Ar-M208_keyope_sec.
Ar-M208_keyope_sec.
Ar-M208_keyope_sec.book 1 ページ 2002年6月12日 水曜日 午後3時41分 This KEY OPERATOR'S GUIDE contains information about all programs for use by the key operator. The programs allow the key operator to tailor many functions of this copier for specific modes of operation. These programs can only be accessed after a key operator code number has been entered. Please familiarize yourself with this entire guide. Keep it handy, and refer to it for the information you need to keep the copier operating smoothly.
Ar-M208_keyope_sec.book 2 ページ 2002年6月12日 水曜日 午後3時41分 REGISTERING THE KEY OPERATOR CODE NUMBER A key operator code number must be registered before any key operator program can be used. The key operator must remember this number. Only this registered number will allow access to the key operator programs. 1 Press the SPECIAL FUNCTION key. ● The SPECIAL FUNCTION screen will appear. SPECIAL FUNCTION SPECIAL MODES ORIG. SIZE ENTER PAPER SIZE SET DISPLAY CONTRAST 2 Use the OK key.
Ar-M208_keyope_sec.book 3 ページ 2002年6月12日 水曜日 午後3時41分 REGISTERING THE KEY OPERATOR CODE 5 Press the OK key. ● The FUNCTION SETTING screen will appear with KEY OP. # CHANGE highlighted. 6 Press the OK key. 7 Choose a new 5-digit code number and enter it using the numeric keys. 8 Press the OK key. ● The code number will change from the factory setting (five zeros) to the new setting. This new setting will remain in effect until it is changed by the procedure above.
Ar-M208_keyope_sec.book 4 ページ 2002年6月12日 水曜日 午後3時41分 REGISTERING THE KEY OPERATOR CODE NUMBER 9 4 To continue with other key operator programs, use the and keys to select another program. To select a program of another category, press the BACK key and select the desired category. To exit the key operator program mode, press the CLEAR ALL (CA) key.
Ar-M208_keyope_sec.book 5 ページ 2002年6月12日 水曜日 午後3時41分 LIST OF KEY OPERATOR PROGRAMS A complete list of all key operator programs is provided below. These programs can only be accessed by first entering the key operator code number. Category Program Name Function setting Key Operator Number Change Timer setting Function Page No. Changes the key operator code number. 9 Exposure Adjust Lightens or darkens copies in the automatic exposure mode. 9 Margin Default Sets the initial margin shift values.
Ar-M208_keyope_sec.book 6 ページ 2002年6月12日 水曜日 午後3時41分 LIST OF KEY OPERATOR PROGRAMS Category Enable/disable Account control Other program 6 Program Name Function Page No. Disable Auto Paper Selection Prevents automatic paper selection. 15 Disable Auto Tray Switching Prevents automatic switching between the paper trays. 15 Disable Job Program Changing Prevents stored programs from being replaced or deleted.
Ar-M208_keyope_sec.book 7 ページ 2002年6月12日 水曜日 午後3時41分 USING THE KEY OPERATOR PROGRAMS 1 Press the SPECIAL FUNCTION key. ● The SPECIAL FUNCTION screen will appear. SPECIAL FUNCTION SPECIAL MODES ORIG. SIZE ENTER PAPER SIZE SET DISPLAY CONTRAST 2 Use the OK key. ● The and keys to select "KEY OPERATOR PRG." and press the following display will appear. Enter key operator code. KEY OPERATOR CODE: ----- 3 Enter the key operator code number.
Ar-M208_keyope_sec.book 8 ページ 2002年6月12日 水曜日 午後3時41分 USING THE KEY OPERATOR PROGRAMS 5 Use the key. ● Example: 6 Use the key. and keys to select the desired category and press the OK To see the number of copies per account, select "ACCOUNT CONTROL". and keys to select the desired program and press the OK ● Example: To see the number of copies per account, select "COPIES/ACCOUNT". some programs, a check box is displayed to the left of the program name.
Ar-M208_keyope_sec.book 9 ページ 2002年6月12日 水曜日 午後3時41分 KEY OPERATOR PROGRAMS FUNCTION SETTING The programs of this category are used to adjust various settings of copier functions. These programs can be selected by using the and keys to highlight "FUNCTION SETTING", pressing the OK key, highlighting the desired program, and then pressing the OK key. Key Operator Number Change See page 2, REGISTERING THE KEY OPERATOR CODE NUMBER.
Ar-M208_keyope_sec.book 10 ページ 2002年6月12日 水曜日 午後3時41分 KEY OPERATOR PROGRAMS Erase Adjust Set the initial setting of the amount of the erase area with this program. When "ERASE ADJUST" is selected and the OK key is pressed, the following display will appear. ERASE ADJUST 1/4 inch (1/4~1) 1. Adjust the value for the edge erase mode and center erase mode using the and keys. ● The 2. value can be set from 1/4" to 1" in 1/4" increments. Press the OK key.
Ar-M208_keyope_sec.book 11 ページ 2002年6月12日 水曜日 午後3時41分 KEY OPERATOR PROGRAMS Output Trays If a job separator tray kit or a finisher is installed along with a facsimile expansion kit, this program can be used to specify which output tray will be used to receive copies and which will be used to receive prints. When "OUTPUT TRAYS" is selected and the OK key is pressed, the following display will appear.
Ar-M208_keyope_sec.book 12 ページ 2002年6月12日 水曜日 午後3時41分 KEY OPERATOR PROGRAMS Memory for Printer This copier has a memory for storing data of scanned originals. Part of this memory will be used for storing print data. This program is used to set the percentage of the memory used for the printer feature. The default setting is 50%. When "MEM. FOR PRINTER" is selected and the OK key is pressed, the following display will appear. MEM. FOR PRINTER 30% 40% 50% 60% 1.
Ar-M208_keyope_sec.book 13 ページ 2002年6月12日 水曜日 午後3時41分 KEY OPERATOR PROGRAMS TIMER SETTING The programs of this category are used to set the timers for some functions. These programs can be selected by using the and keys to highlight "TIMER SETTING", pressing the OK key, highlighting the desired program, and then pressing the OK key.
Ar-M208_keyope_sec.book 14 ページ 2002年6月12日 水曜日 午後3時41分 KEY OPERATOR PROGRAMS Preheat Mode Preheat mode functions to reduce the power consumption by lowering the temperature of the fusing unit to a programmed level once a programmed length of time has elapsed without any copier operation after the last copy of a run is made or power is turned on. The preheat mode will help lower the user's electricity bill, reduce waste of natural resources, and cut down on environmental pollution.
Ar-M208_keyope_sec.book 15 ページ 2002年6月12日 水曜日 午後3時41分 KEY OPERATOR PROGRAMS ENABLE/DISABLE The programs of this category are used to enable or disable some functions. These programs can be set or canceled by using the and keys to highlight "ENABLE/DISABLE", pressing the OK key, highlighting the desired program, and then pressing the OK key. Disable Auto Paper Selection This program is used to prevent automatic paper selection.
Ar-M208_keyope_sec.book 16 ページ 2002年6月12日 水曜日 午後3時41分 KEY OPERATOR PROGRAMS Disable Auto Power Shut-off The auto power shut-off mode is used to turn off the power to the fuser automatically once a programmed length of time has elapsed without any copier operation after the last copy of a run is made or power is turned on. This mode lowers the user's electricity bill, reduces waste of natural resources, and cuts down on environmental pollution.
Ar-M208_keyope_sec.book 17 ページ 2002年6月12日 水曜日 午後3時41分 KEY OPERATOR PROGRAMS ACCOUNT CONTROL The programs of this category are used to set the internal auditor functions. These programs can be selected by using the and keys to highlight "ACCOUNT CONTROL", pressing the OK key, highlighting the desired program, and then pressing the OK key. Auditing Mode This program is used to enable or disable the basic auditing mode. When enabled, the message in the display will be "Enter your account number.
Ar-M208_keyope_sec.book 18 ページ 2002年6月12日 水曜日 午後3時41分 KEY OPERATOR PROGRAMS Reset Account This program is used to reset all audit accounts or to selectively reset individual accounts. When "RESET ACCOUNT" is selected and the OK key is pressed, the following display will appear. RESET ACCOUNT RESET 1 ACC. RESET ALL ACC. ----To reset all accounts 1. Use the key. and 2. Use the and keys to select "RESET ALL ACC." and press the OK keys to select "YES" and press the OK key.
Ar-M208_keyope_sec.book 19 ページ 2002年6月12日 水曜日 午後3時41分 KEY OPERATOR PROGRAMS To delete accounts 1. Use the and keys to select "DELETE" and press the OK key. 2. To delete all accounts, use the ACC." and press the OK key. and keys to select "DELETE ALL ●A message will appear to confirm the selection. Use the and keys to select "YES" and press the OK key to delete all accounts. If you decide not to delete all accounts, select "NO" and press the OK key. 3.
Ar-M208_keyope_sec.book 20 ページ 2002年6月12日 水曜日 午後3時41分 KEY OPERATOR PROGRAMS OTHER PROGRAM Total Count This program can be selected by using the and keys after the key operator program mode is entered. This program is used to display the total counts, including counts of the copier, RSPF, duplex module, stapler and the printing counts. Also, facsimile, and scanning counts will be displayed if the relevant features are installed. An 11" x 17" sheet is counted as two sheets.
Ar-M208_keyope_sec.
Ar-M208_keyope_sec.book 1 ページ 2002年6月12日 水曜日 午後3時41分 AR-M208 SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430-2135. www.sharp-usa.