PAGE 117
Ar-M208_sec.book 115 ページ２００２年６月１３日木曜日午後２時３７分 INDEX 2 E 2 in 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 2x500-sheet paper feed unit . . . . . . . . . . . . . 112 Edge erase . . . . . . . . . . . . . . . . . . . . . . . . . . . Enlargement . . . . . . . . . . . . . . . . . . . . . . . . . . Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Exposure adjustment . . . . . . . . . . . . . . . . . . . . Exterior . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 118
Ar-M208_sec.book 116 ページ２００２年６月１３日木曜日午後２時３７分 INDEX N S Names – operation panel . . . . . . . . . . . . . . . . . . . . . . 14 – part. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Non-sort . . . . . . . . . . . . . . . . . . . . . . . . . . 49, 103 Sort . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48, 103 Special paper. . . . . . . . . . . . . . . . . . . . . . . . . . 41 Specifications – 500-sheet paper feed unit/2x500-sheet paper feed unit. . . . . . . . . . . .
PAGE 119
Ar-M208_sec.book 117 ページ２００２年６月１３日木曜日午後２時３７分 MATERIAL SAFETY DATA SHEET Date Issued : Apr. 2. 2001 MSDS NO. F-00981 1. PRODUCT AND COMPANY IDENTIFICATION Product Name : AR-270NT/270T/270ST/270FT/270NT-J/270ST-C/270FT-T (Black Toner) Supplier Identification : Sharp Corporation 22-22 Nagaike-cho, Abeno-ku, Osaka, Japan Local suppliers are listed below. Please contact the nearest supplier for additional information. (Country) U.S.A.
PAGE 120
Ar-M208_sec.book 118 ページ２００２年６月１３日木曜日午後２時３７分 5. FIRE -FIGHTING MEASURES Extinguishing Media : water, CO2, foam and dry chemicals Special Fire fighting Procedures : None Fire and Explosion Hazards : Toner material, like most finely divided organic powders, may form an explosive mixture. 6. ACCIDENTAL RELEASE MEASURES Personal Precautions : None Environmental Precautions: None Methods for Cleaning Up : Wipe off with paper or cloth. DO not use vacuum cleaner when a large amount is released.
PAGE 121
Ar-M208_sec.book 119 ページ２００２年６月１３日木曜日午後２時３７分 10. STABILITY AND REACTIVITY : Stability Hazardous Reactions : Conditions to avoid : Materials to avoid : Hazardous Decomposition Products : Further Information : Stable Dust explosion, like most finely divided organic powders. Electric discharge, throwing into fire. Oxidizing Materials CO, CO2 and NOx None 11.
PAGE 122
Ar-M208_sec.book 120 ページ２００２年６月１３日木曜日午後２時３７分 15. REGULATORY INFORMATION US Information TSCA (Toxic Substances Control Act): All chemical substances in this product comply with all applicable rules or order under TSCA.
PAGE 123
Ar-M208_sec.book 121 ページ２００２年６月１３日木曜日午後２時３７分 Date Issued : Apr. 2. 2001 MSDS NO. F-30981 1. PRODUCT AND COMPANY IDENTIFICATION Product Name : AR-270ND/270DV/270SD/270SD-C (Black Developer) Supplier Identification : Sharp Corporation 22-22 Nagaike-cho, Abeno-ku, Osaka, Japan Local suppliers are listed below. Please contact the nearest supplier for additional information. (Country) U.S.A.
PAGE 124
Ar-M208_sec.book 122 ページ２００２年６月１３日木曜日午後２時３７分 5. FIRE -FIGHTING MEASURES Extinguishing Media : water, CO2, foam and dry chemicals Special Fire fighting Procedures : None Fire and Explosion Hazards : Like most finely divided organic powders, it may form an explosive mixture. 6. ACCIDENTAL RELEASE MEASURES Personal Precautions : None Environmental Precautions: None Methods for Cleaning Up : Wipe off with paper or cloth. DO not use vacuum cleaner when a large amount is released.
PAGE 125
Ar-M208_sec.book 123 ページ２００２年６月１３日木曜日午後２時３７分 10. STABILITY AND REACTIVITY : Stability Hazardous Reactions : Conditions to avoid : Materials to avoid : Hazardous Decomposition Products : Further Information : Stable Dust explosion, like most finely divided organic powders. Electric discharge, throwing into fire. Oxidizing Materials CO, CO2 and NOx None 11.
PAGE 126
Ar-M208_sec.book 124 ページ２００２年６月１３日木曜日午後２時３７分 15. REGULATORY INFORMATION US Information TSCA (Toxic Substances Control Act): All chemical substances in this product comply with all applicable rules or order under TSCA.
PAGE 127
Ar-M208_sec.book 1 ページ２００２年６月１３日木曜日午後２時３７分 WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
PAGE 128
Ar-M208_sec.book 1 ページ２００２年６月１３日木曜日午後２時３７分 AR-M208 SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430-2135. www.sharp-usa.