Service manual

AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 12
Operation/Procedure
The LCD is changed as shown below. (The contrast changes
every 2sec from the current level to MAX
→ MIN → the current
level. During this period, each LED is lighted.
Operation/Procedure
1) Select the number corresponding to the target of operation
check with 10-key.
2) Press [START] key.
The load selected in procedure 1 performs ON/OFF operation.
Press [CUSTOM SETTINGS] key to stop the operation of the
load.
The ON/OFF operation of the selected heater lamp is
repeated every 500ms five times.
Operation/Procedure
1) Select the number corresponding to the target of operation
check with 10-key.
2) Press [START] key.
The load selected in procedure 1 turns ON for 10sec.
Press [CUSTOM SETTINGS] key to stop the operation.
The copy lamp or CIS is turned on for 10sec and turned off.
NOTE: CIS: only when the DSPF is installed.
Operation/Procedure
1) Select the number corresponding to the target of operation
check with 10-key.
2) Press [START] key.
The load selected in procedure 1 operates.
Press [CUSTOM SETTINGS] key to stop the operation.
5
5-1
Purpose Operation test/Check
Function
(Purpose)
Used to check the operation of the display, LCD in
the operation panel, and control circuit.
Section Operation (Display/Operation key)
Item Operation
After 6.0sec Press [CUSTOM SETTINGS] key,
and the operation is stopped.
5-2
Purpose Operation test/Check
Function
(Purpose)
Used to check the operation of the heater lamp
and the control circuit.
Section Fixing (Fusing)
Item Operation
1 HL1 (LOWER) Heater lamp 1 (Lower)
2 HL2 (UPPER) Heater lamp 2 (Upper)
Press [START] key, and the
operation is started.
Press [CUSTOM SETTINGS] key, and
the operation is stopped.
The operation is repeated the specified
number of times before stopping.
SIMULATION 5-1
SIMULATION 5-1
SIMULATION 5-2
HEATER LAMP TEST. SELECT 1-2, AND PRESS START.
1.HL1(LOWER)
2.HL2(UPPER)
2
SIMULATION 5-2
HEATER LAMP TEST. EXECUTING···.
1.HL1(LOWER)
2.HL2(UPPER)
2
5-3
Purpose Operation test/Check
Function
(Purpose)
Used to check the operation of the scanner lamp
and the control circuit.
Section Optical (Image scanning)
Item Operation
Press [START] key, and the operation
is started.
Press [CUSTOM SETTINGS] key, and
the operation is stopped after 10sec.
6
6-1
Purpose Operation test/Check
Function
(Purpose)
Used to check the operation of the paper transport
system loads and the control circuit.
Section Paper transport (Discharge/Switchback/Transport)
Item Operation
1 MSWPR MSW power relay signal
2 HLPR Heater power relay
3 DCPR DC power relay
4 MM Main motor
5 DM Drum motor
6 POM_FW Paper exit motor forward rotation
7 POM_RV Paper exit motor reverse rotation
8 CPFC Paper feed clutch
9 RRC Resist roller clutch
10 TRC Transport roller clutch
11 FGS_FIN Finisher gate solenoid
12 LUM Tray 1 lift-up motor
13 TRC_DSK Desk clutch sync signal
14 PSPS Separation pawl solenoid
15*1 MCM MP drive motor control signal
16*1 MCPCL MP tray paper feed clutch signal
17*1 MCFCL MP tray transport clutch signal
SIMULATION 5-3
COPY LAMP TEST. SELECT 1-2, AND PRESS START.
1.COPY LAMP
2.CIS
1
SIMULATION 5-3
COPY LAMP TEST. EXECUTING···.
1.COPY LAMP
2.CIS
1