Service manual

AR-M351U/M451U, AR-M355U/M455U SIMULATION 9 - 30
Operation/Procedure
1) Enter the number corresponding to whether AMS operation is
automatically performed or nor in the center binding mode with
the 10-key.
2) Press [START] key.
(Default: 1 for Europe and UK, 0 for the others)
Operation/Procedure
1) Select ENABLE/DISABLE of the B/W reverse mode with 10-
key.
2) Press [START] key.
Operation/Procedure
1) Select YES/NO of the non-print paper count-up with 10-key.
2) Press [START] key.
Non-print paper means an insert paper (without copying) in the
OHP insertion mode, a cover (without copying) in the cover inser-
tion mode, back surface, and white paper in the duplex exit mode
(CA, etc.).
(Default: 0 for Japan and Australia, 1 for the other)
The target counters are as follows:
• Copies counter
• Printer counter
• Department management counter
• Total counter
• Effective paper counter
Operation/Procedure
1) Select ENABLE/DISABLE of the CA key cancel function of
print stop with 10-key.
2) Press [START] key.
(Default: 1)
Operation/Procedure
1) Select the number corresponding to the operation mode with
10-key.
2) Press [START] key.
(Default: 0)
26-41
Purpose Setting
Function
(Purpose)
Used to set the automatic magnification ratio
selection (AMS) in the pamphlet mode.
Section
Item Specifications Operation mode (Common)
0 NO AMS/APS selection allowed
1 YES AMS is forcibly operated.
26-50
Purpose Setting
Function
(Purpose)
Black-White reverse YES/NO setting
Item Specifications Operation
0 DISABLE B/W reverse mode DISABLE
1 ENABLE B/W reverse mode ENABLE Default
26-52
Purpose Setting
Function
(Purpose)
Used to set whether non-print paper (insertion
paper, cover paper) (blank image print paper) is
counted up or not.
Section Paper transport (Discharge/Switchback/Transport)
Item Specifications Operation mode
0 NO (NO COUNT UP) No count up
1 YES (COUNT UP) Count up
SIMULATION 26-41
PAMPHLET MODE AMS SETTING. SELECT 0-1, AND PRESS
START.
0. NO
1. YES
1
SIMULATION 26-50
B/W REVERSE MODE SETTING. SELECT 0-1, AND PRESS
START.
0. DISABLE
1. ENABLE
1
26-68
Purpose Setting
Function
(Purpose)
Used to set ENABLE/DISABLE of the CA key
cancel function of print stop.
Section
Item Specifications Operation
0 DISABLE Disable
1 ENABLE (PRINT STOP) Enable
27
27-1
Purpose Setting
Function
(Purpose)
Used to set the specifications for operations in
case of communication trouble between the host
computer and MODEM (machine side). (When
communication trouble occurs between the host
computer MODEM and the machine, the self diag
display (U7-00) is printed and setting for inhibition
of print or not is made.)
Section Communication unit (TEL/LIU/MODEM etc.)
Item Specifications Operation mode
0 YES Though a communication trouble occurs between
the host computer and the MODEM (machine side),
there is no effect on the machine operations.
1 NO When a communication trouble occurs between the
host computer and the MODEM (machine side), the
self diag display (U7-00) is displayed and printing is
inhibited.
SIMULATION 26-52
BLANK PAPER COUNT UP SETTING. SELECT 0-1, AND PRESS
START.
0. NO (NO COUNT UP)
1. YES (COUNT UP)
1
SIMULATION 26-68
CA KEY CANCEL MODE SETTING. SELECT 0-1, AND PRESS
START.
0. DISABLE
1. ENABLE (PRINT STOP)
0
SIMULATION 27-1
DISABLING OF U7-00 TROUBLE. SELECT 0-1, AND PRESS START.
0. YES
1. NO
1